* <b>Internet Key Exchange (IKE)</b> protocols. Dynamically generates and distributes cryptographic keys for AH and ESP.
==Authentication Header (AH)==
==Internet Key Exchange Protocol (IKE)==
AH is a protocol that provides authentication of either all or part of the contents of a datagram through the addition of a header that is calculated based on the values in the datagram. What parts of the datagram are used for the calculation, and the placement of the header, depends whether tunnel or transport mode is used.
The Internet Key Exchange (IKE) is a protocol that provides authenticated keying material for Internet Security Association and Key Management Protocol (ISAKMP) framework. There are other key exchange schemes that work with ISAKMP, but IKE is the most widely used one. Together they provide means for authentication of hosts and automatic management of security associations (SA).
Most of the time IKE daemon is doing nothing. There are two possible situations when it is activated:
The presence of the AH header allows to verify the integrity of the message, but doesn't encrypt it. Thus, AH provides authentication but not privacy. Another protocol (ESP) is considered superior, it provides data privacy and also its own authentication method.
There is some traffic caught by a policy rule which needs to become encrypted or authenticated, but the policy doesn't have any SAs. The policy notifies IKE daemon about that, and IKE daemon initiates connection to remote host.
IKE daemon responds to remote connection.
In both cases, peers establish connection and execute 2 phases:
*'''Phase 1''' - The peers agree upon algorithms they will use in the following IKE messages and authenticate. The keying material used to derive keys for all SAs and to protect following ISAKMP exchanges between hosts is generated also. This phase should match following settings:
**authentication method
** DH group
** encryption algorithm
** exchange mode
** hash alorithm
** NAT-T
** DPD and lifetime (optional)
RouterOS supports the following authentication algorithms for AH:
*'''Phase 2''' - The peers establish one or more SAs that will be used by IPsec to encrypt data. All SAs established by IKE daemon will have lifetime values (either limiting time, after which SA will become invalid, or amount of data that can be encrypted by this SA, or both). This phase should match following settings:
<ul>
** Ipsec protocol
<li> SHA2 (256, 512)
** mode (tunnel or transport)
<li> SHA1
** authentication method
<li> MD5
** PFS (DH) group
</ul>
** lifetime
{{Note | There are two lifetime values - soft and hard. When SA reaches it's soft lifetime treshold, the IKE daemon receives a notice and starts another phase 2 exchange to replace this SA with fresh one. If SA reaches hard lifetime, it is discarded. }}
{{Warning | Phase 1 is not re-keyed if DPD is disabled when lifetime expires, only phase 2 is re-keyed. To force phase 1 re-key, enable DPD.}}
===Transport mode===
{{Warning | PSK authentication was known to be vulnerable against Offline attacks in "aggressive" mode, however recent discoveries indicate that offline attack is possible also in case of "main" and "ike2" exchange modes. General recommendation is to avoid using PSK authentication method.}}
In transport mode AH header is inserted after IP header. IP data and header is used to calculate authentication value. IP fields that might change during transit, like TTL and hop count, are set to zero values before authentication.
IKE can optionally provide a Perfect Forward Secrecy (PFS), which is a property of key exchanges, that, in turn, means for IKE that compromising the long term phase 1 key will not allow to easily gain access to all IPsec data that is protected by SAs established through this phase 1. It means an additional keying material is generated for each phase 2.
Generation of keying material is computationally very expensive. Exempli gratia, the use of modp8192 group can take several seconds even on very fast computer. It usually takes place once per phase 1 exchange, which happens only once between any host pair and then is kept for long time. PFS adds this expensive operation also to each phase 2 exchange.
===Tunnel mode===
===Diffie-Hellman Groups===
In tunnel mode original IP packet is encapsulated within a new IP packet. All of the original IP packet is authenticated.
Diffie-Hellman (DH) key exchange protocol allows two parties without any initial shared secret to create one securely. The following Modular Exponential (MODP) and Elliptic Curve (EC2N) Diffie-Hellman (also known as "Oakley") Groups are supported:
<tr><td>Group 19</td><td>256 bits random ECP group</td><td>RFC 5903</td></tr>
<tr><td>Group 20</td><td>384 bits random ECP group</td><td>RFC 5903</td></tr>
<tr><td>Group 21</td><td>521 bits random ECP group</td><td>RFC 5903</td></tr>
</table>
Encapsulating Security Payload (ESP) uses shared key encryption to provide data privacy. ESP also supports its own authentication scheme like that used in AH.
More on standards can be found [https://www.iana.org/assignments/ipsec-registry/ipsec-registry.xhtml here].
ESP packages its fields in a very different way than AH. Instead of having just a header, it divides its fields into three components:
===IKE Traffic===
<ul >
<li><b>ESP Header</b> - Comes before the encrypted data and its placement depends on whether ESP is used in transport mode or tunnel mode.
<li><b>ESP Trailer</b> - This section is placed after the encrypted data. It contains padding that is used to align the encrypted data.
<li><b>ESP Authentication Data</b> - This field contains an Integrity Check Value (ICV), computed in a manner similar to how the AH protocol works, for when ESP's optional authentication feature is used.
</ul>
===Transport mode===
To avoid problems with IKE packets hit some SPD rule and require to encrypt it with not yet established SA (that this packet perhaps is trying to establish), locally originated packets with UDP source port 500 are not processed with SPD. The same way packets with UDP destination port 500 that are to be delivered locally are not processed in incoming policy check.
In transport mode ESP header is inserted after original IP header. ESP trailer and authentication value is added to the end of the packet. In this mode only IP payload is encrypted and authenticated, IP header is not secured.
[[File:ESP-transport wiki.png]]
=== Setup Procedure ===
===Tunnel mode===
To get IPsec to work with automatic keying using IKE-ISAKMP you will have to configure policy, peer and proposal (optional) entries.
In tunnel mode original IP packet is encapsulated within a new IP packet thus securing IP payload and IP header.
{{Warning | Ipsec is very sensitive to time changes. If both ends of the IpSec tunnel are not synchronizing time equally(for example, different NTP servers not updating time with the same timestamp), tunnels will break and will have to be established again.}}
[[File:ESP-tunnel wiki.png]]
===Encryption algorithms===
=== EAP Authentication methods ===
RouterOS ESP supports various encryption and authentication algorithms.
<table border="1">
<tr>
Authentication:
<th>Outer Auth</th>
<ul class="bullets">
<th>Inner Auth</th>
<li><b>MD5</b>
</tr>
<li><b>SHA1</b>
<tr>
<li><b>SHA2 (256-bit, 512-bit)</b>
<td>EAP-GTC</td>
</ul>
<td></td>
Encryption:
<ul class="bullets">
<li><b>AES</b> - 128-bit, 192-bit and 256-bit key AES-CBC, AES-CTR and AES-GCM algorithms;
<li><b>Blowfish</b> - added since v4.5
<li><b>Twofish</b> - added since v4.5
<li><b>Camellia</b> - 128-bit, 192-bit and 256-bit key Camellia encryption algorithm added since v4.5
<nowiki>*</nowiki> supported only 128 bit and 256 bit key sizes
<b>EAP-TLS</b> on Windows is called "Smart Card or other certificate".
<nowiki>**</nowiki> only manufactured since 2016, serial numbers that begin with number 5 and 7
==Authentication Header (AH)==
AH is a protocol that provides authentication of either all or part of the contents of a datagram through the addition of a header that is calculated based on the values in the datagram. What parts of the datagram are used for the calculation, and the placement of the header, depends whether tunnel or transport mode is used.
<nowiki>***</nowiki> AES-CBC and AES-CTR only encryption is accelerated, hashing done in software
IPsec throughput results of various encryption and hash algorithm combinations are published on [https://mikrotik.com/product/ MikroTik products page]. When testing throughput, please follow the guidelines available in the [[Manual:Tools/Traffic_Generator#IpSec_tunnel_performance_test|Traffic Generator manual page]]
The presence of the AH header allows to verify the integrity of the message, but doesn't encrypt it. Thus, AH provides authentication but not privacy. Another protocol (ESP) is considered superior, it provides data privacy and also its own authentication method.
==Internet Key Exchange Protocol==
The Internet Key Exchange (IKE) is a protocol that provides authenticated keying material for Internet Security Association and Key Management Protocol (ISAKMP) framework. There are other key exchange schemes that work with ISAKMP, but IKE is the most widely used one. Together they provide means for authentication of hosts and automatic management of security associations (SA).
RouterOS supports the following authentication algorithms for AH:
<ul>
<li> SHA2 (256, 512)
<li> SHA1
<li> MD5
</ul>
Most of the time IKE daemon is doing nothing. There are two possible situations when it is activated:
===Transport mode===
There is some traffic caught by a policy rule which needs to become encrypted or authenticated, but the policy doesn't have any SAs. The policy notifies IKE daemon about that, and IKE daemon initiates connection to remote host.
In transport mode AH header is inserted after IP header. IP data and header is used to calculate authentication value. IP fields that might change during transit, like TTL and hop count, are set to zero values before authentication.
IKE daemon responds to remote connection.
In both cases, peers establish connection and execute 2 phases:
*'''Phase 1''' - The peers agree upon algorithms they will use in the following IKE messages and authenticate. The keying material used to derive keys for all SAs and to protect following ISAKMP exchanges between hosts is generated also. This phase should match following settings:
**authentication method
** DH group
** encryption algorithm
** exchange mode
** hash alorithm
** NAT-T
** DPD and lifetime (optional)
*'''Phase 2''' - The peers establish one or more SAs that will be used by IPsec to encrypt data. All SAs established by IKE daemon will have lifetime values (either limiting time, after which SA will become invalid, or amount of data that can be encrypted by this SA, or both). This phase should match following settings:
===Tunnel mode===
** Ipsec protocol
** mode (tunnel or transport)
In tunnel mode original IP packet is encapsulated within a new IP packet. All of the original IP packet is authenticated.
** authentication method
** PFS (DH) group
==Encapsulating Security Payload (ESP)==
** lifetime
{{Note | There are two lifetime values - soft and hard. When SA reaches it's soft lifetime treshold, the IKE daemon receives a notice and starts another phase 2 exchange to replace this SA with fresh one. If SA reaches hard lifetime, it is discarded. }}
Encapsulating Security Payload (ESP) uses shared key encryption to provide data privacy. ESP also supports its own authentication scheme like that used in AH.
{{Warning | Phase 1 is not re-keyed if DPD is disabled when lifetime expires, only phase 2 is re-keyed. To force phase 1 re-key, enable DPD.}}
ESP packages its fields in a very different way than AH. Instead of having just a header, it divides its fields into three components:
<ul >
<li><b>ESP Header</b> - Comes before the encrypted data and its placement depends on whether ESP is used in transport mode or tunnel mode.
<li><b>ESP Trailer</b> - This section is placed after the encrypted data. It contains padding that is used to align the encrypted data.
<li><b>ESP Authentication Data</b> - This field contains an Integrity Check Value (ICV), computed in a manner similar to how the AH protocol works, for when ESP's optional authentication feature is used.
</ul>
IKE can optionally provide a Perfect Forward Secrecy (PFS), which is a property of key exchanges, that, in turn, means for IKE that compromising the long term phase 1 key will not allow to easily gain access to all IPsec data that is protected by SAs established through this phase 1. It means an additional keying material is generated for each phase 2.
===Transport mode===
Generation of keying material is computationally very expensive. Exempli gratia, the use of modp8192 group can take several seconds even on very fast computer. It usually takes place once per phase 1 exchange, which happens only once between any host pair and then is kept for long time. PFS adds this expensive operation also to each phase 2 exchange.
In transport mode ESP header is inserted after original IP header. ESP trailer and authentication value is added to the end of the packet. In this mode only IP payload is encrypted and authenticated, IP header is not secured.
===Diffie-Hellman Groups===
[[File:ESP-transport wiki.png]]
Diffie-Hellman (DH) key exchange protocol allows two parties without any initial shared secret to create one securely. The following Modular Exponential (MODP) and Elliptic Curve (EC2N) Diffie-Hellman (also known as "Oakley") Groups are supported:
===Tunnel mode===
<table border="1">
In tunnel mode original IP packet is encapsulated within a new IP packet thus securing IP payload and IP header.
More on standards can be found [https://www.iana.org/assignments/ipsec-registry/ipsec-registry.xhtml here].
[[File:ESP-tunnel wiki.png]]
===IKE Traffic===
===Encryption algorithms===
To avoid problems with IKE packets hit some SPD rule and require to encrypt it with not yet established SA (that this packet perhaps is trying to establish), locally originated packets with UDP source port 500 are not processed with SPD. The same way packets with UDP destination port 500 that are to be delivered locally are not processed in incoming policy check.
RouterOS ESP supports various encryption and authentication algorithms.
Authentication:
<ul class="bullets">
<li><b>MD5</b>
<li><b>SHA1</b>
<li><b>SHA2 (256-bit, 512-bit)</b>
</ul>
=== Setup Procedure ===
Encryption:
<ul class="bullets">
<li><b>AES</b> - 128-bit, 192-bit and 256-bit key AES-CBC, AES-CTR and AES-GCM algorithms;
<li><b>Blowfish</b> - added since v4.5
<li><b>Twofish</b> - added since v4.5
<li><b>Camellia</b> - 128-bit, 192-bit and 256-bit key Camellia encryption algorithm added since v4.5
<li><b>3DES</b> - 168-bit DES encryption algorithm;
</ul>
To get IPsec to work with automatic keying using IKE-ISAKMP you will have to configure policy, peer and proposal (optional) entries.
===Hardware acceleration===
{{Warning | Ipsec is very sensitive to time changes. If both ends of the IpSec tunnel are not synchronizing time equally(for example, different NTP servers not updating time with the same timestamp), tunnels will break and will have to be established again.}}
Hardware acceleration allows to do faster encryption process by using built-in encryption engine inside CPU.
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
|desc=List of subnets in CIDR format, which to tunnel. Subnets will be sent to the peer using CISCO UNITY extension, remote peer will create specific dynamic policies.
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<tr><td>[https://mikrotik.com/product/wap_ac_lte_kit RBwAPGR-5HacD2HnD&R11e-LTE (wAP ac LTE kit)] *</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<tr><td>[https://mikrotik.com/product/wap_ac_4g_kit RBwAPGR-5HacD2HnD&R11e-4G (wAP ac 4G kit)] *</td>
|prop=Property
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<tr><td>[https://mikrotik.com/product/wap_ac_lte6_kit RBwAPGR-5HacD2HnD&R11e-LTE6 (wAP ac LTE6 kit)] *</td>
|arg=address
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
|desc=IP address assigned to the client. If not set dynamic address is used allocated from the address-pool defined in [[#Mode_Config | Mode Config menu]].
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightpink">no</td><td style="background-color:lightpink">no</td><td style="background-color:lightpink">no</td>
<!-- DES and 3DES --><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
<tr><td>[https://mikrotik.com/product/rb1100ahx4 RB1100AHx4] and [https://mikrotik.com/product/RB1100Dx4 RB1100AHx4 Dude Edition]</td>
<!-- DES and 3DES --><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td>
Peer configuration settings are used to establish connections between IKE daemons ([[#Internet_Key_Exchange_Protocol | '''phase 1''']] configuration). This connection then will be used to negotiate keys and algorithms for SAs.
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightpink">no</td><td style="background-color:lightpink">no</td><td style="background-color:lightpink">no</td>
Starting from v6rc12 responder side now uses initiator exchange type for peer config selection. It means that you can configure multiple ipsec peers with the same address but different exchange modes.
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
{{Note | exchange modes '''main''' and '''l2tp-main''' are treated the same, so these modes cannot be used select config between multiple peers.}}
<tr><td>[https://mikrotik.com/product/rb4011igs_rm RB4011iGS+RM] and [https://mikrotik.com/product/rb4011igs_5hacq2hnd_in RB4011iGS+5HacQ2HnD-IN]</td>
<!-- DES and 3DES --><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td>
<!-- DES and 3DES --><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td>
<!-- DES and 3DES --><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightgreen">yes</td><td style="background-color:lightpink">no</td>
|desc=If remote peer's address matches this prefix, then the peer configuration is used in authentication and establishment of '''Phase 1'''. If several peer's addresses match several configuration entries, the most specific one (i.e. the one with largest netmask) will be used.
<!-- DES and 3DES --><td style="background-color:lightpink">no</td><td style="background-color:lightpink">no</td><td style="background-color:lightpink">no</td><td style="background-color:lightpink">no</td>
* <var>eap-radius</var> - IKEv2 EAP RADIUS passthrough authentication for responder (RFC 3579). Server certificate in this case is required. If server certificate is not specified then only clients supporting EAP-only (RFC 5998) will be able to connect. Note that EAP method should be compatible with EAP-only.
</table>
* <var>pre-shared-key</var> - authenticate by a password (secret) string shared between the peers
* <var>rsa-signature</var> - authenticate using a pair of RSA certificates
<nowiki>*</nowiki> supported only 128 bit and 256 bit key sizes
* <var>rsa-key</var> - authenticate using a RSA key imported in [[#Keys | Ipsec key]] menu.
<nowiki>**</nowiki> only manufactured since 2016, serial numbers that begin with number 5 and 7
* <var>rsa-signature-hybrid</var> - responder certificate authentication with initiator Xauth. <var>passive</var> parameter identifies server/client side
<nowiki>***</nowiki> AES-CBC and AES-CTR only encryption is accelerated, hashing done in software
<nowiki>****</nowiki> DES is not supported, only 3DES and AES-CBC
IPsec throughput results of various encryption and hash algorithm combinations are published on [https://mikrotik.com/product/ MikroTik products page]. When testing throughput, please follow the guidelines available in the [[Manual:Tools/Traffic_Generator#IpSec_tunnel_performance_test|Traffic Generator manual page]]
Policy table is used to determine whether security settings should be applied to a packet.
'''Properties'''
{{Mr-arg-table-h
|prop=Property
|desc=Description
}}
}}
{{Mr-arg-table
{{Mr-arg-table
|arg=certificate
|arg=action
|type=string
|type=discard {{!}} encrypt {{!}} none
|default=
|default=encrypt
|desc=Name of a certificate listed in [[M:System/Certificates | certificate table]] (signing packets; the certificate must have private key). Applicable if RSA signature authentication method (auth-method=rsa-signature) is used.
|desc=Specifies what to do with packet matched by the policy.
* <var>none</var> - pass the packet unchanged.
* <var>discard</var> - drop the packet.
* <var>encrypt</var> - apply transformations specified in this policy and it's SA.
}}
}}
Line 380:
Line 496:
|type=string
|type=string
|default=
|default=
|desc=Short description of the peer.
|desc=Short description of the policy.
}}
}}
{{Mr-arg-table
{{Mr-arg-table
|arg=compatibility-options
|arg=disabled
|type=skip-peer-id-validation
|type=yes {{!}} no
|default=
|default=no
|desc=Compatibility options to work with peers not following RFC guidelines.
|desc=List of encryption algorithms that will be used by the peer.
|desc=Specifies what to do if some of the SAs for this policy cannot be found:
* <var>use</var> - skip this transform, do not drop packet and do not acquire SA from IKE daemon;
* <var>require</var> - drop packet and acquire SA;
* <var>unique</var> - drop packet and acquire a unique SA that is only used with this particular policy. It is used in setups where multiple clients can sit behind one public IP address (clients behind NAT).
}}
}}
{{Mr-arg-table
{{Mr-arg-table
|arg=exchange-mode
|arg=peer
|type=aggressive {{!}} base {{!}} main {{!}} main-l2tp {{!}} ike2
|type=string
|default=main
|default=
|desc=Different ISAKMP phase 1 exchange modes according to RFC 2408. Do not use other modes then main unless you know what you are doing.
|desc=Name of the [[#Peers | peer]] on which the policy applies.
'''main-l2tp''' mode relaxes rfc2409 section 5.4, to allow pre-shared-key authentication in main mode. <var>ike2</var> mode enables Ikev2 RFC 7296. Parameters that are ignored by Ikev2 <var>proposal-check</var>, <var>compatibility-options</var>, <var>lifebytes</var>, <var>dpd-maximum-failures</var>.
}}
}}
{{Mr-arg-table
{{Mr-arg-table
|arg=generate-policy
|arg=proposal
|type=no {{!}} port-override {{!}} port-strict
|type=string
|default=no
|default=default
|desc=Allow this peer to establish SA for non-existing policies. Such policies are created dynamically for the lifetime of SA. Automatic policies allows, for example, to create IPsec secured [[M:Interface/L2TP | L2TP]] tunnels, or any other setup where remote peer's IP address is not known at the configuration time.
|desc=Name of the [[#Proposals| proposal template]] that will be sent by IKE daemon to establish SAs for this policy.
* <var>no</var> - do not generate policies
* <var>port-override</var> -- generate policies and force policy to use '''any''' port (old behavior)
* <var>port-strict</var> -- use ports from peer's proposal, which should match peer's policy
|desc=Hashing algorithm. SHA (Secure Hash Algorithm) is stronger, but slower. MD5 uses 128-bit key, sha1-160bit key.
|desc=IP packet protocol to match.
}}
}}
{{Mr-arg-table
{{Mr-arg-table
|arg=key
|arg=src-address
|type=string
|type=ip/ipv6 prefix
|default=
|default=0.0.0.0/32
|desc=Name of the key from [[#Keys | key menu]]. Applicable if auth-method=rsa-key.
|desc=Source address to be matched in packets. Applicable when tunnel mode (<var>tunnel=yes</var>) or template (<var>template=yes</var>) is used.
}}
}}
{{Mr-arg-table
{{Mr-arg-table
|arg=lifebytes
|arg=src-port
|type=Integer: 0..4294967295
|type=any {{!}} integer:0..65535
|default=0
|default=any
|desc=Phase 1 lifebytes is used only as administrative value which is added to proposal. Used in cases if remote peer requires specific lifebytes value to establish phase 1.
|desc=Source port to be matched in packets. If set to <var>any</var> all ports will be matched.
}}
}}
{{Mr-arg-table
{{Mr-arg-table
|arg=lifetime
|arg=template
|type=time
|type=yes {{!}} no
|default=1d
|default=no
|desc=Phase 1 lifetime: specifies how long the SA will be valid.
|desc=Creates a template and assigns it to specified [[#Groups | policy group]].
Following parameters are used by template:
* <var>group</var> - name of the [[#Groups | policy group]] to which this template is assigned;
* <var>src-address</var>, <var>dst-address</var> - Requested subnet must match in both directions(for example 0.0.0.0/0 to allow all);
* <var>protocol</var> - protocol to match, if set to all, then any protocol is accepted;
* <var>proposal</var> - SA parameters used for this template;
* <var>level</var> - useful when <var>unique</var> is required in setups with multiple clients behind NAT.
}}
}}
{{Mr-arg-table
{{Mr-arg-table-end
|arg=local-address
|arg=tunnel
|type=IP/IPv6 Address
|type=yes {{!}} no
|default=
|default=no
|desc=Routers local address on which Phase 1 should be bounded to.
|desc=Specifies whether to use tunnel mode.
}}
}}
{{Mr-arg-table
|arg=mode-config
|type=none {{!}} request-only {{!}} string
|default=none
|desc=Name of the mode config parameters from [[#Mode_Config | <code>mode-config</code> menu]]. When parameter is set mode-config is enabled.
* initiator peer on phase1 will send mode-config request and will set assigned IP address and DNS.
* responder will assign ip address if address-pool is specified, will send also DNS server addresses and split-include subnets (if defined).
|desc=This parameter sets IKE ID to specified mode. It is possible to manually set two modes FQDN and USER_FQDN.
* '''FQDN''' - fully qualified domain name
* '''USER_FQDN''' - specifies a fully-qualified username string, for example, "user@domain.com";
* '''address''' - IP address is used as ID;
* '''auto''' - tries to use correct ID automatically: IP for PSK, FQDN for Cert based connections;
* '''key-id''' - Use the specified key-id for the identity
{{Mr-arg-table-h
|prop=Property
|desc=Description
}}
}}
{{Mr-arg-table
{{Mr-arg-ro-table
|arg=nat-traversal
|arg=active
|type=yes {{!}} no
|type=yes {{!}} no
|default=no
|desc=Whether this policy is currently in use.
|desc=Use Linux NAT-T mechanism to solve IPsec incompatibility with NAT routers inbetween IPsec peers. This can only be used with ESP protocol (AH is not supported by design, as it signs the complete packet, including IP header, which is changed by NAT, rendering AH signature invalid). The method encapsulates IPsec ESP traffic into UDP streams in order to overcome some minor issues that made ESP incompatible with NAT.
}}
}}
{{Mr-arg-table
{{Mr-arg-ro-table
|arg=notrack-chain
|arg=default
|type=string
|type=yes {{!}} no
|default=
|desc=Whether this is a default system entry.
|desc=Adds raw firewall rules matching ipsec policy to specified chain.
}}
}}
{{Mr-arg-table
{{Mr-arg-ro-table
|arg=passive
|arg=dynamic
|type=yes {{!}} no
|type=yes {{!}} no
|default=no
|desc=Whether this is a dynamically added or generated entry.
|desc=When passive mode is enabled will wait for remote peer to initiate IKE connection. Enabled passive mode also indicates that peer is xauth responder, and disabled passive mode - xauth initiator. When passive mode is disabled peer will try to establish not only phase1, but also phase2 automatically, if policies are configured or created during phase1.
}}
}}
{{Mr-arg-table
{{Mr-arg-ro-table
|arg=policy-template-group
|arg=invalid
|type=none {{!}} string
|type=yes {{!}} no
|default=
|desc=Whether this policy is invalid - possible cause is duplicate policy with the same <var>src-address</var> and <var>dst-address</var>.
|desc=If generate-policy is enabled, responder checks against templates from the same [[#Policy_Groups | group]]. If none of the templates match, Phase2 SA will not be established.
}}
}}
{{Mr-arg-table
{{Mr-arg-ro-table
|arg=port
|arg=ph2-count
|type=integer:0..65535
|type=integer
|default=500
|desc=Number of active phase 2 sessions associated with the policy.
|desc=Communication port used (when router is initiator) to connect to remote peer in cases if remote peer uses non-default port.
}}
}}
{{Mr-arg-table
{{Mr-arg-ro-table
|arg=proposal-check
|arg=ph2-state
|type=claim {{!}} exact {{!}} obey {{!}} strict
|type=expired {{!}} no-phase2 {{!}} established
|default=obey
|desc=Indication of the progress of key establishing.
|desc=Phase 2 lifetime check logic:
* <var>claim</var> - take shortest of proposed and configured lifetimes and notify initiator about it
* <var>exact</var> - require lifetimes to be the same
* <var>obey</var> - accept whatever is sent by an initiator
* <var>strict</var> - if proposed lifetime is longer than the default then reject proposal otherwise accept proposed lifetime
}}
}}
{{Mr-arg-table
{{Mr-arg-table
|arg=remote-certificate
|arg=sa-dst-address
|type=string
|type=ip/ipv6 address
|default=
|default=::
|desc=Name of a certificate (listed in [[M:System/Certificates | certificate table]]) for authenticating the remote side (validating packets; no private key required). Applicable if RSA signature authentication method is used.
If remote-certificate is not specified then received certificate from remote peer is used and checked against CA in [[Manual:System/Certificates | certificate store]]. Proper CA must be imported in certificate store.
}}
}}
{{Mr-arg-table
{{Mr-arg-table-end
|arg=secret
|arg=sa-src-address
|type=string
|type=ip/ipv6 address
|default=
|default=::
|desc=Secret string (in case pre-shared key authentication is used). If it starts with '0x', it is parsed as a hexadecimal value
|desc=SA source IP/IPv6 address (local peer).
}}
}}
{{Mr-arg-table
|arg=send-initial-contact
|type=yes {{!}} no
|default=yes
|desc=Specifies whether to send "initial contact" IKE packet or wait for remote side, this packet should trigger removal of old peer SAs for current source address.
Usually in road warrior setups clients are initiators and this parameter should be set to no. Initial contact is not sent if modecfg or xauth is enabled for ikev1.
}}
{{Mr-arg-table
{{Warning | policy order is important starting form v6.40. Now it works similar as firewall filters where policies are executed from top to bottom (<var>priority</var> parameter is removed).}}
|arg=xauth-login
|type=string
|default=
|desc=initiator (client) XAuth username
}}
{{Mr-arg-table-end
{{Note |
|arg=xauth-password
All packets are IPIP encapsulated in tunnel mode, and their new IP header's src-address and dst-address are set to sa-src-address and sa-dst-address values of this policy. If you do not use tunnel mode (id est you use transport mode), then only packets whose source and destination addresses are the same as sa-src-address and sa-dst-address can be processed by this policy. Transport mode can only work with packets that originate at and are destined for IPsec peers (hosts that established security associations). To encrypt traffic between networks (or a network and a host) you have to use tunnel mode.
IPSec phases information is erased, when /ip ipsec peer configuration is modified on the fly, however packets are being encrypted/decrypted because of installed-sa (for example remote-peers information is erased, when peer configuration is modified.}}
==Keys==
This menu shows various IPsec statistics and errors.
|desc=No state is found i.e. either inbound SPI, address, or IPsec protocol at SA is wrong.
}}
Policy table is used to determine whether security settings should be applied to a packet.
{{Mr-arg-ro-table
|arg=in-state-protocol-errors
{{Warning | policy order is important starting form v6.40. Now it works similar as firewall filters where policies are executed from top to bottom (<var>priority</var> parameter is removed).}}
|type=integer
|desc=Transformation protocol specific error, for example SA key is wrong or hardware accelerator is unable to handle amount of packets.
}}
{{Mr-arg-table-h
{{Mr-arg-ro-table
|prop=Property
|arg=in-state-mode-errors
|desc=Description
|type=integer
|desc=Transformation mode specific error.
}}
}}
{{Mr-arg-table
|arg=action
|type=discard {{!}} encrypt {{!}} none
|default=encrypt
|desc=Specifies what to do with packet matched by the policy.
* <var>none</var> - pass the packet unchanged
* <var>discard</var> - drop the packet
* <var>encrypt</var> - apply transformations specified in this policy and it's SA
}}
{{Mr-arg-table
{{Mr-arg-ro-table
|arg=comment
|arg=in-state-sequence-errors
|type=string
|type=integer
|default=
|desc=Sequence number is out of window.
|desc=Short description of the policy
}}
}}
{{Mr-arg-table
|arg=disabled
|type=yes {{!}} no
|default=no
|desc=Whether policy is used to match packets.
}}
{{Mr-arg-table
{{Mr-arg-ro-table
|arg=dst-address
|arg=in-state-expired
|type=IP/IPv6 prefix
|type=integer
|default=0.0.0.0/32
|desc=State is expired.
|desc=Destination address to be matched in packets.
}}
}}
{{Mr-arg-table
{{Mr-arg-ro-table
|arg=dst-port
|arg=in-state-mismatches
|type=integer:0..65535 {{!}} any
|type=integer
|default=any
|desc=State has mismatched option, for example UDP encapsulation type is mismatched.
|desc=Destination port to be matched in packets. If set to '''any''' all ports will be matched
}}
}}
{{Mr-arg-table
{{Mr-arg-ro-table
|arg=group
|arg=in-state-invalid
|type=string
|type=integer
|default=default
|desc=State is invalid.
|desc=Name of the [[#Policy_Group | policy group]] to which this template is assigned.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-table
|arg=in-template-mismatches
|arg=ipsec-protocols
|type=integer
|type=ah {{!}} esp
|desc=No matching template for states, e.g. inbound SAs are correct but SP rule is wrong. Possible cause is mismatched sa-source or sa-destination address.
|default=esp
|desc=Specifies what combination of Authentication Header and Encapsulating Security Payload protocols you want to apply to matched traffic
}}
}}
{{Mr-arg-table
{{Mr-arg-ro-table
|arg=level
|arg=in-no-policies
|type=require {{!}} unique {{!}} use
|type=integer
|default=require
|desc=No policy is found for states, e.g. inbound SAs are correct but no SP is found.
|desc=Specifies what to do if some of the SAs for this policy cannot be found:
* <var>use</var> - skip this transform, do not drop packet and do not acquire SA from IKE daemon
* <var>require</var> - drop packet and acquire SA
* <var>unique</var> - drop packet and acquire a unique SA that is only used with this particular policy. It is used in setups where multiple clients can sit behind one public IP address (clients behind NAT).
}}
}}
{{Mr-arg-table
{{Mr-arg-ro-table
|arg=manual-sa
|arg=in-policy-blocked
|type=string {{!}} none
|type=integer
|default=none
|desc=Policy discards.
|desc=Name of the [[#Manual SA|manual SA]] template
}}
}}
{{Mr-arg-table
{{Mr-arg-ro-table
|arg=proposal
|arg=in-policy-errors
|type=string
|type=integer
|default=default
|desc=Policy errors.
|desc=Name of the [[#Proposal settings|proposal template]] that will be sent by IKE daemon to establish SAs for this policy.
|desc=Creates a template and assigns it to specified [[#Policy_Group | policy group]]
Following parameters are used by template:
* src-address, dst-address - Requested subnet must match in both directions(for example 0.0.0.0/0 to allow all)
* protocol - protocol to match, if set to all, then any protocol is accepted
* proposal - SA parameters used for this template
* level - useful when 'unique' is required in setups with multiple clients behind NAT.
}}
}}
{{Mr-arg-table-end
{{Mr-arg-ro-table
|arg=tunnel
|arg=out-state-sequence-errors
|type=yes {{!}} no
|type=integer
|default=no
|desc=Sequence errors, for example sequence number overflow.
|desc=Specifies whether to use tunnel mode
}}
}}
{{Mr-arg-ro-table
|arg=out-state-expired
|type=integer
|desc=State is expired.
}}
{{Note |
{{Mr-arg-ro-table
All packets are IPIP encapsulated in tunnel mode, and their new IP header's src-address and dst-address are set to sa-src-address and sa-dst-address values of this policy. If you do not use tunnel mode (id est you use transport mode), then only packets whose source and destination addresses are the same as sa-src-address and sa-dst-address can be processed by this policy. Transport mode can only work with packets that originate at and are destined for IPsec peers (hosts that established security associations). To encrypt traffic between networks (or a network and a host) you have to use tunnel mode.
|arg=out-policy-blocked
|type=integer
|desc=Policy discards.
}}
}}
{{Mr-arg-ro-table
===Policy Stats===
|arg=out-policy-dead
|type=integer
Read-only parameters
|desc=Policy is dead.
{{Mr-arg-table-h
|prop=Property
|desc=Description
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-ro-table-end
|arg=ph2-count
|arg=out-policy-errors
|type=integer
|type=integer
|desc=Number of active phase2 sessions associated with the policy.
|desc=Indication of the progress of key establishing.
}}
{{Mr-arg-ro-table-end
Proposal information that will be sent by IKE daemons to establish SAs for certain policy.
|arg=priority
|type=
|desc=Shows kernel priority
}}
Additionally you can get policy stats with command <b><code>/ip ipsec policy print stats</code></b> will show current status of the policy. Additional read-only parameters will be printed.
'''Properties'''
{{Mr-arg-table-h
{{Mr-arg-table-h
Line 814:
Line 849:
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-table
|arg=in-accepted
|arg=auth-algorithms
|type=integer
|type=md5{{!}}null{{!}}sha1{{!}}sha256{{!}}sha512
|desc=How many incoming packets were passed by the policy without an attempt to decrypt.
|default=sha1
|desc=Allowed algorithms for authorization. SHA (Secure Hash Algorithm) is stronger, but slower. MD5 uses 128-bit key, sha1-160bit key.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-table
|arg=in-dropped
|arg=comment
|type=integer
|type=string
|desc=How many incoming packets were dropped by the policy without an attempt to decrypt
|default=
|desc=
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-table
|arg=in-transformed
|arg=disabled
|type=integer
|type=yes {{!}} no
|desc=How many incoming packets were decrypted (ESP) and/or verified (AH) by the policy
In this menu it is possible to create additional policy groups used by policy templates.
Proposal information that will be sent by IKE daemon to establish SAs for this policy ([[#Internet_Key_Exchange_Protocol | '''Phase 2''']]). Configured proposals are set in [[#Policy | policy configuration]].
'''Properties'''
{{Mr-arg-table-h
{{Mr-arg-table-h
Line 885:
Line 928:
{{Mr-arg-table
{{Mr-arg-table
|arg=auth-algorithms
|arg=name
|type=md5{{!}}sha1{{!}}null{{!}}sha256{{!}}sha512
|type=string
|default=sha1
|default=
|desc=Allowed algorithms for authorization. SHA (Secure Hash Algorithm) is stronger, but slower. MD5 uses 128-bit key, sha1-160bit key..
Peer configuration settings are used to establish connections between IKE daemons. This connection then will be used to negotiate keys and algorithms for SAs. Exchange mode is the only unique identifier between the peers, meaning that there can be multiple peer configurations with the same <var>remote-address</var> as long as different <var>exchange-mode</var> is used.
|desc=Allowed algorithms and key lengths to use for SAs.
|desc=If remote peer's address matches this prefix, then the peer configuration is used in authentication and establishment of '''Phase 1'''. If several peer's addresses match several configuration entries, the most specific one (i.e. the one with largest netmask) will be used.
}}
}}
{{Mr-arg-table
{{Mr-arg-table
|arg=lifetime
|arg=comment
|type=time
|type=string
|default=30m
|default=
|desc=How long to use SA before throwing it out.
|desc=Short description of the peer.
}}
}}
{{Mr-arg-table
{{Mr-arg-table
|arg=name
|arg=disabled
|type=string
|type=yes {{!}} no
|default=
|default=no
|desc=Name of the proposal template, that will be identified in other parts of ipsec configuration.
|desc=Whether peer is used to match remote peer's prefix.
Menu is used to configure SAs manually. Created SA template then can be used in [[#Policy | policy]] configuration.
{{Mr-arg-table-h
|prop=Property
|desc=Description
}}
}}
{{Mr-arg-table
{{Mr-arg-table
|arg=ah-algorithm
|arg=exchange-mode
|type=in/out <br />
|type=aggressive {{!}} base {{!}} main {{!}} ike2
in,out = md5{{!}}null{{!}}sha1
|default=main
|default=null
|desc=Different ISAKMP phase 1 exchange modes according to RFC 2408.
|desc=Authentication Header encryption algorithm.
'''main''' mode relaxes rfc2409 section 5.4, to allow pre-shared-key authentication in main mode. <var>ike2</var> mode enables Ikev2 RFC 7296. Parameters that are ignored by IKEv2 <var>proposal-check</var>, <var>compatibility-options</var>, <var>lifebytes</var>, <var>dpd-maximum-failures</var>, <var>nat-traversal</var>.
|desc=Routers local address on which Phase 1 should be bounded to.
}}
}}
{{Mr-arg-table
{{Mr-arg-table
|arg=ah-spi
|arg=name
|type=0x100..FFFFFFFF/0x100..FFFFFFFF
|type=string
|default=0x100
|default=
|desc=Incoming-SA-SPI/outgoing-SA-SPI
|desc=
}}
}}
{{Mr-arg-table
{{Mr-arg-table
|arg=disabled
|arg=passive
|type=yes {{!}} no
|type=yes {{!}} no
|default=no
|default=no
|desc=Defines whether item is ignored or used
|desc=When passive mode is enabled will wait for remote peer to initiate IKE connection. Enabled passive mode also indicates that peer is xauth responder, and disabled passive mode - xauth initiator. When passive mode is disabled peer will try to establish not only phase1, but also phase2 automatically, if policies are configured or created during phase1.
}}
}}
{{Mr-arg-table
{{Mr-arg-table
|arg=esp-auth-algorithm
|arg=port
|type=in/out<br />
|type=integer:0..65535
in,out = md5{{!}}null{{!}}sha1
|default=500
|default=null
|desc=Communication port used (when router is initiator) to connect to remote peer in cases if remote peer uses non-default port.
|desc=Specifies whether to send "initial contact" IKE packet or wait for remote side, this packet should trigger removal of old peer SAs for current source address.
|desc=Incoming-encryption-algorithm
Usually in road warrior setups clients are initiators and this parameter should be set to no. Initial contact is not sent if modecfg or xauth is enabled for ikev1.
This facility provides information about installed security associations including the keys.
Identities are configuration parameters that are specific to the remote peer. Main purpose of an identity is to handle authentication and verify peer's integrity.
* <var>digital-signature</var> - authenticate using a pair of RSA certificates;
* <var>eap</var> - IKEv2 EAP authentication for initiator (peer with netmask of /32). Must be used together with <var>eap-methods</var>;
* <var>eap-radius</var> - IKEv2 EAP RADIUS passthrough authentication for responder (RFC 3579). Server certificate in this case is required. If server certificate is not specified then only clients supporting EAP-only (RFC 5998) will be able to connect. Note that EAP method should be compatible with EAP-only;
* <var>pre-shared-key</var> - authenticate by a password (pre-shared secret) string shared between the peers (not recommended since offline attack on pre-shared key is possible);
* <var>rsa-key</var> - authenticate using a RSA key imported in [[#Keys | keys]] menu. Only supported in IKEv1;
* <var>pre-shared-key-xauth</var> - authenticate by a password (pre-shared secret) string shared between the peers + XAuth username and password. Only supported in IKEv1;
* <var>rsa-signature-hybrid</var> - responder certificate authentication with initiator XAuth. Only supported in IKEv1.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-table
|arg=ESP
|arg=certificate
|type=yes {{!}} no
|type=string
|desc=
|default=
|desc=Name of a certificate listed in [[M:System/Certificates | System/Certificates]] (signing packets; the certificate must have private key). Applicable if digital signature authentication method (<var>auth-method=digital-signature</var>) or EAP (<var>auth-method=eap</var>) is used.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-table
|arg=add-lifetime
|arg=comment
|type=time/time
|type=string
|desc=Added lifetime for the SA in format soft/hard
|default=
* soft - time period after which ike will try to establish new SA
|desc=Short description of the identity.
* hard - time period after which SA is deleted
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-table
|arg=addtime
|arg=disabled
|type=time
|type=yes {{!}} no
|desc=Date and time when this SA was added.
|default=no
|desc=Whether identity is used to match remote peer.
}}
}}
{{Mr-arg-ro-table
|arg=auth-algorithm
|type=sha1 {{!}} md5
|desc=Shows currently used authentication algorithm
|desc=All EAP methods requires whole certificate chain including intermediate and root CA certificates to be present in [[M:System/Certificates | System/Certificates]] menu. Also <var>username</var> and <var>password</var> (if required by authentication server) must be specified. Multiple EAP methods may be specified and will be used in specified order. Currently supported EAP methods:
* <var>eap-mschapv2</var>;
* <var>eap-peap</var> - also known as PEAPv0/EAP-MSCHAPv2;
|desc=Allow this peer to establish SA for non-existing policies. Such policies are created dynamically for the lifetime of SA. Automatic policies allows, for example, to create IPsec secured [[M:Interface/L2TP | L2TP]] tunnels, or any other setup where remote peer's IP address is not known at the configuration time.
* <var>no</var> - do not generate policies;
* <var>port-override</var> - generate policies and force policy to use '''any''' port (old behavior);
* <var>port-strict</var> - use ports from peer's proposal, which should match peer's policy.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-table
|arg=dst-address
|arg=key
|type=IP
|type=string
|desc=
|default=
|desc=Name of the private key from [[#Keys | keys]] menu. Applicable if RSA key authentication method (<var>auth-method=rsa-key</var>) is used.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-table
|arg=enc-algorithm
|arg=match-by
|type=des {{!}} 3des {{!}} aes ...
|type=remote-id {{!}} certificate
|desc=Shows currently used encryption algorithm
|default=remote-id
|desc=Defines the logic used for peer's identity validation.
* <var>remote-id</var> - will verify the peer's ID according to <var>remote-id</var> setting.
* <var>certificate</var> will verify the peer's certificate with what is specified under <var>remote-certificate</var> setting.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-table
|arg=pfs
|arg=mode-config
|type=yes {{!}} no
|type=none {{!}} *request-only {{!}} string
|desc=
|default=none
|desc=Name of the configuration parameters from [[#Mode_Configs | mode-config]] menu. When parameter is set mode-config is enabled.
|desc=On initiator, this controls what ID_i is sent to the responder. On responder, this controls what ID_r is sent to the initiator. In IKEv2, responder also expects this ID in received ID_r from initiator.
* <var>auto</var> - tries to use correct ID automatically;
* <var>address</var> - IP address is used as ID;
* <var>fqdn</var> - fully qualified domain name;
* <var>key-id</var> - use the specified key ID for the identity;
* <var>user fqdn</var> - specifies a fully-qualified username string, for example, "user@domain.com".
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-table
|arg=spi
|arg=notrack-chain
|type=string
|type=string
|desc=
|default=
|desc=Adds [[M:IP/Firewall/Raw | IP/Firewall/Raw]] rules matching IPsec policy to specified chain. Use together with <var>generate-policy</var>.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-table
|arg=src-address
|arg=password
|type=IP
|type=string
|desc=
|default=
|desc=XAuth or EAP password. Applicable if pre-shared key with XAuth authentication method (<var>auth-method=pre-shared-key-xauth</var>) or EAP (<var>auth-method=eap</var>) is used.
}}
}}
{{Mr-arg-ro-table-end
{{Mr-arg-table
|arg=state
|arg=peer
|type=string
|type=string
|desc=Shows the current state of the SA ("mature", "dying" etc)
|default=
|desc=Name of the [[#Peers | peer]] on which the identity applies.
}}
}}
===Flushing SAs===
{{Mr-arg-table
|arg=policy-template-group
|type=none {{!}} string
|default=default
|desc=If <var>generate-policy</var> is enabled, traffic selectors are checked against templates from the same [[#Groups | group]]. If none of the templates match, Phase 2 SA will not be established.
}}
Sometimes after incorrect/incomplete negotiations took place, it is required to flush manually the installed SA table so that SA could be renegotiated. This option is provided by the <code>/ip ipsec installed-sa flush</code> command.
{{Mr-arg-table
|arg=remote-certificate
|type=string
|default=
|desc=Name of a certificate (listed in [[M:System/Certificates | System/Certificates]]) for authenticating the remote side (validating packets; no private key required). If <var>remote-certificate</var> is not specified then received certificate from remote peer is used and checked against CA in certificate menu. Proper CA must be imported in certificate store. If <var>remote-certificate</var> and <var>match-by=certificate</var> is specified, only the specific client certificate will be matched. Applicable if digital signature authentication method (<var>auth-method=digital-signature</var>) is used.
|desc=This parameter controls what ID value to expect from the remote peer. Note that all types except for <var>ignore</var> will verify remote peer's ID with received certificate. In case when the peer sends certificate name as its ID, it is checked against the certificate, else the ID is checked against Subject Alt. Name.
* <var>auto</var> - accept all ID's;
* <var>fqdn</var> - fully qualified domain name. Only supported in IKEv2;
* <var>user fqdn</var> - a fully-qualified username string, for example, "user@domain.com". Only supported in IKEv2;
* <var>key-id</var> - specific key ID for the identity. Only supported in IKEv2;
* <var>ignore</var> - do not verify received ID with certificate (dangerous).
}}
{{Mr-arg-table-h
{{Mr-arg-table
|prop=Property
|arg=remote-key
|desc=Description
|type=string
|default=
|desc=Name of the public key from [[#Keys | keys]] menu. Applicable if RSA key authentication method (<var>auth-method=rsa-key</var>) is used.
}}
}}
{{Mr-arg-table
|arg=secret
|type=string
|default=
|desc=Secret string. If it starts with '0x', it is parsed as a hexadecimal value. Applicable if pre-shared key authentication method (<var>auth-method=pre-shared-key</var> and <var>auth-method=pre-shared-key-xauth</var>) is used.
}}
{{Mr-arg-table-end
{{Mr-arg-table-end
|arg=sa-type
|arg=username
|type=ah {{!}} all {{!}} esp
|type=string
|default=all
|default=
|desc=Specifies SA types to flush:
|desc=XAuth or EAP username. Applicable if pre-shared key with XAuth authentication method (<var>auth-method=pre-shared-key-xauth</var>) or EAP (<var>auth-method=eap</var>) is used.
* <var>ah</var> - delete AH protocol SAs only
* <var>esp</var> - delete ESP protocol SAs only
* <var>all</var> - delete both ESP and AH protocols SAs
|desc=Whether this is a dynamically added entry by different service (e.g L2TP).
}}
This submenu provides you with various statistics about remote peers that currently have established phase 1 connections with this router. Note that if peer doesn't show up here, it doesn't mean that no IPsec traffic is being exchanged with it.
==Profiles==
Profiles defines a set of parameters that will be used for IKE negotiation during Phase 1. These parameters may be common with other peer configurations.
|desc=State of phase 1 negotiation with the peer. For example when phase1 and phase 2 are negotiated it will show state "established".
|default=aes-128
|desc=List of encryption algorithms that will be used by the peer.
}}
}}
{{Mr-arg-ro-table-end
{{Mr-arg-table
|arg=established
|arg=hash-algorithm
|type=time
|type=md5 {{!}} sha1 {{!}} sha256 {{!}} sha512
|desc=How long peers are in established state.
|default=sha1
|desc=Hashing algorithm. SHA (Secure Hash Algorithm) is stronger, but slower. MD5 uses 128-bit key, sha1-160bit key.
}}
}}
{{Mr-arg-table
|arg=lifebytes
|type=Integer: 0..4294967295
|default=0
|desc=Phase 1 lifebytes is used only as administrative value which is added to proposal. Used in cases if remote peer requires specific lifebytes value to establish phase 1.
}}
===Closing all IPsec connections===
{{Mr-arg-table
|arg=lifetime
|type=time
|default=1d
|desc=Phase 1 lifetime: specifies how long the SA will be valid.
}}
Menu has a command to quickly close all established ipsec connections. This command will clear all installed SAs (Phase2) and remove all entries from remote-peers menu (Phase1).
|desc=All inbound errors that are not matched by other counters.
|default=yes
|desc=Use Linux NAT-T mechanism to solve IPsec incompatibility with NAT routers inbetween IPsec peers. This can only be used with ESP protocol (AH is not supported by design, as it signs the complete packet, including IP header, which is changed by NAT, rendering AH signature invalid). The method encapsulates IPsec ESP traffic into UDP streams in order to overcome some minor issues that made ESP incompatible with NAT.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-table-end
|arg=in-buffer-errors
|arg=proposal-check
|type=integer
|type=claim {{!}} exact {{!}} obey {{!}} strict
|desc=No free buffer.
|default=obey
|desc=Phase 2 lifetime check logic:
* <var>claim</var> - take shortest of proposed and configured lifetimes and notify initiator about it
* <var>exact</var> - require lifetimes to be the same
* <var>obey</var> - accept whatever is sent by an initiator
* <var>strict</var> - if proposed lifetime is longer than the default then reject proposal otherwise accept proposed lifetime
This menu provides various statistics about remote peers that currently have established phase 1 connection.
{{Mr-arg-ro-table
|arg=in-no-states
|type=integer
|desc=No state is found i.e. Either inbound SPI, address, or IPsec protocol at SA is wrong
}}
'''Read only properties'''
{{Mr-arg-ro-table
{{Mr-arg-table-h
|arg=in-state-protocol-errors
|prop=Property
|type=integer
|desc=Description
|desc=Transformation protocol specific error, for example SA key is wrong or hardware accelerator is unable to handle amount of packets.
}}
}}
{{Mr-arg-ro-table
|arg=dynamic-address
|type=ip/ipv6 address
|desc=Dynamically assigned IP address by [[#Mode_configs | mode config]]
}}
{{Mr-arg-ro-table
{{Mr-arg-ro-table
|arg=in-state-mode-errors
|arg=last-seen
|type=integer
|type=time
|desc=Transformation mode specific error
|desc=Duration since last message received by this peer.
}}
}}
{{Mr-arg-ro-table
|arg=local-address
|type=ip/ipv6 address
|desc=Local address on the router used by this peer.
}}
{{Mr-arg-ro-table
{{Mr-arg-ro-table
|arg=in-state-sequence-errors
|arg=natt-peer
|type=integer
|type=yes {{!}} no
|desc=Sequence number is out of window
|desc=Whether NAT-T is used for this peer.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-ro-table
|arg=in-state-expired
|arg=ph2-total
|type=integer
|type=integer
|desc=State is expired
|desc=Total amount of active IPsec security associations.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-ro-table
|arg=in-state-mismatches
|arg=remote-address
|type=integer
|type=ip/ipv6 address
|desc=State has mismatched option, for example UDP encapsulation type is mismatched.
|desc=Remote peer's ip/ipv6 address.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-ro-table
|arg=in-state-invalid
|arg=responder
|type=integer
|type=yes {{!}} no
|desc=State is invalid
|desc=Whether the connection is initiated by remote peer.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-ro-table
|arg=in-template-mismatches
|arg=rx-bytes
|type=integer
|type=integer
|desc=No matching template for states, e.g. Inbound SAs are correct but SP rule is wrong. Possible cause is mismatched sa-source or sa-destination address.
|desc=Total amount of bytes received from this peer.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-ro-table
|arg=in-no-policies
|arg=rx-packets
|type=integer
|type=integer
|desc=No policy is found for states, e.g. Inbound SAs are correct but no SP is found
|desc=Total amount of packets received from this peer.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-ro-table
|arg=in-policy-blocked
|arg=side
|type=integer
|type=initiator {{!}} responder
|desc=Policy discards
|desc=Shows which side initiated the Phase1 negotiation.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-ro-table
|arg=in-policy-errors
|arg=state
|type=integer
|type=string
|desc=Policy errors
|desc=State of phase 1 negotiation with the peer. For example when phase1 and phase 2 are negotiated it will show state "established".
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-ro-table
|arg=out-errors
|arg=tx-bytes
|type=integer
|type=integer
|desc=All outbound errors that are not matched by other counters
|desc=Total amount of bytes transmitted to this peer.
}}
}}
{{Mr-arg-ro-table
{{Mr-arg-ro-table
|arg=out-bundle-errors
|arg=tx-packets
|type=integer
|type=integer
|desc=Bundle generation error
|desc=Total amount of packets transmitted to this peer.
|desc=Specifies whether the configuration will work as an initiator (client) or responder (server). Initiator will request for mode-config parameters from responder.
}}
Client side config:
{{Mr-arg-table
|arg=split-include
|type=list of IP prefix
|default=
|desc=List of subnets in CIDR format, which to tunnel. Subnets will be sent to the peer using CISCO UNITY extension, remote peer will create specific dynamic policies.
|desc=Specifying an address list will generate dynamic source NAT rules. This parameter is only available with <var>responder=no</var>. [[#RoadWarrior_client_with_NAT | RoadWarrior client with NAT]]
}}
{{Mr-arg-table
|arg=static-dns
|type=list of IP
|default=
|desc=Manually specified DNS server's IP address to be sent to the client.
}}
{{Note | On server side it is mandatory to set <var>passive</var> to '''yes''' when XAuth is used. }}
{{Mr-arg-table-end
|arg=system-dns
|type=yes {{!}} no
|default=
|desc=When this option is enabled DNS addresses will be taken from <code>/ip dns</code>.
}}
===Road Warrior setup with Mode Conf===
'''Read only properties'''
{{Mr-arg-table-h
|prop=Property
|desc=Description
}}
{{Mr-arg-ro-table-end
|arg=default
|type=yes {{!}} no
|default=
|desc=Whether this is a default system entry.
}}
{{ Note | Not all IKE implementations support multiple split networks provided by split-include option. }}
Consider setup where worker need to access other co-workers (workstations) and local office server remotely.
{{ Note | If RouterOS client is initiator, it will always send CISCO UNITY extension, and RouterOS supports only split-include from this extension.}}
Office has two subnets:
* 192.168.55.0/24 for workstations
* 192.168.66.0/24 network that must not be reachable by RoadWarrior clients
* 10.5.8.0/24 for servers
And access to those networks should be secure.
[[file:ipsec-road-warrior.png]]
{{ Note | It is not possible to use system-dns and static-dns at the same time.}}
Typically in RoadWarrior setups as this it is impossible to know from which address user will connect, so we need to set up <var>generate-policy</var> parameter on the server side. However this leads to other problems, client can generate any policy and access any network in the office. Even set 0.0.0.0/0 and deny internet access to office workers.
'''Mode Conf''', '''policy group''' and '''policy templates''' will allow us to overcome these problems.
This menu provides information about installed security associations including the keys.
====IPsec Server Config====
At first we need a pool from which RoadWarrior will will get an address. Typically in office you set up DHCP server for local workstations, the same DHCP pool can be used.
For iOS devices to be able to connect, '''proposal''' changes are needed:
{{Mr-arg-ro-table
|arg=enc-algorithm
|type=des {{!}} 3des {{!}} aes-cbc {{!}} ...
|desc=Currently used encryption algorithm.
}}
* does not work with 3des encryption algorithm, '''aes-128/256''' works
{{Mr-arg-ro-table
* auth algorithm must be '''sha1'''
|arg=enc-key
* PFS group must be '''none'''
|type=string
* lifetime must be '''8 hours'''
|desc=Used encryption key.
}}
Example of valid proposal configuration for iOS devices:
{{Mr-arg-ro-table
<pre>
|arg=enc-key-size
/ip ipsec proposal
|type=number
set default enc-algorithms=aes-128-cbc,aes-256-cbc lifetime=8h \
|desc=Used encryption key length.
pfs-group=none
}}
</pre>
{{ Note | Iphone does not work with split-include 0.0.0.0/0. If you set 0.0.0.0/0 for older clients traffic will not be sent over the tunnel, for newer ios clients tunnel will not be established.}}
{{Mr-arg-ro-table
|arg=expires-in
|type=yes {{!}} no
|desc=Time left until rekeying.
}}
==== Android Client Notes ====
{{Mr-arg-ro-table
|arg=hw-aead
|type=yes {{!}} no
|desc=Whether this SA is [[#Hardware_acceleration | hardware accelerated]].
}}
Android devices are trying to add policy with destination 0.0.0.0/0, so you have to make sure that correct policy template is added.
Now that we have certificates, server can be configured. Note that windows client requires modeconf, so we will use it to give out IP addresses from pool and send DNS, we also need to modify default template a little, to allow policies only from specific source addresses and generate unique level (required by multiple clients behind the same public IP):
{{Mr-arg-table-h
<pre>
|prop=Property
/ip pool add name=rw-pool ranges=192.168.77.2-192.168.77.254
{{Note | Windows uses point-to-point links so specifying any prefix other than 32 in mode-config settings will do nothing. Split include subnets are ignored as well}}
{{Mr-arg-ro-table
|arg=key-size
|type=1024 {{!}} 2048 {{!}} 4096
|desc=Size of this key.
}}
{{Note | Currently RouterOS does not support any of EAP authentication methods}}
{{Mr-arg-ro-table
|arg=private-key
|type=yes {{!}} no
|desc=Whether this is a private key.
}}
==== RouterOS client configuration ====
{{Mr-arg-ro-table-end
|arg=rsa
|type=yes {{!}} no
|desc=Whether this is a RSA key.
}}
Generate a new certificate for the client and sign it with previously created CA. Export the client certificate in PKCS12 format.
A file named <b>cert_export_RouterOS_client.p12</b> is now located in the routers Files section. Transfer the file to the RouterOS client device and import it.
|desc=Export public key to file from one of existing private keys.
}}
There should now be the self-signed CA certificate and the client certificate in Certificate menu. Usually the client certificate is imported first, but lets double check which is it.
{{Mr-arg-ro-table
|arg=generate-key
|type=key-size; name
|desc=Generate private key. Takes two parameters, name of newly generated key and key size 1024,2048 and 4096.
}}
<pre>
{{Mr-arg-ro-table-end
/put [/certificate get [find common-name=RouterOS_client] name]
|arg=import
</pre>
|type=file-name; name
|desc=Import key from file.
<b>cert_export_RouterOS_client.p12_0</b> is the client certificate. Now we can create the peer configuration.
Verify that the connection is successfully established.
<pre>
{{Mr-arg-table-h
/ip ipsec
|prop=Property
remote-peers print
|desc=Description
installed-sa print
}}
</pre>
==== Windows client configuration ====
{{Mr-arg-table
|arg=accounting
|type=yes {{!}} no
|default=
|desc=Whether to send RADIUS accounting requests to RADIUS server. Applicable if EAP Radius (<var>auth-method=eap-radius</var>) or pre-shared key with XAuth authentication method (<var>auth-method=pre-shared-key-xauth</var>) is used.
}}
Generate a new certificate for the client and sign it with previously created CA. Export the client certificate in PKCS12 format.
{{Mr-arg-table
|arg=interim-update
|type=time
|default=
|desc=Interval between each consecutive RADIUS accounting Interim update. Accounting must be enabled.
|desc=Whether to use [[Manual:RADIUS_Client | Radius client]] for XAuth users or not.
</pre>
}}
A file named <b>cert_export_Windows_client.p12</b> is now located in the routers Files section. Download and open the certificate file on the Windows computer. Install the certificate by following the instructions. Make sure you select Local Machine store location.
==Application Guides==
[[File:Ike2v2_cert_win.png | 1300px]]
===RoadWarrior client with NAT===
Consider setup as illustrated below. RouterOS acts as a RoadWarrior client connected to Office allowing access to its internal resources.
[[file:Ipsec-road-warrior-client.png]]
You can now proceed to Network and Internet settings -> VPN and add a new configuration. Fill in the Connection name, Server name or address parameters. Select IKEv2 under VPN type. When it is done, it is necessary to select "Use machine certificates". This can be done in Network and Sharing Center by clicking the Properties menu for the VPN connection. The setting is located under Security tab.
Tunnel is established, local mode-config IP address is received and a set of dynamic policies are generated.
[[File:Ike2v2_conf_win.png | 1300px]]
<pre>
[admin@pair_r1] > ip ipsec policy print
Flags: T - template, X - disabled, D - dynamic, I - invalid, A - active, * - default
0 T * group=default src-address=::/0 dst-address=::/0 protocol=all proposal=default template=yes
Currently Windows 10 is compatible with the following Phase 1 (Peer) and Phase 2 (Proposal) proposal sets:
1 DA src-address=192.168.77.254/32 src-port=any dst-address=10.5.8.0/24 dst-port=any protocol=all
Currently only packets with source address of 192.168.77.254/32 will match the IPsec policies. For local network to be able to reach remote subnets, it is necessary to change the source address of local hosts to the dynamically assigned mode config IP address. It is possible to generate source NAT rules dynamically. This can be done by creating a new address list which contains of all local networks that NAT rule should be applied. In our case, it is 192.168.88.0/24.
By specifying the address list under mode-config initiator configuration, a set of source NAT rules will be dynamically generated.
{{Warning | Phase 2 (/ip ipsec proposal) PFS Group must be set to 'none' for rekeying to work properly.}}
<pre>
/ip ipsec mode-config set [ find name="request-only" ] src-address-list=local-RW
</pre>
==== Android Client Notes ====
When the IPsec tunnel is established, we can see the dynamically created source NAT rules for each network. Now every host in 192.168.88.0/24 is able to access Office's internal resources.
Native Android client does not support ikev2 at the moment. StrongSwan client from Play Store can be used to connect to ikev2 server.
<pre>
StrongSwan client the same as windows accept certificates and keys in pkcs12 format. So external tool is needed to convert exported .crt and .key files to .pfx and then import .pfx file.
Ca certificate is selected automatically as shown in screenshot below, but if for some reason you need to specify exact CA certificate, then unselect "Select automatically" and pick imported CA from the list.
When connecting Android StrongSwan clients, make sure that on RouterOS proposal settings DH group is disabled, otherwise phase2 will fail.
==== macOS client configuration ====
{{Note | On server side it is mandatory to set <var>passive</var> to '''yes''' when XAuth is used. }}
Generate a new certificate for the client and sign it with previously created CA. Export the client certificate in PKCS12 format.
===Allow only IPsec encapsulated traffic===
There are some scenarios where for security reasons you would like to drop access from/to specific networks if incoming/outgoing packets are not encrypted. For example, if we have L2TP/IPsec setup we would want to drop non encrypted L2TP connection attempts.
There are several ways how to achieve this:
* Using IPsec policy matcher in firewall;
* Using generic IPsec policy with <var>action</var> set to '''drop''' and lower priority (can be used in Road Warrior setups where dynamic policies are generated);
* By setting DSCP or priority in mangle and matching the same values in firewall after decapsulation.
====IPsec policy matcher====
Lets set up IPsec policy matcher to accept all packets that matched any of IPsec policies and drop the rest:
A file named <b>cert_export_macOS_client.p12</b> is now located in the routers Files section. Download and open the certificate file on the macOS computer and install the certificate in "System" keychain. It is necessary to mark the CA certificate as trusted manually since it is self-signed. Locate the certificate macOS Keychain Access app under System tab and mark it as Always Trust.
IPsec policy matcher takes two parameters '''direction,policy'''. We used incoming direction and IPsec policy. IPsec policy option allows us to inspect packets after decapsulation, so for example if we want to allow only gre encapsulated packet from specific source address and drop the rest we could set up following rules:
You can now proceed to System Preferences -> Network and add a new configuration by clicking the + button. Select Interface: VPN, VPN Type: IKEv2 and name your connection. Remote ID must be set equal to common-name or subjAltName of server's certificate. Local ID can be left blank. Under Authentication Settings select None and choose the client certificate. You can now test the connectivity.
Currently macOS is compatible with the following Phase 1 (Peer) and Phase 2 (Proposal) proposal sets:
The trick of this method is to add default policy with action drop. Lets assume we are running L2TP/IPsec server on public 1.1.1.1 address and we want to drop all non encrypted L2TP:
Now router will drop any L2TP unencrypted incoming traffic, but after successful L2TP/IPsec connection dynamic policy is created with higher priority than it is on default static rule and packets matching that dynamic rule can be forwarded.
<table class="styled_table" style="width:50%">
{{ Note | Policy order is important! For this to work, make sure the static drop policy is below the dynamic policies. Move it below the policy template if necessary. }}
When installing certificates, check which formats iOS supports, client certificate can not be imported from CRT and KEY files, but you can use PKCS12 format. Typically PKCS12 bundle contains also CA certificate, but iOS does not install this CA, so self-signed CA certificate must be installed separately using PEM format.
===Manually specifying local-address parameter under Peer configuration===
====Using different routing table====
IPsec, as any other service in RouterOS, uses main routing table regardless what <var>local-address</var> parameter is used for Peer configuration. It is necessary to apply routing marks to both IKE and IPSec traffic.
Consider the following example. There are two default routes - one in main routing table and another in routing table "backup". It is necessary to use the backup link for IPsec site to site tunnel.
<pre>
<pre>
/certificate
[admin@pair_r1] > /ip route print detail
export-certificate ca type=pem
Flags: X - disabled, A - active, D - dynamic, C - connect, S - static, r - rip, b - bgp, o - ospf, m - mme, B - blackhole, U - unreachable, P - prohibit
0 A S dst-address=0.0.0.0/0 gateway=10.155.107.1 gateway-status=10.155.107.1 reachable via ether1 distance=1 scope=30 target-scope=10 routing-mark=backup
</pre>
1 A S dst-address=0.0.0.0/0 gateway=172.22.2.115 gateway-status=172.22.2.115 reachable via ether2 distance=1 scope=30 target-scope=10
Two files are now located in the routers Files section: <b>cert_export_ca.crt</b> and <b>cert_export_iOS_client.p12</b>. Download and open these files on the iOS device and install both certificates by following the instructions. It is necessary to mark the self-signed CA certificate as trusted on the iOS device. This can be done in Settings -> General -> About -> Certificate Trust Settings menu. When it is done, check whether both certificates are marked as "verified" under Settings -> General -> Profiles menu.
You can now proceed to Settings -> General -> VPN menu and add a new configuration. Remote ID must be set equal to common-name or subjAltName of server's certificate. Local ID can be left blank.
Currently, we see "phase1 negotiation failed due to time up" errors in the log. It is because IPsec tries to reach the remote peer using the main routing table with incorrect source address. It is necessary to mark UDP/500, UDP/4500 and ipsec-esp packets using Mangle.
Consider the following example. There are multiple IP addresses from the same subnet on the public interface. Masquerade rule is configured on out-interface. It is necessary to use one of the IP addresses explicitly.
{{Warning | Phase 2 (/ip ipsec proposal) PFS Group must be set to 'none' for rekeying to work properly.}}
<pre>
{{Note | If you are connected to the VPN over WiFi, the iOS device can go into sleep mode and disconnect from the network.}}
[admin@pair_r1] > /ip address print
Flags: X - disabled, I - invalid, D - dynamic
# ADDRESS NETWORK INTERFACE
0 192.168.1.1/24 192.168.1.0 bridge-local
1 172.22.2.1/24 172.22.2.0 ether1
2 172.22.2.2/24 172.22.2.0 ether1
3 172.22.2.3/24 172.22.2.0 ether1
==== strongSwan client configuration ====
[admin@pair_r1] > /ip route print
Flags: X - disabled, A - active, D - dynamic, C - connect, S - static, r - rip, b - bgp, o - ospf, m - mme, B - blackhole, U - unreachable, P - prohibit
# DST-ADDRESS PREF-SRC GATEWAY DISTANCE
1 A S 0.0.0.0/0 172.22.2.115 1
3 ADC 172.22.2.0/24 172.22.2.1 ether1 0
4 ADC 192.168.1.0/24 192.168.1.1 bridge-local 0
Generate a new certificate for the client and sign it with previously created CA. Export both client and CA certificates in PEM format.
Three files are now located in the routers Files section: <b>cert_export_ca.crt</b>, <b>cert_export_strongSwan_client.crt</b> and <b>cert_export_strongSwan_client.key</b>. strongSwan accepts either PEM or DER format certificates and it is possible to just change the certificate extensions. The private key must be in PKCS1 format - it will need to be converted. We can do this with OpenSSL. Rename the certificates for a more convenient look.
IPsec peer and policy configuration is created using one of the public IP addresses.
Download the certificates and the key to strongSwan client device and move the files to their appropriate directory. By default /etc/ipsec.d/ is used for certificate storage.
Currently the phase 1 connection uses a different source address than we specified and "phase1 negotiation failed due to time up" errors are shown in the logs. This is because masquerade is changing the source address of the connection to match pref-src address of the connected route. Solution is to exclude connections from the public IP address from being masqueraded.
Consider setup as illustrated below. Two remote office routers are connected to internet and office workstations are behind NAT. Each office has its own local subnet, 10.1.202.0/24 for Office1 and 10.1.101.0/24 for Office2. Both remote offices needs secure tunnel to local networks behind routers.
[[file:site-to-site-ipsec-example.png]]
====Site 1 configuration====
Start off by creating new Phase 1 [[#Profiles | profile]] and Phase 2 [[#Proposals | proposal]] entries using stronger or weaker encryption parameters that suits your needs. It is advised to create separate entries for each menu so that they are unique for each [[#Peers | peer]] in case it is necessary to adjust any of the settings in the future. These parameters must match between the sites or else the connection will not establish.
Add exported passphrase for the private key to /etc/ipsec.secrets file
Continue by configuring a [[#Peers | peer]]. Specify the <var>address</var> of the remote router. This address should be reachable through UDP/500 and UDP/4500 ports, so make sure appropriate actions are taken regarding the router's firewall. Specify the <var>name</var> for this peer as well as the newly created <var>profile</var>.
You can now restart (or start) the ipsec daemon and initialize the connection
The next step is to create an [[#Identities | identity]]. For a basic pre-shared key secured tunnel, there is nothing much to set except for a '''strong''' <var>secret</var> and the <var>peer</var> to which this identity applies.
<pre>
<pre>
$ ipsec restart
/ip ipsec identity
$ ipsec up ikev2
add peer=ike1-site2 secret=thisisnotasecurepsk
</pre>
</pre>
===Road Warrior setup Ikev1 RSA Auth===
{{Warning | If security matters, consider using IKEv2 and a different <var>auth-method</var>. }}
====Creating Certificates====
Lastly, create a [[#Policies | policy]] which controls the networks/hosts between whom traffic should be encrypted.
All certificates can be created on RouterOS server using certificate manager.
<pre>
[[Manual:Create_Certificates#Generate_certificates_on_RouterOS | <code>See example >></code>]]
Office 2 configuration is almost identical as Office 1 with proper IP address configuration. Start off by creating new Phase 1 [[#Profiles | profile]] and Phase 2 [[#Proposals | proposal]] entries.
Notice R flag, which means that certificate is revoked
At this point, the tunnel should be established and two IPsec Security Associations should be created on both routers:
<pre>
<pre>
[admin@pe0] /certificate> print
/ip ipsec
Flags: K - private-key, D - dsa, L - crl, C - smart-card-key,
active-peers print
A - authority, I - issued, R - revoked, E - expired, T - trusted
installed-sa print
# NAME COMMON-NAME FINGERPRINT
0 K L A T myCa myCa 7fa636e6576495fe78f1a4...
1 K I T server server cf0650a291bf4685f2fbd3...
2 K I client1 client1 26233de30e89b203b946ab...
3 K R client2 client2 cf172b62201befaf8d8966...
</pre>
</pre>
====NAT and Fasttrack Bypass====
Now if you kill current connection client2 will no be able to establish phase1.
At this point if you try to send traffic over the IPsec tunnel, it will not work, packets will be lost. This is because both routers have NAT rules (masquerade) that is changing source address before packet is encrypted. Router is unable to encrypt the packet, because source address do not match address specified in policy configuration. For more information see [[M:Packet_Flow#IPsec_encryption | IPsec packet flow example]].
===Site to Site IpSec Tunnel===
To fix this we need to set up [[M:IP/Firewall/NAT | IP/Firewall/NAT]] bypass rule.
Two remote office routers are connected to internet and office workstations behind routers are NATed. Each office has its own local subnet, 10.1.202.0/24 for Office1 and 10.1.101.0/24 for Office2. Both remote offices needs secure tunnel to local networks behind routers.
{{Note | If you previously tried to establish an IP connection before NAT bypass rule was added, you have to clear connection table from existing connection or restart both routers. }}
On both routers ether1 is used as wan port and ether2 is used to connect workstations. Also NAT rules are set tu masquerade local networks.
It is very important that bypass rule is placed at the top of all other NAT rules.
Another issue is if you have [[M:IP/Fasttrack | IP/Fasttrack]] enabled, packet bypasses IPsec policies. So we need to add accept rule before FastTrack.
However, this can add significant load to router's CPU if there is a fair amount of tunnels and significant traffic on each tunnel.
/ip route
Solution is to use [[M:IP/Firewall/Raw | IP/Firewall/Raw]] to bypass connection tracking, that way eliminating need of filter rules listed above and reducing load on CPU by approximately 30%.
===Road Warrior setup using IKEv2 with RSA authentication===
<pre>
/ip address
This example explains how to establish a secure IPsec connection between a device connected to the Internet (road warrior client) and a device running RouterOS acting as a server.
Next step is to add peer's configuration. We need to specify peers address and port and pre-shared-key. Other parameters are left to default values.
Before configuring IPsec, it is required to set up certificates. It is possible to use a separate Certificate Authority for certificate management, however in this example, self signed certificates are generated in RouterOS [[Manual:System/Certificates | System/Certificates]] menu. Some certificate requirements should be met to connect various devices to the server:
* Common name should contain IP or DNS name of the server;
* SAN (subject alternative name) should have IP or DNS of the server;
* EKU (extended key usage) tls-server and tls-client are required.
Office1 router:
Considering all requirements above, generate CA and server certificates:
Now that valid certificates are created on the router, add new Phase 1 [[#Profiles | profile]] and Phase 2 [[#Proposals | proposal]] entries with <var>pfs-group=none</var>.
It is important that proposed authentication and encryption algorithms match on both routers. In this example we can use predefined "default" proposal
As we already have proposal as a next step we need correct IpSec policy. We want to encrypt traffic coming form 10.1.202.0/24 to 10.1.101.0/24 and vice versa.
[[#Mode_configs | Mode config]] is used for address distribution from [[Manual:IP/Pools | IP/Pools]].
Since that the policy template must be adjusted to allow only specific network [[#Policies | policies]], it is advised to create a separate policy [[#Groups | group]] and template.
Note that we configured tunnel mode instead of transport, as this is site to site encryption.
====NAT and Fasttrack Bypass====
Create a new IPsec [[#Peers | peer]] entry which will listen to all incoming IKEv2 requests.
At this point if you will try to establish IpSec tunnel it will not work, packets will be rejected. This is because both routers have NAT rules that is changing source address before packet is encrypted. Router is unable to encrypt the packet, because source address do not match address specified in policy configuration. For more information see [[M:Packet_Flow#IPsec_encryption|packet flow ipsec example]].
[[#Identities | Identity]] menu allows to match specific remote peers and assign different configuration for each one of them. First, create a default identity, that will accept all peers, but will verify the peer's identity with its certificate.
{{Note | If you previously tried to establish tunnel before NAT bypass rule was added, you have to clear connection table from existing connection or restart the routers }}
{{Note | If peer's ID (ID_i) is not matching with the certificate it sends, the identity lookup will fail. See <var>remote-id</var> in [[#Identities | identities]] section. }}
It is very important that bypass rule is placed at the top of all other NAT rules.
For example, we want to assign different [[#Mode_configs | mode config]] for user "A", who uses certificate "rw-client1" to authenticate itself to the server. First of all, make sure a new mode config is created and ready to be applied for the specific user.
Another issue is if you have fasttrack enabled, packet bypasses ipsec policies. So we need to add accept rule before fasttrack
However this can add significant load to CPU if there is a fair amount of tunnels and significant traffic on each tunnel.
It is possible apply this configuration for user "A" by using <var>match-by=certificate</var> parameter and specifying his certificate with <var>remote-certificate</var>.
Solution is to use RAW firewall tables to bypass connection tracking, that way eliminating need of filter rules listed above and reducing load on CPU by approximately 30%.
See [[Manual:Interface/L2TP#Basic_L2TP.2FIpSec_setup | L2TP configuration examples]].
Split tunneling is a method which allows road warrior clients to only access a specific secured network and at the same time send the rest of the traffic based on their internal routing table (as opposed to sending all traffic over the tunnel). To configure split tunneling, changes to [[#Mode_configs | mode config]] parameters are needed.
===Allow Only Ipsec Encapsulated Traffic===
For example we will allow our road warrior clients to only access 10.5.8.0/24 network.
There are some scenarios where for security reasons you would like to drop access from/to specific networks if incoming/outgoing packets are not encrypted. For example, If we have L2TP/Ipsec setup we would want to drop non encrypted L2TP connection attempts.
<pre>
/ip ipsec mode-conf
set [find name="rw-conf"] split-include=10.5.8.0/24
</pre>
It is also possible to send specific DNS server for the client to use. By default <var>system-dns=yes</var> is used, which sends DNS servers that are configured on the router itself in [[Manual:IP/DNS | IP/DNS]]. We can force the client to use different DNS server by using the <var>static-dns</var> parameter.
<pre>
/ip ipsec mode-conf
set [find name="rw-conf"] system-dns=no static-dns=10.5.8.1
</pre>
While it is possible to adjust IPsec policy template to only allow road warrior clients to generate [[#Policies | policies]] to network configured by <var>split-include</var> parameter, this can cause compatibility issues with different vendor implementations (see [[#Known_limitations | known limitations]]). Instead of adjusting the policy template, allow access to secured network in [[Manual:IP/Firewall/Filter | IP/Firewall/Filter]] and drop everything else.
* By setting DSCP or priority in mangle and matching the same values in firewall after decapsulation.
</pre>
A file named <i>cert_export_rw-client1.p12</i> is now located in the routers [[Manual:System/File | System/File]] section. This file should be securely transported to the client device.
====Ipsec Policy Matcher====
Typically PKCS12 bundle contains also CA certificate, but some vendors may not install this CA, so self-signed CA certificate must be exported separately using PEM format.
Lets set up ipsec policy matcher to accept all packets that matched any of ipsec policies and drop the rest
A file named <i>cert_export_ca.crt</i> is now located in the routers [[Manual:System/File | System/File]] section. This file should also be securely transported to the client device.
<b>PEM</b> is another certificate format for use in client software that do not support PKCS12. Principle is pretty much the same.
Three files are now located in the routers Files section: <i>cert_export_ca.crt</i>, <i>cert_export_rw-client1.crt</i> and <i>cert_export_rw-client1.key</i> which should be securely transported to the client device.
=====Known limitations=====
Here is a list of known limitations by popular client software IKEv2 implementations.
* Windows will always ignore networks received by <var>split-include</var> and request policy with destination 0.0.0.0/0 (TSr). When IPsec-SA is generated, Windows requests DHCP option 249 to which RouterOS will respond with configured <var>split-include</var> networks automatically.
* Both Apple macOS and iOS will only accept the first <var>split-include</var> network.
* Both Apple macOS and iOS will use the DNS servers from <var>system-dns</var> and <var>static-dns</var> parameters only when 0.0.0.0/0 <var>split-include</var> is used.
* While some implementations can make use of different PFS group for phase 2, it is advised to use <var>pfs-group=none</var> under [[#Proposals | proposals]] to avoid any compatibility issues.
There should now be the self-signed CA certificate and the client certificate in Certificate menu. Find out the name of the client certificate.
<pre>
/certificate print
</pre>
<b>cert_export_RouterOS_client.p12_0</b> is the client certificate.
It is advised to create a separate Phase 1 [[#Profiles | profile]] and Phase 2 [[#Proposals | proposal]] configurations to not interfere with any existing IPsec configuration.
<pre>
/ip ipsec profile
add name=ike2-rw
/ip ipsec proposal
add name=ike2-rw pfs-group=none
</pre>
While it is possible to use the default [[#Policies | policy]] template for policy generation, it is better to create a new policy [[#Groups | group]] and template to separate this configuration from any other IPsec configuration.
<pre>
/ip ipsec policy group
add name=ike2-rw
/ip ipsec policy
add group=ike2-rw proposal=ike2-rw template=yes
</pre>
Create a new [[#Mode_configs | mode config]] entry with <var>responder=no</var> that will request configuration parameters from the server.
<pre>
/ip ipsec mode-config
add name=ike2-rw responder=no
</pre>
Lastly, create [[#Peers | peer]] and [[#Identities | identity]] configurations.
If we look at the generated dynamic [[#Policies | policies]], we see that only traffic with a specific (received by [[#Mode_configs | mode config]]) source address will be sent through the tunnel. But a router in most cases will need to route a specific device or network through the tunnel. In such case we can use source NAT to change the source address of packets to match the mode config address. Since the mode config address is dynamic, it is impossible to create static source NAT rule. In RouterOS it is possible to generate dynamic source NAT rules for mode config clients.
[[file:Ipsec-road-warrior-client.png]]
For example, we have a local network 192.168.88.0/24 behind the router and we want all traffic from this network to be sent over the tunnel. First of all, we have to make a new [[M:IP/Firewall/Address_list | IP/Firewall/Address list]] which consists of our local network.
<pre>
/ip firewall address-list
add address=192.168.88.0/24 list=local
</pre>
When it is done, we can assign newly created [[M:IP/Firewall/Address_list | IP/Firewall/Address list]] to [[#Mode_configs | mode config]] configuration.
<pre>
/ip ipsec mode-config
set [ find name=ike2-rw ] src-address-list=local
</pre>
Verify correct source NAT rule is dynamically generated when the tunnel is established.
{{Warning | Make sure dynamic [[#Mode_configs | mode config]] address is not a part of local network. }}
==== Windows client configuration ====
Open PKCS12 format certificate file on the Windows computer. Install the certificate by following the instructions. Make sure you select Local Machine store location.
[[File:Ike2v2_cert_win.png | 1300px]]
You can now proceed to Network and Internet settings -> VPN and add a new configuration. Fill in the Connection name, Server name or address parameters. Select IKEv2 under VPN type. When it is done, it is necessary to select "Use machine certificates". This can be done in Network and Sharing Center by clicking the Properties menu for the VPN connection. The setting is located under Security tab.
[[File:Ike2v2_conf_win.png | 1300px]]
Currently Windows 10 is compatible with the following Phase 1 ([[#Profiles | profiles]]) and Phase 2 ([[#Proposals | proposals]]) proposal sets:
Open PKCS12 format certificate file on the macOS computer and install the certificate in "System" keychain. It is necessary to mark the CA certificate as trusted manually since it is self-signed. Locate the certificate macOS Keychain Access app under System tab and mark it as Always Trust.
[[File:Ikev2_cert_macos.png | 900px]]
You can now proceed to System Preferences -> Network and add a new configuration by clicking the + button. Select Interface: VPN, VPN Type: IKEv2 and name your connection. Remote ID must be set equal to common-name or subjAltName of server's certificate. Local ID can be left blank. Under Authentication Settings select None and choose the client certificate. You can now test the connectivity.
[[File:Ikev2_conf_macos.png | 900px]]
Currently macOS is compatible with the following Phase 1 ([[#Profiles | profiles]]) and Phase 2 ([[#Proposals | proposals]]) proposal sets:
Typically PKCS12 bundle contains also CA certificate, but iOS does not install this CA, so self-signed CA certificate must be installed separately using PEM format. Open these files on the iOS device and install both certificates by following the instructions. It is necessary to mark the self-signed CA certificate as trusted on the iOS device. This can be done in Settings -> General -> About -> Certificate Trust Settings menu. When it is done, check whether both certificates are marked as "verified" under Settings -> General -> Profiles menu.
[[File:Ikev2_cert_ios.PNG | 900px]]
You can now proceed to Settings -> General -> VPN menu and add a new configuration. Remote ID must be set equal to common-name or subjAltName of server's certificate. Local ID can be left blank.
[[File:Ikev2_conf_ios.PNG | 450px]]
Currently iOS is compatible with the following Phase 1 ([[#Profiles | profiles]]) and Phase 2 ([[#Proposals | proposals]]) proposal sets:
Currently there is no IKEv2 native support in Android, however it is possible to use strongSwan from Google Play Store which brings IKEv2 to Android. StrongSwan accepts PKCS12 format certificates, so before setting up the VPN connection in strongSwan, make sure you download the PKCS12 bundle to your Android device. When it is done, create a new VPN profile in strongSwan, type in the server IP and choose "IKEv2 Certificate" as VPN Type. When selecting a User certificate, press Install and follow the certificate extract procedure by specifying the PKCS12 bundle. Save the profile and test the connection by pressing on the VPN profile.
[[file:Ikev2_conf_android.png | 1080px]]
It is possible to specify custom encryption settings in strongSwan by ticking the "Show advanced settings" checkbox. Currently strongSwan by default is compatible with the following Phase 1 ([[#Profiles | profiles]]) and Phase 2 ([[#Proposals | proposals]]) proposal sets:
Download the PKCS12 certificate bundle and move it to /etc/ipsec.d/private directory.
Add exported passphrase for the private key to /etc/ipsec.secrets file where "strongSwan_client.p12" is the file name and "1234567890" is the passphrase.
<pre>
: P12 strongSwan_client.p12 "1234567890"
</pre>
Add a new connection to /etc/ipsec.conf file
<pre>
conn "ikev2"
keyexchange=ikev2
ike=aes128-sha1-modp2048
esp=aes128-sha1
leftsourceip=%modeconfig
leftcert=strongSwan_client.p12
leftfirewall=yes
right=2.2.2.2
rightid="CN=2.2.2.2"
rightsubnet=0.0.0.0/0
auto=add
</pre>
You can now restart (or start) the ipsec daemon and initialize the connection
<pre>
$ ipsec restart
$ ipsec up ikev2
</pre>
===Road Warrior setup with Mode Conf===
Consider setup where worker need to access other co-workers (workstations) and local office server remotely.
Office has two subnets:
* 192.168.55.0/24 for workstations
* 192.168.66.0/24 network that must not be reachable by RoadWarrior clients
* 10.5.8.0/24 for servers
And access to those networks should be secure.
[[file:ipsec-road-warrior.png]]
Typically in RoadWarrior setups as this it is impossible to know from which address user will connect, so we need to set up <var>generate-policy</var> parameter on the server side. However this leads to other problems, client can generate any policy and access any network in the office. Even set 0.0.0.0/0 and deny internet access to office workers.
'''Mode Conf''', '''policy group''' and '''policy templates''' will allow us to overcome these problems.
====IPsec Server Config====
At first we need a pool from which RoadWarrior will will get an address. Typically in office you set up DHCP server for local workstations, the same DHCP pool can be used.
For iOS devices to be able to connect, '''proposal''' changes are needed:
* does not work with 3des encryption algorithm, '''aes-128/256''' works
* auth algorithm must be '''sha1'''
* PFS group must be '''none'''
* lifetime must be '''8 hours'''
Example of valid proposal configuration for iOS devices:
<pre>
/ip ipsec proposal
set default enc-algorithms=aes-128-cbc,aes-256-cbc lifetime=8h \
pfs-group=none
</pre>
{{ Note | Iphone does not work with split-include 0.0.0.0/0. If you set 0.0.0.0/0 for older clients traffic will not be sent over the tunnel, for newer ios clients tunnel will not be established.}}
==== Android Client Notes ====
Android devices are trying to add policy with destination 0.0.0.0/0, so you have to make sure that correct policy template is added.
This example demonstrates how to easily setup L2TP/IPsec server on RouterOS for road warrior connections (works with Windows, Android, iOS, macOS and other vendor L2TP/IPsec implementations).
====RouterOS server configuration====
First step is to enable L2TP server:
<pre>
/interface l2tp-server server
set enabled=yes use-ipsec=required ipsec-secret=mySecret default-profile=default
</pre>
<var>use-ipsec</var> is set to <b>required</b> to make sure that only IPsec encapsulated L2TP connections are accepted.
Now what it does is enables L2TP server and creates dynamic IPsec peer with specified secret.
<pre>
[admin@MikroTik] /ip ipsec peer> print
0 D address=0.0.0.0/0 local-address=0.0.0.0 passive=yes port=500
It will automatically create dynamic IPsec peer and policy configuration.
===Site to Site GRE tunnel over IPsec (IKEv2) using DNS===
This example explains how it is possible to establish a secure and encrypted GRE tunnel between two RouterOS devices when one or both sites do not have a static IP address. Before making this configuration possible, it is necessary to have a DNS name assigned to one of the devices which will act as a responder (server). For simplicity, we will use RouterOS built in DDNS service [[Manual:IP/Cloud | IP/Cloud]].
[[file:Site-to-site-gre-over-ipsec-example.png]]
====Site 1 (server) configuration====
This is the side that will listen to incoming connections and act as a responder. We will use [[#Mode_configs | mode config]] to provide an IP address for the second site, but first create a loopback (blank) bridge and assign an IP address to it that will be used later for GRE tunnel establishment.
<pre>
/interface bridge
add name=loopback
/ip address
add address=192.168.99.1 interface=loopback
</pre>
Continuing with the IPsec configuration, start off by creating new Phase 1 [[#Profiles | profile]] and Phase 2 [[#Proposals | proposal]] entries using stronger or weaker encryption parameters that suits your needs. Note that this configuration example will listen to all incoming IKEv2 requests, meaning the profile configuration will be shared between all other configurations (e.g. RoadWarrior).
Next, create new [[#Mode_configs | mode config]] entry with <var>responder=yes</var>. This will provide an IP configuration for the other site as well as the host (loopback address) for policy generation.
The next step is to create [[#Peers | peer]] configuration that will listen for all IKEv2 requests. If you already have such entry, you can skip this step.
Similarly to server configuration, start off by creating new Phase 1 [[#Profiles | profile]] and Phase 2 [[#Proposals | proposal]] configurations. Since this side will be the initiator, we can use more specific profile configuration to control which exact encryption parameters are used, just make sure they overlap with what is configured on the server side.
Next, create new [[#Mode_configs | mode config]] entry with <var>responder=no</var>. This will make sure the peer requests IP and split-network configuration from the server.
<pre>
/ip ipsec mode-config
add name=ike2-gre responder=no
</pre>
It is also advised to create a new [[#Groups | policy group]] to separate this configuration from any existing or future IPsec configuration.
<pre>
/ip ipsec policy group
add name=ike2-gre
</pre>
Create a new [[#Policies | policy]] template on the client side as well.
Move on to [[#Peers | peer]] configuration. Now we can specify the DNS name for the server under <var>address</var> parameter. Obviously, you can use an IP address as well.
Ipsec policy matcher takes two parameters direction, policy. We used incoming direction and ipsec policy. Ipsec policy option allows us to inspect packets after decapsulation, so for example if we want to allow only gre encapsulated packet from specific source address and drop the rest we could set up following rules
Lastly, create an [[#Identities | identity]] for our newly created peer.
0 T * group=default src-address=::/0 dst-address=::/0 protocol=all proposal=default template=yes
</pre>
====Using generic Ipsec Policy====
1 T group=ike2-gre src-address=192.168.99.2/32 dst-address=192.168.99.1/32 protocol=all proposal=ike2-gre template=yes
The trick of this method is to add default policy with action drop. Lets assume we are running L2TP/IpSec server 1.1.1.1 with public address and we want to drop all non encrypted L2TP:
2 DA src-address=192.168.99.2/32 src-port=any dst-address=192.168.99.1/32 dst-port=any protocol=all action=encrypt level=unique ipsec-protocols=esp
Now router will drop any L2TP unencrypted incoming traffic, but after successful L2TP/Ipsec connection dynamic policy is created with higher priority than it is on default static rule and packets matching that dynamic rule can be forwarded.
A secure tunnel is now established between both sites which will encrypt all traffic between 192.168.99.2 <=> 192.168.99.1 addresses. We can use these addresses to create a GRE tunnel.
{{ Note | Starting from RouterOS 6.40 policy order is important. For this to work, make sure the static drop policy is below the dynamic policies. Move it below the policy template if necessary. }}
<pre>
<pre>
[admin@rack2_10g1] /ip ipsec policy> print
/interface gre
Flags: T - template, X - disabled, D - dynamic, I - inactive, * - default
===Connecting with Shrew Client and allowing only Encrypted traffic===
===IKEv2 EAP between NordVPN and RouterOS===
* [[IPSEC_between_Mikrotik_router_and_a_Shrew_client | See example here]]
[[IKEv2_EAP_between_NordVPN_and_RouterOS | Example available here]]
==Troubleshooting/FAQ==
==Troubleshooting/FAQ==
Line 2,143:
Line 2,969:
;"phase1 negotiation failed due to time up" what does it mean?
;"phase1 negotiation failed due to time up" what does it mean?
:There are communication problems between the peers. Possible causes include - misconfigured Phase 1 IP addresses; firewall blocking UDP ports 500 and 4500; NAT between peers not properly translating IPsec negotiation packets.
:There are communication problems between the peers. Possible causes include - misconfigured Phase 1 IP addresses; firewall blocking UDP ports 500 and 4500; NAT between peers not properly translating IPsec negotiation packets.
:This error message can also appear when <var>local-address</var> parameter is not used properly. More information available [[#Manually_specifying_local-address_parameter_under_Peer_configuration | here]].
;Random packet drops or connections over the tunnel is very slow, enabling packet sniffer/torch fixes the problem
;Random packet drops or connections over the tunnel is very slow, enabling packet sniffer/torch fixes the problem
:Problem is that before encapsulation packets are sent to fasttrack/fastpath, thus bypassing ipsec policy.
:Problem is that before encapsulation packets are sent to Fasttrack/FastPath, thus bypassing IPsec policy checking.
:Solution is to exclude traffic that need to be encapsulated/decaplsulated from fasttrack, see configuration example [[#NAT_and_Fasttrack_Bypass | here]].
:Solution is to exclude traffic that need to be encapsulated/decaplsulated from Fasttrack, see configuration example [[#NAT_and_Fasttrack_Bypass | here]].
;How to enable ike2?
;How to enable ike2?
: For basic configuration enabling ike2 is very simple, just change <var>exchange-mode</var> in peer settings to <b>ike2</b>
: For basic configuration enabling ike2 is very simple, just change <var>exchange-mode</var> in peer settings to <b>ike2</b>.
; fatal NO-PROPOSAL-CHOSEN notify messsage
; fatal NO-PROPOSAL-CHOSEN notify messsage
Line 2,158:
Line 2,985:
; Can I allow only encrypted traffic?
; Can I allow only encrypted traffic?
: Yes, you can, see examples [[#Allow_Only_Ipsec_Encapsulated_Traffic | here]].
: Yes, you can, see examples [[#Allow_only_IPsec_encapsulated_traffic | here]].
; I enable IKEv2 REAUTH on StrongSwan and got error 'initiator did not reauthenticate as requested'
: RouterOS does not support rfc4478, reauth must be disabled on StrongSwan.
Internet Protocol Security (IPsec) is a set of protocols defined by the Internet Engineering Task Force (IETF) to secure packet exchange over unprotected IP/IPv6 networks such as Internet.
IPsec protocol suite can be divided in following groups:
Internet Key Exchange (IKE) protocols. Dynamically generates and distributes cryptographic keys for AH and ESP.
Authentication Header (AH) RFC 4302
Encapsulating Security Payload (ESP) RFC 4303
Internet Key Exchange Protocol (IKE)
The Internet Key Exchange (IKE) is a protocol that provides authenticated keying material for Internet Security Association and Key Management Protocol (ISAKMP) framework. There are other key exchange schemes that work with ISAKMP, but IKE is the most widely used one. Together they provide means for authentication of hosts and automatic management of security associations (SA).
Most of the time IKE daemon is doing nothing. There are two possible situations when it is activated:
There is some traffic caught by a policy rule which needs to become encrypted or authenticated, but the policy doesn't have any SAs. The policy notifies IKE daemon about that, and IKE daemon initiates connection to remote host.
IKE daemon responds to remote connection.
In both cases, peers establish connection and execute 2 phases:
Phase 1 - The peers agree upon algorithms they will use in the following IKE messages and authenticate. The keying material used to derive keys for all SAs and to protect following ISAKMP exchanges between hosts is generated also. This phase should match following settings:
authentication method
DH group
encryption algorithm
exchange mode
hash alorithm
NAT-T
DPD and lifetime (optional)
Phase 2 - The peers establish one or more SAs that will be used by IPsec to encrypt data. All SAs established by IKE daemon will have lifetime values (either limiting time, after which SA will become invalid, or amount of data that can be encrypted by this SA, or both). This phase should match following settings:
Ipsec protocol
mode (tunnel or transport)
authentication method
PFS (DH) group
lifetime
Note: There are two lifetime values - soft and hard. When SA reaches it's soft lifetime treshold, the IKE daemon receives a notice and starts another phase 2 exchange to replace this SA with fresh one. If SA reaches hard lifetime, it is discarded.
Warning: Phase 1 is not re-keyed if DPD is disabled when lifetime expires, only phase 2 is re-keyed. To force phase 1 re-key, enable DPD.
Warning: PSK authentication was known to be vulnerable against Offline attacks in "aggressive" mode, however recent discoveries indicate that offline attack is possible also in case of "main" and "ike2" exchange modes. General recommendation is to avoid using PSK authentication method.
IKE can optionally provide a Perfect Forward Secrecy (PFS), which is a property of key exchanges, that, in turn, means for IKE that compromising the long term phase 1 key will not allow to easily gain access to all IPsec data that is protected by SAs established through this phase 1. It means an additional keying material is generated for each phase 2.
Generation of keying material is computationally very expensive. Exempli gratia, the use of modp8192 group can take several seconds even on very fast computer. It usually takes place once per phase 1 exchange, which happens only once between any host pair and then is kept for long time. PFS adds this expensive operation also to each phase 2 exchange.
Diffie-Hellman Groups
Diffie-Hellman (DH) key exchange protocol allows two parties without any initial shared secret to create one securely. The following Modular Exponential (MODP) and Elliptic Curve (EC2N) Diffie-Hellman (also known as "Oakley") Groups are supported:
To avoid problems with IKE packets hit some SPD rule and require to encrypt it with not yet established SA (that this packet perhaps is trying to establish), locally originated packets with UDP source port 500 are not processed with SPD. The same way packets with UDP destination port 500 that are to be delivered locally are not processed in incoming policy check.
Setup Procedure
To get IPsec to work with automatic keying using IKE-ISAKMP you will have to configure policy, peer and proposal (optional) entries.
Warning: Ipsec is very sensitive to time changes. If both ends of the IpSec tunnel are not synchronizing time equally(for example, different NTP servers not updating time with the same timestamp), tunnels will break and will have to be established again.
EAP Authentication methods
Outer Auth
Inner Auth
EAP-GTC
EAP-MD5
EAP-MSCHAPv2
EAP-PEAPv0
EAP-MSCHAPv2
EAP-GPSK
EAP-GTC
EAP-MD5
EAP-TLS
EAP-SIM
EAP-TLS
EAP-TTLS
PAP
CHAP
MS-CHAP
MS-CHAPv2
EAP-MSCHAPv2
EAP-GTC
EAP-MD5
EAP-TLS
EAP-TLS on Windows is called "Smart Card or other certificate".
Authentication Header (AH)
AH is a protocol that provides authentication of either all or part of the contents of a datagram through the addition of a header that is calculated based on the values in the datagram. What parts of the datagram are used for the calculation, and the placement of the header, depends whether tunnel or transport mode is used.
The presence of the AH header allows to verify the integrity of the message, but doesn't encrypt it. Thus, AH provides authentication but not privacy. Another protocol (ESP) is considered superior, it provides data privacy and also its own authentication method.
RouterOS supports the following authentication algorithms for AH:
SHA2 (256, 512)
SHA1
MD5
Transport mode
In transport mode AH header is inserted after IP header. IP data and header is used to calculate authentication value. IP fields that might change during transit, like TTL and hop count, are set to zero values before authentication.
Tunnel mode
In tunnel mode original IP packet is encapsulated within a new IP packet. All of the original IP packet is authenticated.
Encapsulating Security Payload (ESP)
Encapsulating Security Payload (ESP) uses shared key encryption to provide data privacy. ESP also supports its own authentication scheme like that used in AH.
ESP packages its fields in a very different way than AH. Instead of having just a header, it divides its fields into three components:
ESP Header - Comes before the encrypted data and its placement depends on whether ESP is used in transport mode or tunnel mode.
ESP Trailer - This section is placed after the encrypted data. It contains padding that is used to align the encrypted data.
ESP Authentication Data - This field contains an Integrity Check Value (ICV), computed in a manner similar to how the AH protocol works, for when ESP's optional authentication feature is used.
Transport mode
In transport mode ESP header is inserted after original IP header. ESP trailer and authentication value is added to the end of the packet. In this mode only IP payload is encrypted and authenticated, IP header is not secured.
Tunnel mode
In tunnel mode original IP packet is encapsulated within a new IP packet thus securing IP payload and IP header.
Encryption algorithms
RouterOS ESP supports various encryption and authentication algorithms.
Authentication:
MD5
SHA1
SHA2 (256-bit, 512-bit)
Encryption:
AES - 128-bit, 192-bit and 256-bit key AES-CBC, AES-CTR and AES-GCM algorithms;
Blowfish - added since v4.5
Twofish - added since v4.5
Camellia - 128-bit, 192-bit and 256-bit key Camellia encryption algorithm added since v4.5
DES - 56-bit DES-CBC encryption algorithm;
3DES - 168-bit DES encryption algorithm;
Hardware acceleration
Hardware acceleration allows to do faster encryption process by using built-in encryption engine inside CPU.
** only manufactured since 2016, serial numbers that begin with number 5 and 7
*** AES-CBC and AES-CTR only encryption is accelerated, hashing done in software
**** DES is not supported, only 3DES and AES-CBC
IPsec throughput results of various encryption and hash algorithm combinations are published on MikroTik products page. When testing throughput, please follow the guidelines available in the Traffic Generator manual page
Policies
Sub-menu:/ip ipsec policy
Policy table is used to determine whether security settings should be applied to a packet.
Specifies what to do with packet matched by the policy.
none - pass the packet unchanged.
discard - drop the packet.
encrypt - apply transformations specified in this policy and it's SA.
comment (string; Default: )
Short description of the policy.
disabled (yes | no; Default: no)
Whether policy is used to match packets.
dst-address (IP/IPv6 prefix; Default: 0.0.0.0/32)
Destination address to be matched in packets. Applicable when tunnel mode (tunnel=yes) or template (template=yes) is used.
dst-port (integer:0..65535 | any; Default: any)
Destination port to be matched in packets. If set to any all ports will be matched.
group (string; Default: default)
Name of the policy group to which this template is assigned.
ipsec-protocols (ah | esp; Default: esp)
Specifies what combination of Authentication Header and Encapsulating Security Payload protocols you want to apply to matched traffic.
level (require | unique | use; Default: require)
Specifies what to do if some of the SAs for this policy cannot be found:
use - skip this transform, do not drop packet and do not acquire SA from IKE daemon;
require - drop packet and acquire SA;
unique - drop packet and acquire a unique SA that is only used with this particular policy. It is used in setups where multiple clients can sit behind one public IP address (clients behind NAT).
Source address to be matched in packets. Applicable when tunnel mode (tunnel=yes) or template (template=yes) is used.
src-port (any | integer:0..65535; Default: any)
Source port to be matched in packets. If set to any all ports will be matched.
template (yes | no; Default: no)
Creates a template and assigns it to specified policy group.
Following parameters are used by template:
group - name of the policy group to which this template is assigned;
src-address, dst-address - Requested subnet must match in both directions(for example 0.0.0.0/0 to allow all);
protocol - protocol to match, if set to all, then any protocol is accepted;
proposal - SA parameters used for this template;
level - useful when unique is required in setups with multiple clients behind NAT.
tunnel (yes | no; Default: no)
Specifies whether to use tunnel mode.
Read only properties
Property
Description
active (yes | no)
Whether this policy is currently in use.
default (yes | no)
Whether this is a default system entry.
dynamic (yes | no)
Whether this is a dynamically added or generated entry.
invalid (yes | no)
Whether this policy is invalid - possible cause is duplicate policy with the same src-address and dst-address.
ph2-count (integer)
Number of active phase 2 sessions associated with the policy.
ph2-state (expired | no-phase2 | established)
Indication of the progress of key establishing.
sa-dst-address (ip/ipv6 address; Default: ::)
SA destination IP/IPv6 address (remote peer).
sa-src-address (ip/ipv6 address; Default: ::)
SA source IP/IPv6 address (local peer).
Warning: policy order is important starting form v6.40. Now it works similar as firewall filters where policies are executed from top to bottom (priority parameter is removed).
Note:
All packets are IPIP encapsulated in tunnel mode, and their new IP header's src-address and dst-address are set to sa-src-address and sa-dst-address values of this policy. If you do not use tunnel mode (id est you use transport mode), then only packets whose source and destination addresses are the same as sa-src-address and sa-dst-address can be processed by this policy. Transport mode can only work with packets that originate at and are destined for IPsec peers (hosts that established security associations). To encrypt traffic between networks (or a network and a host) you have to use tunnel mode.
Statistics
Sub-menu:/ip ipsec statistics
This menu shows various IPsec statistics and errors.
Read only properties
Property
Description
in-errors (integer)
All inbound errors that are not matched by other counters.
in-buffer-errors (integer)
No free buffer.
in-header-errors (integer)
Header error.
in-no-states (integer)
No state is found i.e. either inbound SPI, address, or IPsec protocol at SA is wrong.
in-state-protocol-errors (integer)
Transformation protocol specific error, for example SA key is wrong or hardware accelerator is unable to handle amount of packets.
in-state-mode-errors (integer)
Transformation mode specific error.
in-state-sequence-errors (integer)
Sequence number is out of window.
in-state-expired (integer)
State is expired.
in-state-mismatches (integer)
State has mismatched option, for example UDP encapsulation type is mismatched.
in-state-invalid (integer)
State is invalid.
in-template-mismatches (integer)
No matching template for states, e.g. inbound SAs are correct but SP rule is wrong. Possible cause is mismatched sa-source or sa-destination address.
in-no-policies (integer)
No policy is found for states, e.g. inbound SAs are correct but no SP is found.
in-policy-blocked (integer)
Policy discards.
in-policy-errors (integer)
Policy errors.
out-errors (integer)
All outbound errors that are not matched by other counters.
out-bundle-errors (integer)
Bundle generation error.
out-bundle-check-errors (integer)
Bundle check error.
out-no-states (integer)
No state is found.
out-state-protocol-errors (integer)
Transformation protocol specific error.
out-state-mode-errors (integer)
Transformation mode specific error.
out-state-sequence-errors (integer)
Sequence errors, for example sequence number overflow.
out-state-expired (integer)
State is expired.
out-policy-blocked (integer)
Policy discards.
out-policy-dead (integer)
Policy is dead.
out-policy-errors (integer)
Policy error.
Proposals
Sub-menu:/ip ipsec proposal
Proposal information that will be sent by IKE daemons to establish SAs for certain policy.
Diffie-Helman group used for Perfect Forward Secrecy.
Read only properties
Property
Description
default (yes | no)
Whether this is a default system entry.
Groups
Sub-menu:/ip ipsec policy group
In this menu it is possible to create additional policy groups used by policy templates.
Properties
Property
Description
name (string; Default: )
comment (string; Default: )
Peers
Sub-menu:/ip ipsec peer
Peer configuration settings are used to establish connections between IKE daemons. This connection then will be used to negotiate keys and algorithms for SAs. Exchange mode is the only unique identifier between the peers, meaning that there can be multiple peer configurations with the same remote-address as long as different exchange-mode is used.
Properties
Property
Description
address (IP/IPv6 Prefix; Default: 0.0.0.0/0)
If remote peer's address matches this prefix, then the peer configuration is used in authentication and establishment of Phase 1. If several peer's addresses match several configuration entries, the most specific one (i.e. the one with largest netmask) will be used.
comment (string; Default: )
Short description of the peer.
disabled (yes | no; Default: no)
Whether peer is used to match remote peer's prefix.
exchange-mode (aggressive | base | main | ike2; Default: main)
Different ISAKMP phase 1 exchange modes according to RFC 2408.
main mode relaxes rfc2409 section 5.4, to allow pre-shared-key authentication in main mode. ike2 mode enables Ikev2 RFC 7296. Parameters that are ignored by IKEv2 proposal-check, compatibility-options, lifebytes, dpd-maximum-failures, nat-traversal.
local-address (IP/IPv6 Address; Default: )
Routers local address on which Phase 1 should be bounded to.
name (string; Default: )
passive (yes | no; Default: no)
When passive mode is enabled will wait for remote peer to initiate IKE connection. Enabled passive mode also indicates that peer is xauth responder, and disabled passive mode - xauth initiator. When passive mode is disabled peer will try to establish not only phase1, but also phase2 automatically, if policies are configured or created during phase1.
port (integer:0..65535; Default: 500)
Communication port used (when router is initiator) to connect to remote peer in cases if remote peer uses non-default port.
profile (string; Default: default)
Name of the profile template that will be used during IKE negotiation.
send-initial-contact (yes | no; Default: yes)
Specifies whether to send "initial contact" IKE packet or wait for remote side, this packet should trigger removal of old peer SAs for current source address.
Usually in road warrior setups clients are initiators and this parameter should be set to no. Initial contact is not sent if modecfg or xauth is enabled for ikev1.
Read only properties
Property
Description
dynamic (yes | no)
Whether this is a dynamically added entry by different service (e.g L2TP).
responder (yes | no)
Whether this peer will act as a responder only (listen to incoming requests) and not initiate a connection.
Identities
Identities are configuration parameters that are specific to the remote peer. Main purpose of an identity is to handle authentication and verify peer's integrity.
digital-signature - authenticate using a pair of RSA certificates;
eap - IKEv2 EAP authentication for initiator (peer with netmask of /32). Must be used together with eap-methods;
eap-radius - IKEv2 EAP RADIUS passthrough authentication for responder (RFC 3579). Server certificate in this case is required. If server certificate is not specified then only clients supporting EAP-only (RFC 5998) will be able to connect. Note that EAP method should be compatible with EAP-only;
pre-shared-key - authenticate by a password (pre-shared secret) string shared between the peers (not recommended since offline attack on pre-shared key is possible);
rsa-key - authenticate using a RSA key imported in keys menu. Only supported in IKEv1;
pre-shared-key-xauth - authenticate by a password (pre-shared secret) string shared between the peers + XAuth username and password. Only supported in IKEv1;
rsa-signature-hybrid - responder certificate authentication with initiator XAuth. Only supported in IKEv1.
certificate (string; Default: )
Name of a certificate listed in System/Certificates (signing packets; the certificate must have private key). Applicable if digital signature authentication method (auth-method=digital-signature) or EAP (auth-method=eap) is used.
All EAP methods requires whole certificate chain including intermediate and root CA certificates to be present in System/Certificates menu. Also username and password (if required by authentication server) must be specified. Multiple EAP methods may be specified and will be used in specified order. Currently supported EAP methods:
eap-mschapv2;
eap-peap - also known as PEAPv0/EAP-MSCHAPv2;
eap-tls - requires additional client certificate specified under certificate parameter;
eap-ttls.
generate-policy (no | port-override | port-strict; Default: no)
Allow this peer to establish SA for non-existing policies. Such policies are created dynamically for the lifetime of SA. Automatic policies allows, for example, to create IPsec secured L2TP tunnels, or any other setup where remote peer's IP address is not known at the configuration time.
no - do not generate policies;
port-override - generate policies and force policy to use any port (old behavior);
port-strict - use ports from peer's proposal, which should match peer's policy.
key (string; Default: )
Name of the private key from keys menu. Applicable if RSA key authentication method (auth-method=rsa-key) is used.
On initiator, this controls what ID_i is sent to the responder. On responder, this controls what ID_r is sent to the initiator. In IKEv2, responder also expects this ID in received ID_r from initiator.
auto - tries to use correct ID automatically;
address - IP address is used as ID;
fqdn - fully qualified domain name;
key-id - use the specified key ID for the identity;
user fqdn - specifies a fully-qualified username string, for example, "user@domain.com".
notrack-chain (string; Default: )
Adds IP/Firewall/Raw rules matching IPsec policy to specified chain. Use together with generate-policy.
password (string; Default: )
XAuth or EAP password. Applicable if pre-shared key with XAuth authentication method (auth-method=pre-shared-key-xauth) or EAP (auth-method=eap) is used.
If generate-policy is enabled, traffic selectors are checked against templates from the same group. If none of the templates match, Phase 2 SA will not be established.
remote-certificate (string; Default: )
Name of a certificate (listed in System/Certificates) for authenticating the remote side (validating packets; no private key required). If remote-certificate is not specified then received certificate from remote peer is used and checked against CA in certificate menu. Proper CA must be imported in certificate store. If remote-certificate and match-by=certificate is specified, only the specific client certificate will be matched. Applicable if digital signature authentication method (auth-method=digital-signature) is used.
This parameter controls what ID value to expect from the remote peer. Note that all types except for ignore will verify remote peer's ID with received certificate. In case when the peer sends certificate name as its ID, it is checked against the certificate, else the ID is checked against Subject Alt. Name.
auto - accept all ID's;
fqdn - fully qualified domain name. Only supported in IKEv2;
user fqdn - a fully-qualified username string, for example, "user@domain.com". Only supported in IKEv2;
key-id - specific key ID for the identity. Only supported in IKEv2;
ignore - do not verify received ID with certificate (dangerous).
remote-key (string; Default: )
Name of the public key from keys menu. Applicable if RSA key authentication method (auth-method=rsa-key) is used.
secret (string; Default: )
Secret string. If it starts with '0x', it is parsed as a hexadecimal value. Applicable if pre-shared key authentication method (auth-method=pre-shared-key and auth-method=pre-shared-key-xauth) is used.
username (string; Default: )
XAuth or EAP username. Applicable if pre-shared key with XAuth authentication method (auth-method=pre-shared-key-xauth) or EAP (auth-method=eap) is used.
Read only properties
Property
Description
dynamic (yes | no)
Whether this is a dynamically added entry by different service (e.g L2TP).
Profiles
Profiles defines a set of parameters that will be used for IKE negotiation during Phase 1. These parameters may be common with other peer configurations.
Hashing algorithm. SHA (Secure Hash Algorithm) is stronger, but slower. MD5 uses 128-bit key, sha1-160bit key.
lifebytes (Integer: 0..4294967295; Default: 0)
Phase 1 lifebytes is used only as administrative value which is added to proposal. Used in cases if remote peer requires specific lifebytes value to establish phase 1.
lifetime (time; Default: 1d)
Phase 1 lifetime: specifies how long the SA will be valid.
name (string; Default: )
nat-traversal (yes | no; Default: yes)
Use Linux NAT-T mechanism to solve IPsec incompatibility with NAT routers inbetween IPsec peers. This can only be used with ESP protocol (AH is not supported by design, as it signs the complete packet, including IP header, which is changed by NAT, rendering AH signature invalid). The method encapsulates IPsec ESP traffic into UDP streams in order to overcome some minor issues that made ESP incompatible with NAT.
Prefix length (netmask) of assigned address from the pool.
comment (string; Default: )
name (string; Default: )
responder (yes | no; Default: no)
Specifies whether the configuration will work as an initiator (client) or responder (server). Initiator will request for mode-config parameters from responder.
split-include (list of IP prefix; Default: )
List of subnets in CIDR format, which to tunnel. Subnets will be sent to the peer using CISCO UNITY extension, remote peer will create specific dynamic policies.
src-address-list (address list; Default: )
Specifying an address list will generate dynamic source NAT rules. This parameter is only available with responder=no. RoadWarrior client with NAT
static-dns (list of IP; Default: )
Manually specified DNS server's IP address to be sent to the client.
system-dns (yes | no; Default: )
When this option is enabled DNS addresses will be taken from /ip dns.
Read only properties
Property
Description
default (yes | no)
Whether this is a default system entry.
Note: Not all IKE implementations support multiple split networks provided by split-include option.
Note: If RouterOS client is initiator, it will always send CISCO UNITY extension, and RouterOS supports only split-include from this extension.
Note: It is not possible to use system-dns and static-dns at the same time.
Installed SAs
Sub-menu:/ip ipsec installed-sa
This menu provides information about installed security associations including the keys.
Read only properties
Property
Description
AH (yes | no)
Whether AH protocol is used by this SA.
ESP (yes | no)
Whether ESP protocol is used by this SA.
add-lifetime (time/time)
Added lifetime for the SA in format soft/hard:
soft - time period after which ike will try to establish new SA;
Shows the current state of the SA ("mature", "dying" etc)
Commands
Property
Description
flush ()
Manually removes all installed security associations.
Keys
Sub-menu:/ip ipsec key
This menu lists all imported public andprivate keys, that can be used for peer authentication. Menu has several commands to work with keys.
Properties
Property
Description
name (string; Default: )
Read only properties
Property
Description
key-size (1024 | 2048 | 4096)
Size of this key.
private-key (yes | no)
Whether this is a private key.
rsa (yes | no)
Whether this is a RSA key.
Commands
Property
Description
export-pub-key (file-name; key)
Export public key to file from one of existing private keys.
generate-key (key-size; name)
Generate private key. Takes two parameters, name of newly generated key and key size 1024,2048 and 4096.
import (file-name; name)
Import key from file.
Settings
Sub-menu:/ip ipsec settings
Property
Description
accounting (yes | no; Default: )
Whether to send RADIUS accounting requests to RADIUS server. Applicable if EAP Radius (auth-method=eap-radius) or pre-shared key with XAuth authentication method (auth-method=pre-shared-key-xauth) is used.
interim-update (time; Default: )
Interval between each consecutive RADIUS accounting Interim update. Accounting must be enabled.
Consider setup as illustrated below. RouterOS acts as a RoadWarrior client connected to Office allowing access to its internal resources.
Tunnel is established, local mode-config IP address is received and a set of dynamic policies are generated.
[admin@pair_r1] > ip ipsec policy print
Flags: T - template, X - disabled, D - dynamic, I - invalid, A - active, * - default
0 T * group=default src-address=::/0 dst-address=::/0 protocol=all proposal=default template=yes
1 DA src-address=192.168.77.254/32 src-port=any dst-address=10.5.8.0/24 dst-port=any protocol=all
action=encrypt level=unique ipsec-protocols=esp tunnel=yes sa-src-address=10.155.107.8
sa-dst-address=10.155.107.9 proposal=default ph2-count=1
2 DA src-address=192.168.77.254/32 src-port=any dst-address=192.168.55.0/24 dst-port=any protocol=all
action=encrypt level=unique ipsec-protocols=esp tunnel=yes sa-src-address=10.155.107.8
sa-dst-address=10.155.107.9 proposal=default ph2-count=1
Currently only packets with source address of 192.168.77.254/32 will match the IPsec policies. For local network to be able to reach remote subnets, it is necessary to change the source address of local hosts to the dynamically assigned mode config IP address. It is possible to generate source NAT rules dynamically. This can be done by creating a new address list which contains of all local networks that NAT rule should be applied. In our case, it is 192.168.88.0/24.
By specifying the address list under mode-config initiator configuration, a set of source NAT rules will be dynamically generated.
/ip ipsec mode-config set [ find name="request-only" ] src-address-list=local-RW
When the IPsec tunnel is established, we can see the dynamically created source NAT rules for each network. Now every host in 192.168.88.0/24 is able to access Office's internal resources.
[admin@pair_r1] > ip firewall nat print
Flags: X - disabled, I - invalid, D - dynamic
0 D ;;; ipsec mode-config
chain=srcnat action=src-nat to-addresses=192.168.77.254 dst-address=192.168.55.0/24 src-address-list=local-RW
1 D ;;; ipsec mode-config
chain=srcnat action=src-nat to-addresses=192.168.77.254 dst-address=10.5.8.0/24 src-address-list=local-RW
Note: On server side it is mandatory to set passive to yes when XAuth is used.
Allow only IPsec encapsulated traffic
There are some scenarios where for security reasons you would like to drop access from/to specific networks if incoming/outgoing packets are not encrypted. For example, if we have L2TP/IPsec setup we would want to drop non encrypted L2TP connection attempts.
There are several ways how to achieve this:
Using IPsec policy matcher in firewall;
Using generic IPsec policy with action set to drop and lower priority (can be used in Road Warrior setups where dynamic policies are generated);
By setting DSCP or priority in mangle and matching the same values in firewall after decapsulation.
IPsec policy matcher
Lets set up IPsec policy matcher to accept all packets that matched any of IPsec policies and drop the rest:
IPsec policy matcher takes two parameters direction,policy. We used incoming direction and IPsec policy. IPsec policy option allows us to inspect packets after decapsulation, so for example if we want to allow only gre encapsulated packet from specific source address and drop the rest we could set up following rules:
The trick of this method is to add default policy with action drop. Lets assume we are running L2TP/IPsec server on public 1.1.1.1 address and we want to drop all non encrypted L2TP:
Now router will drop any L2TP unencrypted incoming traffic, but after successful L2TP/IPsec connection dynamic policy is created with higher priority than it is on default static rule and packets matching that dynamic rule can be forwarded.
Note: Policy order is important! For this to work, make sure the static drop policy is below the dynamic policies. Move it below the policy template if necessary.
[admin@rack2_10g1] /ip ipsec policy> print
Flags: T - template, X - disabled, D - dynamic, I - inactive, * - default
0 T * group=default src-address=::/0 dst-address=::/0 protocol=all
proposal=default template=yes
1 D src-address=1.1.1.1/32 src-port=1701 dst-address=10.5.130.71/32
dst-port=any protocol=udp action=encrypt level=require
ipsec-protocols=esp tunnel=no sa-src-address=1.1.1.1
sa-dst-address=10.5.130.71
2 src-address=1.1.1.1/32 src-port=1701 dst-address=0.0.0.0/0
dst-port=any protocol=udp action=discard level=unique
ipsec-protocols=esp tunnel=yes sa-src-address=1.1.1.1
sa-dst-address=0.0.0.0 proposal=default manual-sa=none
Manually specifying local-address parameter under Peer configuration
Using different routing table
IPsec, as any other service in RouterOS, uses main routing table regardless what local-address parameter is used for Peer configuration. It is necessary to apply routing marks to both IKE and IPSec traffic.
Consider the following example. There are two default routes - one in main routing table and another in routing table "backup". It is necessary to use the backup link for IPsec site to site tunnel.
[admin@pair_r1] > /ip route print detail
Flags: X - disabled, A - active, D - dynamic, C - connect, S - static, r - rip, b - bgp, o - ospf, m - mme, B - blackhole, U - unreachable, P - prohibit
0 A S dst-address=0.0.0.0/0 gateway=10.155.107.1 gateway-status=10.155.107.1 reachable via ether1 distance=1 scope=30 target-scope=10 routing-mark=backup
1 A S dst-address=0.0.0.0/0 gateway=172.22.2.115 gateway-status=172.22.2.115 reachable via ether2 distance=1 scope=30 target-scope=10
2 ADC dst-address=10.155.107.0/25 pref-src=10.155.107.8 gateway=ether1 gateway-status=ether1 reachable distance=0 scope=10
3 ADC dst-address=172.22.2.0/24 pref-src=172.22.2.114 gateway=ether2 gateway-status=ether2 reachable distance=0 scope=10
4 ADC dst-address=192.168.1.0/24 pref-src=192.168.1.1 gateway=bridge-local gateway-status=ether2 reachable distance=0 scope=10
[admin@pair_r1] > /ip firewall nat print
Flags: X - disabled, I - invalid, D - dynamic
0 chain=srcnat action=masquerade out-interface=ether1 log=no log-prefix=""
1 chain=srcnat action=masquerade out-interface=ether2 log=no log-prefix=""
IPsec peer and policy configurations are created using the backup link's source address, as well as NAT bypass rule for IPsec tunnel traffic.
Currently, we see "phase1 negotiation failed due to time up" errors in the log. It is because IPsec tries to reach the remote peer using the main routing table with incorrect source address. It is necessary to mark UDP/500, UDP/4500 and ipsec-esp packets using Mangle.
Using same routing table with multiple IP addresses
Consider the following example. There are multiple IP addresses from the same subnet on the public interface. Masquerade rule is configured on out-interface. It is necessary to use one of the IP addresses explicitly.
[admin@pair_r1] > /ip address print
Flags: X - disabled, I - invalid, D - dynamic
# ADDRESS NETWORK INTERFACE
0 192.168.1.1/24 192.168.1.0 bridge-local
1 172.22.2.1/24 172.22.2.0 ether1
2 172.22.2.2/24 172.22.2.0 ether1
3 172.22.2.3/24 172.22.2.0 ether1
[admin@pair_r1] > /ip route print
Flags: X - disabled, A - active, D - dynamic, C - connect, S - static, r - rip, b - bgp, o - ospf, m - mme, B - blackhole, U - unreachable, P - prohibit
# DST-ADDRESS PREF-SRC GATEWAY DISTANCE
1 A S 0.0.0.0/0 172.22.2.115 1
3 ADC 172.22.2.0/24 172.22.2.1 ether1 0
4 ADC 192.168.1.0/24 192.168.1.1 bridge-local 0
[admin@pair_r1] /ip firewall nat> print
Flags: X - disabled, I - invalid, D - dynamic
0 chain=srcnat action=masquerade out-interface=ether1 log=no log-prefix=""
IPsec peer and policy configuration is created using one of the public IP addresses.
Currently the phase 1 connection uses a different source address than we specified and "phase1 negotiation failed due to time up" errors are shown in the logs. This is because masquerade is changing the source address of the connection to match pref-src address of the connected route. Solution is to exclude connections from the public IP address from being masqueraded.
Consider setup as illustrated below. Two remote office routers are connected to internet and office workstations are behind NAT. Each office has its own local subnet, 10.1.202.0/24 for Office1 and 10.1.101.0/24 for Office2. Both remote offices needs secure tunnel to local networks behind routers.
Site 1 configuration
Start off by creating new Phase 1 profile and Phase 2 proposal entries using stronger or weaker encryption parameters that suits your needs. It is advised to create separate entries for each menu so that they are unique for each peer in case it is necessary to adjust any of the settings in the future. These parameters must match between the sites or else the connection will not establish.
Continue by configuring a peer. Specify the address of the remote router. This address should be reachable through UDP/500 and UDP/4500 ports, so make sure appropriate actions are taken regarding the router's firewall. Specify the name for this peer as well as the newly created profile.
The next step is to create an identity. For a basic pre-shared key secured tunnel, there is nothing much to set except for a strongsecret and the peer to which this identity applies.
Office 2 configuration is almost identical as Office 1 with proper IP address configuration. Start off by creating new Phase 1 profile and Phase 2 proposal entries.
At this point, the tunnel should be established and two IPsec Security Associations should be created on both routers:
/ip ipsec
active-peers print
installed-sa print
NAT and Fasttrack Bypass
At this point if you try to send traffic over the IPsec tunnel, it will not work, packets will be lost. This is because both routers have NAT rules (masquerade) that is changing source address before packet is encrypted. Router is unable to encrypt the packet, because source address do not match address specified in policy configuration. For more information see IPsec packet flow example.
Note: If you previously tried to establish an IP connection before NAT bypass rule was added, you have to clear connection table from existing connection or restart both routers.
It is very important that bypass rule is placed at the top of all other NAT rules.
Another issue is if you have IP/Fasttrack enabled, packet bypasses IPsec policies. So we need to add accept rule before FastTrack.
However, this can add significant load to router's CPU if there is a fair amount of tunnels and significant traffic on each tunnel.
Solution is to use IP/Firewall/Raw to bypass connection tracking, that way eliminating need of filter rules listed above and reducing load on CPU by approximately 30%.
Road Warrior setup using IKEv2 with RSA authentication
This example explains how to establish a secure IPsec connection between a device connected to the Internet (road warrior client) and a device running RouterOS acting as a server.
RouterOS server configuration
Before configuring IPsec, it is required to set up certificates. It is possible to use a separate Certificate Authority for certificate management, however in this example, self signed certificates are generated in RouterOS System/Certificates menu. Some certificate requirements should be met to connect various devices to the server:
Common name should contain IP or DNS name of the server;
SAN (subject alternative name) should have IP or DNS of the server;
EKU (extended key usage) tls-server and tls-client are required.
Considering all requirements above, generate CA and server certificates:
Identity menu allows to match specific remote peers and assign different configuration for each one of them. First, create a default identity, that will accept all peers, but will verify the peer's identity with its certificate.
Note: If peer's ID (ID_i) is not matching with the certificate it sends, the identity lookup will fail. See remote-id in identities section.
For example, we want to assign different mode config for user "A", who uses certificate "rw-client1" to authenticate itself to the server. First of all, make sure a new mode config is created and ready to be applied for the specific user.
Split tunneling is a method which allows road warrior clients to only access a specific secured network and at the same time send the rest of the traffic based on their internal routing table (as opposed to sending all traffic over the tunnel). To configure split tunneling, changes to mode config parameters are needed.
For example we will allow our road warrior clients to only access 10.5.8.0/24 network.
/ip ipsec mode-conf
set [find name="rw-conf"] split-include=10.5.8.0/24
It is also possible to send specific DNS server for the client to use. By default system-dns=yes is used, which sends DNS servers that are configured on the router itself in IP/DNS. We can force the client to use different DNS server by using the static-dns parameter.
/ip ipsec mode-conf
set [find name="rw-conf"] system-dns=no static-dns=10.5.8.1
While it is possible to adjust IPsec policy template to only allow road warrior clients to generate policies to network configured by split-include parameter, this can cause compatibility issues with different vendor implementations (see known limitations). Instead of adjusting the policy template, allow access to secured network in IP/Firewall/Filter and drop everything else.
A file named cert_export_rw-client1.p12 is now located in the routers System/File section. This file should be securely transported to the client device.
Typically PKCS12 bundle contains also CA certificate, but some vendors may not install this CA, so self-signed CA certificate must be exported separately using PEM format.
/certificate
export-certificate ca type=pem
A file named cert_export_ca.crt is now located in the routers System/File section. This file should also be securely transported to the client device.
PEM is another certificate format for use in client software that do not support PKCS12. Principle is pretty much the same.
/certificate
export-certificate ca
export-certificate rw-client1 export-passphrase=1234567890
Three files are now located in the routers Files section: cert_export_ca.crt, cert_export_rw-client1.crt and cert_export_rw-client1.key which should be securely transported to the client device.
Known limitations
Here is a list of known limitations by popular client software IKEv2 implementations.
Windows will always ignore networks received by split-include and request policy with destination 0.0.0.0/0 (TSr). When IPsec-SA is generated, Windows requests DHCP option 249 to which RouterOS will respond with configured split-include networks automatically.
Both Apple macOS and iOS will only accept the first split-include network.
Both Apple macOS and iOS will use the DNS servers from system-dns and static-dns parameters only when 0.0.0.0/0 split-include is used.
While some implementations can make use of different PFS group for phase 2, it is advised to use pfs-group=none under proposals to avoid any compatibility issues.
While it is possible to use the default policy template for policy generation, it is better to create a new policy group and template to separate this configuration from any other IPsec configuration.
Verify that the connection is successfully established.
/ip ipsec
active-peers print
installed-sa print
Enabling dynamic source NAT rule generation
If we look at the generated dynamic policies, we see that only traffic with a specific (received by mode config) source address will be sent through the tunnel. But a router in most cases will need to route a specific device or network through the tunnel. In such case we can use source NAT to change the source address of packets to match the mode config address. Since the mode config address is dynamic, it is impossible to create static source NAT rule. In RouterOS it is possible to generate dynamic source NAT rules for mode config clients.
For example, we have a local network 192.168.88.0/24 behind the router and we want all traffic from this network to be sent over the tunnel. First of all, we have to make a new IP/Firewall/Address list which consists of our local network.
/ip ipsec mode-config
set [ find name=ike2-rw ] src-address-list=local
Verify correct source NAT rule is dynamically generated when the tunnel is established.
[admin@MikroTik] > /ip firewall nat print
Flags: X - disabled, I - invalid, D - dynamic
0 D ;;; ipsec mode-config
chain=srcnat action=src-nat to-addresses=192.168.77.254 src-address-list=local dst-address-list=!local
Warning: Make sure dynamic mode config address is not a part of local network.
Windows client configuration
Open PKCS12 format certificate file on the Windows computer. Install the certificate by following the instructions. Make sure you select Local Machine store location.
You can now proceed to Network and Internet settings -> VPN and add a new configuration. Fill in the Connection name, Server name or address parameters. Select IKEv2 under VPN type. When it is done, it is necessary to select "Use machine certificates". This can be done in Network and Sharing Center by clicking the Properties menu for the VPN connection. The setting is located under Security tab.
Currently Windows 10 is compatible with the following Phase 1 ( profiles) and Phase 2 ( proposals) proposal sets:
Phase 1
Hash Algorithm
Encryption Algorithm
DH Group
SHA1
3DES
modp1024
SHA256
3DES
modp1024
SHA1
AES-128-CBC
modp1024
SHA256
AES-128-CBC
modp1024
SHA1
AES-192-CBC
modp1024
SHA256
AES-192-CBC
modp1024
SHA1
AES-256-CBC
modp1024
SHA256
AES-256-CBC
modp1024
SHA1
AES-128-GCM
modp1024
SHA256
AES-128-GCM
modp1024
SHA1
AES-256-GCM
modp1024
SHA256
AES-256-GCM
modp1024
Phase 2
Hash Algorithm
Encryption Algorithm
PFS Group
SHA1
AES-256-CBC
none
SHA1
AES-128-CBC
none
SHA1
3DES
none
SHA1
DES
none
SHA1
none
none
macOS client configuration
Open PKCS12 format certificate file on the macOS computer and install the certificate in "System" keychain. It is necessary to mark the CA certificate as trusted manually since it is self-signed. Locate the certificate macOS Keychain Access app under System tab and mark it as Always Trust.
You can now proceed to System Preferences -> Network and add a new configuration by clicking the + button. Select Interface: VPN, VPN Type: IKEv2 and name your connection. Remote ID must be set equal to common-name or subjAltName of server's certificate. Local ID can be left blank. Under Authentication Settings select None and choose the client certificate. You can now test the connectivity.
Currently macOS is compatible with the following Phase 1 ( profiles) and Phase 2 ( proposals) proposal sets:
Phase 1
Hash Algorithm
Encryption Algorithm
DH Group
SHA256
AES-256-CBC
modp2048
SHA256
AES-256-CBC
ecp256
SHA256
AES-256-CBC
modp1536
SHA1
AES-128-CBC
modp1024
SHA1
3DES
modp1024
Phase 2
Hash Algorithm
Encryption Algorithm
PFS Group
SHA256
AES-256-CBC
none
SHA1
AES-128-CBC
none
SHA1
3DES
none
iOS client configuration
Typically PKCS12 bundle contains also CA certificate, but iOS does not install this CA, so self-signed CA certificate must be installed separately using PEM format. Open these files on the iOS device and install both certificates by following the instructions. It is necessary to mark the self-signed CA certificate as trusted on the iOS device. This can be done in Settings -> General -> About -> Certificate Trust Settings menu. When it is done, check whether both certificates are marked as "verified" under Settings -> General -> Profiles menu.
You can now proceed to Settings -> General -> VPN menu and add a new configuration. Remote ID must be set equal to common-name or subjAltName of server's certificate. Local ID can be left blank.
Currently iOS is compatible with the following Phase 1 ( profiles) and Phase 2 ( proposals) proposal sets:
Phase 1
Hash Algorithm
Encryption Algorithm
DH Group
SHA256
AES-256-CBC
modp2048
SHA256
AES-256-CBC
ecp256
SHA256
AES-256-CBC
modp1536
SHA1
AES-128-CBC
modp1024
SHA1
3DES
modp1024
Phase 2
Hash Algorithm
Encryption Algorithm
PFS Group
SHA256
AES-256-CBC
none
SHA1
AES-128-CBC
none
SHA1
3DES
none
Note: If you are connected to the VPN over WiFi, the iOS device can go into sleep mode and disconnect from the network.
Android (strongSwan) client configuration
Currently there is no IKEv2 native support in Android, however it is possible to use strongSwan from Google Play Store which brings IKEv2 to Android. StrongSwan accepts PKCS12 format certificates, so before setting up the VPN connection in strongSwan, make sure you download the PKCS12 bundle to your Android device. When it is done, create a new VPN profile in strongSwan, type in the server IP and choose "IKEv2 Certificate" as VPN Type. When selecting a User certificate, press Install and follow the certificate extract procedure by specifying the PKCS12 bundle. Save the profile and test the connection by pressing on the VPN profile.
It is possible to specify custom encryption settings in strongSwan by ticking the "Show advanced settings" checkbox. Currently strongSwan by default is compatible with the following Phase 1 ( profiles) and Phase 2 ( proposals) proposal sets:
Phase 1
Hash Algorithm
Encryption Algorithm
DH Group
SHA*
AES-*-CBC
modp2048
SHA*
AES-*-CBC
ecp256
SHA*
AES-*-CBC
ecp384
SHA*
AES-*-CBC
ecp521
SHA*
AES-*-CBC
modp3072
SHA*
AES-*-CBC
modp4096
SHA*
AES-*-CBC
modp6144
SHA*
AES-*-CBC
modp8192
SHA*
AES-*-GCM
modp2048
SHA*
AES-*-GCM
ecp256
SHA*
AES-*-GCM
ecp384
SHA*
AES-*-GCM
ecp521
SHA*
AES-*-GCM
modp3072
SHA*
AES-*-GCM
modp4096
SHA*
AES-*-GCM
modp6144
SHA*
AES-*-GCM
modp8192
Phase 2
Hash Algorithm
Encryption Algorithm
PFS Group
none
AES-256-GCM
none
none
AES-128-GCM
none
SHA256
AES-256-CBC
none
SHA512
AES-256-CBC
none
SHA1
AES-256-CBC
none
SHA256
AES-192-CBC
none
SHA512
AES-192-CBC
none
SHA1
AES-192-CBC
none
SHA256
AES-128-CBC
none
SHA512
AES-128-CBC
none
SHA1
AES-128-CBC
none
Linux (strongSwan) client configuration
Download the PKCS12 certificate bundle and move it to /etc/ipsec.d/private directory.
Add exported passphrase for the private key to /etc/ipsec.secrets file where "strongSwan_client.p12" is the file name and "1234567890" is the passphrase.
You can now restart (or start) the ipsec daemon and initialize the connection
$ ipsec restart
$ ipsec up ikev2
Road Warrior setup with Mode Conf
Consider setup where worker need to access other co-workers (workstations) and local office server remotely.
Office has two subnets:
192.168.55.0/24 for workstations
192.168.66.0/24 network that must not be reachable by RoadWarrior clients
10.5.8.0/24 for servers
And access to those networks should be secure.
Typically in RoadWarrior setups as this it is impossible to know from which address user will connect, so we need to set up generate-policy parameter on the server side. However this leads to other problems, client can generate any policy and access any network in the office. Even set 0.0.0.0/0 and deny internet access to office workers.
Mode Conf, policy group and policy templates will allow us to overcome these problems.
IPsec Server Config
At first we need a pool from which RoadWarrior will will get an address. Typically in office you set up DHCP server for local workstations, the same DHCP pool can be used.
/ip pool
add name=ipsec-RW ranges=192.168.77.2-192.168.77.254
Next we need to set up what settings to send to the client using Mode Conf.
For iOS devices to be able to connect, proposal changes are needed:
does not work with 3des encryption algorithm, aes-128/256 works
auth algorithm must be sha1
PFS group must be none
lifetime must be 8 hours
Example of valid proposal configuration for iOS devices:
/ip ipsec proposal
set default enc-algorithms=aes-128-cbc,aes-256-cbc lifetime=8h \
pfs-group=none
Note: Iphone does not work with split-include 0.0.0.0/0. If you set 0.0.0.0/0 for older clients traffic will not be sent over the tunnel, for newer ios clients tunnel will not be established.
Android Client Notes
Android devices are trying to add policy with destination 0.0.0.0/0, so you have to make sure that correct policy template is added.
This example demonstrates how to easily setup L2TP/IPsec server on RouterOS for road warrior connections (works with Windows, Android, iOS, macOS and other vendor L2TP/IPsec implementations).
RouterOS server configuration
First step is to enable L2TP server:
/interface l2tp-server server
set enabled=yes use-ipsec=required ipsec-secret=mySecret default-profile=default
use-ipsec is set to required to make sure that only IPsec encapsulated L2TP connections are accepted.
Now what it does is enables L2TP server and creates dynamic IPsec peer with specified secret.
It will automatically create dynamic IPsec peer and policy configuration.
Site to Site GRE tunnel over IPsec (IKEv2) using DNS
This example explains how it is possible to establish a secure and encrypted GRE tunnel between two RouterOS devices when one or both sites do not have a static IP address. Before making this configuration possible, it is necessary to have a DNS name assigned to one of the devices which will act as a responder (server). For simplicity, we will use RouterOS built in DDNS service IP/Cloud.
Site 1 (server) configuration
This is the side that will listen to incoming connections and act as a responder. We will use mode config to provide an IP address for the second site, but first create a loopback (blank) bridge and assign an IP address to it that will be used later for GRE tunnel establishment.
Continuing with the IPsec configuration, start off by creating new Phase 1 profile and Phase 2 proposal entries using stronger or weaker encryption parameters that suits your needs. Note that this configuration example will listen to all incoming IKEv2 requests, meaning the profile configuration will be shared between all other configurations (e.g. RoadWarrior).
Next, create new mode config entry with responder=yes. This will provide an IP configuration for the other site as well as the host (loopback address) for policy generation.
The server side is now configured and listening to all IKEv2 requests. Please make sure the firewall is not blocking UDP/4500 port.
The last step is to create the GRE interface itself. This can also be done later when IPsec connection is established from the client side.
/interface gre
add local-address=192.168.99.1 name=gre-tunnel1 remote-address=192.168.99.2
Site 2 (client) configuration
Similarly to server configuration, start off by creating new Phase 1 profile and Phase 2 proposal configurations. Since this side will be the initiator, we can use more specific profile configuration to control which exact encryption parameters are used, just make sure they overlap with what is configured on the server side.
If everything was done properly, there should be a new dynamic policy present.
/ip ipsec policy print
Flags: T - template, X - disabled, D - dynamic, I - invalid, A - active, * - default
0 T * group=default src-address=::/0 dst-address=::/0 protocol=all proposal=default template=yes
1 T group=ike2-gre src-address=192.168.99.2/32 dst-address=192.168.99.1/32 protocol=all proposal=ike2-gre template=yes
2 DA src-address=192.168.99.2/32 src-port=any dst-address=192.168.99.1/32 dst-port=any protocol=all action=encrypt level=unique ipsec-protocols=esp
tunnel=yes sa-src-address=172.17.2.1 sa-dst-address=172.17.2.2 proposal=ike2-gre ph2-count=1
A secure tunnel is now established between both sites which will encrypt all traffic between 192.168.99.2 <=> 192.168.99.1 addresses. We can use these addresses to create a GRE tunnel.
/interface gre
add local-address=192.168.99.2 name=gre-tunnel1 remote-address=192.168.99.1
[admin@MikroTik] /log> print
(..)
17:12:32 ipsec,error no suitable proposal found.
17:12:32 ipsec,error 10.5.107.112 failed to get valid proposal.
17:12:32 ipsec,error 10.5.107.112 failed to pre-process ph1 packet (side: 1, status 1).
17:12:32 ipsec,error 10.5.107.112 phase1 negotiation failed.
(..)
Peers are unable to negotiate encryption parameters causing the connection to drop. To solve this issue, enable IPSec debug logs and find out which parameters are proposed by the remote peer and adjust configuration accordingly.
In this example, remote end requires SHA1 to be used as hash algorithm, but MD5 is configured on local router. Setting before the column symbol (:) is configured on the local side, parameter after the column symbol (:) is configured on the remote side.
"phase1 negotiation failed due to time up" what does it mean?
There are communication problems between the peers. Possible causes include - misconfigured Phase 1 IP addresses; firewall blocking UDP ports 500 and 4500; NAT between peers not properly translating IPsec negotiation packets.
This error message can also appear when local-address parameter is not used properly. More information available here.
Random packet drops or connections over the tunnel is very slow, enabling packet sniffer/torch fixes the problem
Problem is that before encapsulation packets are sent to Fasttrack/FastPath, thus bypassing IPsec policy checking.
Solution is to exclude traffic that need to be encapsulated/decaplsulated from Fasttrack, see configuration example here.
How to enable ike2?
For basic configuration enabling ike2 is very simple, just change exchange-mode in peer settings to ike2.
fatal NO-PROPOSAL-CHOSEN notify messsage
Remote peer sent notify that it cannot accept proposed algorithms, to find exact cause of the problem, look at remote peers debug logs or configuration and verify that both client and server have the same set of algorithms.
I can ping only in one direction.
Typical problem in such cases is strict firewall, firewall rules allow to create new connections only in one direction. Solution is to recheck firewall rules, or explicitly accept all traffic that should be encapsulated/decapsulated.
