{{Warning|This manual is moved to https://help.mikrotik.com/docs/display/ROS/IP+Settings}}
__TOC__
__TOC__
Line 47:
Line 49:
{{Mr-arg-table
{{Mr-arg-table
|arg=arp-timeout
|arg=arp-timeout
|type=time
|type=time interval
|default=30s
|default=30s
|desc=Timeout for ARP table entries.
|desc=Sets Linux <b>base_reachable_time</b> (base_reachable_time_ms) on all interfaces that use ARP. Initial validity of ARP entry is picked from interval [timeout/2..3*timeout/2] (default from 15s to 45s) after neighbor was found. Can use postfix ms, s, m, h, d for milliseconds, seconds, minutes, hours or days. if no postfix is set then seconds (s) is used. Parameter <b>DOES NOT</b> represent a time when ARP entry is removed from ARP cache, ARP cache entries can be stored in the cache for up to 10minutes if reference in route cache is created.
}}
{{Mr-arg-table
|arg=icmp-rate-limit
|type=integer [0..4294967295]
|default=10
|desc=Limit the maximum rates for sending ICMP packets whose type matches <var>icmp-rate-mask</var> to specific targets. 0 to disable any limiting, otherwise the minimum space between responses in milliseconds.
}}
}}
{{Mr-arg-table
{{Mr-arg-table
|arg=ip-forwarding
|arg=icmp-rate-mask
|type=[0..FFFFFFFF]
|default=0x1818
|desc=Mask made of ICMP types for which rates are being limited. [http://man7.org/linux/man-pages/man7/icmp.7.html More info in linux man pages]
}}
{{Mr-arg-table
|arg=ip-forward
|type=yes {{!}} no
|type=yes {{!}} no
|default=yes
|default=yes
|desc=Emable/disable packet forwarding between interfaces. Resets all configuration parameters to defaults according to RFC1812 for routers.
|desc=Enable/disable packet forwarding between interfaces. Resets all configuration parameters to defaults according to RFC1812 for routers.
}}
}}
{{Mr-arg-table
{{Mr-arg-table
|arg=rp_filter
|arg=rp-filter
|type=loose {{!}} no {{!}} strict
|type=loose {{!}} no {{!}} strict
|default=no
|default=no
Line 68:
Line 84:
* loose - Loose mode as defined in RFC3704 Loose Reverse Path. Each incoming packet's source address is also tested against the FIB and if the source address is not reachable via any interface the packet check will fail.
* loose - Loose mode as defined in RFC3704 Loose Reverse Path. Each incoming packet's source address is also tested against the FIB and if the source address is not reachable via any interface the packet check will fail.
Current recommended practice in RFC3704 is to enable strict mode to prevent IP spoofing from DDos attacks. If using asymmetric routing or other complicated routing, then loose mode is recommended.
Current recommended practice in RFC3704 is to enable strict mode to prevent IP spoofing from DDoS attacks. If using asymmetric routing or other complicated routing or VRRP, then loose mode is recommended.{{Warning | strict mode does not work with routing tables}}
}}
}}
Line 86:
Line 102:
{{Mr-arg-table
{{Mr-arg-table
|arg=arp-timeout
|arg=tcp-syncookies
|type=time interval
|type=yes {{!}} no
|default=30s
|default=no
|desc=ARP timeout on all interfaces that use ARP. Can use postfix ms, s, m, h, d for milliseconds, seconds, minutes, hours or days. if no postfix is set then seconds (s) is used.
|desc=Send out syncookies when the syn backlog queue of a socket overflows. This is to prevent against the common 'SYN flood attack'.
syncookies seriously violate TCP protocol, do not allow o use TCP extensions, can result in serious degradation of some services (f.e. SMTP relaying), visible not by you, but your clients and relays, contacting you.
}}
{{Mr-arg-table
|arg=max-neighbor-entries
|type=integer [0..2147483647]
|default=
|desc= Maximum number of allowed neighbors in ARP table.
}}
}}
{{Mr-arg-table-end
{{Mr-arg-table-end
|arg=tcp_syncookies
|arg=route-cache
|type=yes {{!}} no
|type=yes {{!}} no
|default=no
|default=yes
|desc=Send out syncookies when the syn backlog queue of a socket overflows. This is to prevent against the common 'SYN flood attack'.
|desc= Disable or enable Linux route cache. Note that by disabling route cache, it will also disable fast path.
}}
==Read-Only Properties==
{{Mr-arg-table-h
|prop=Property
|desc=Description
}}
{{Mr-arg-ro-table
|arg=ipv4-fast-path-active
|type=yes {{!}} no
|desc=Indicates whether fast-path is active
}}
{{Mr-arg-ro-table
|arg=ipv4-fast-path-bytes
|type=integer
|desc=Amount of fast-pathed bytes
}}
{{Mr-arg-ro-table
|arg=ipv4-fast-path-packets
|type=integer
|desc=Amount of fast-pathed packets
}}
{{Mr-arg-ro-table
|arg=ipv4-fasttrack-active
|type=yes {{!}} no
|desc= Indicates whether fasttrack is active
}}
{{Mr-arg-ro-table
|arg=ipv4-fasttrack-bytes
|type=integer
|desc= Amount of fasttracked bytes
}}
syncookies seriously violate TCP protocol, do not allow o use TCP extensions, can result in serious degradation of some services (f.e. SMTP relaying), visible not by you, but your clients and relays, contacting you.
Sets Linux base_reachable_time (base_reachable_time_ms) on all interfaces that use ARP. Initial validity of ARP entry is picked from interval [timeout/2..3*timeout/2] (default from 15s to 45s) after neighbor was found. Can use postfix ms, s, m, h, d for milliseconds, seconds, minutes, hours or days. if no postfix is set then seconds (s) is used. Parameter DOES NOT represent a time when ARP entry is removed from ARP cache, ARP cache entries can be stored in the cache for up to 10minutes if reference in route cache is created.
Limit the maximum rates for sending ICMP packets whose type matches icmp-rate-mask to specific targets. 0 to disable any limiting, otherwise the minimum space between responses in milliseconds.
Enable/disable packet forwarding between interfaces. Resets all configuration parameters to defaults according to RFC1812 for routers.
rp-filter (loose | no | strict; Default: no)
Disables enables source validation.
no - No source validation.
strict - Strict mode as defined in RFC3704 Strict Reverse Path. Each incoming packet is tested against the FIB and if the interface is not the best reverse path the packet check will fail. By default failed packets are discarded.
loose - Loose mode as defined in RFC3704 Loose Reverse Path. Each incoming packet's source address is also tested against the FIB and if the source address is not reachable via any interface the packet check will fail.
Current recommended practice in RFC3704 is to enable strict mode to prevent IP spoofing from DDoS attacks. If using asymmetric routing or other complicated routing or VRRP, then loose mode is recommended.
Warning: strict mode does not work with routing tables
secure-redirects (yes | no; Default: yes)
Accept ICMP redirect messages only for gateways, listed in default gateway list.
send-redirects (yes | no; Default: yes)
Whether to send ICMP redirects. Recommended to be enabled on routers.
tcp-syncookies (yes | no; Default: no)
Send out syncookies when the syn backlog queue of a socket overflows. This is to prevent against the common 'SYN flood attack'.
syncookies seriously violate TCP protocol, do not allow o use TCP extensions, can result in serious degradation of some services (f.e. SMTP relaying), visible not by you, but your clients and relays, contacting you.
