Manual:IP/DHCP Client: Difference between revisions
| Line 76: | Line 76: | ||
|default= | |default= | ||
|desc=Host name of the client sent to a DHCP server. If not specified, client's system identity will be used. | |desc=Host name of the client sent to a DHCP server. If not specified, client's system identity will be used. | ||
}} | |||
{{Mr-arg-table | |||
|arg=ipv4 | |||
|type=yes {{!}} no | |||
|default=yes | |||
|desc=Client will receive IPv4 address from the server if this parameter is set. | |||
}} | |||
{{Mr-arg-table | |||
|arg=ipv6-pd | |||
|type=yes {{!}} no | |||
|default=no | |||
|desc=Client will receive delegated prefix from [[M:IP/DHCP_Server#IPv6 | DHCPv6-PD server]]. | |||
}} | |||
{{Mr-arg-table | |||
|arg=pool-name | |||
|type=string | |||
|default= | |||
|desc=Name of the [[M:IPv6/Pool | IPv6 pool]] in which received IPv6 prefix will be added. Applicable if '''ipv6-pd''' is enabled. | |||
}} | |||
{{Mr-arg-table | |||
|arg=pool-prefix-length | |||
|type=string | |||
|default= | |||
|desc=Prefix length parameter that will be set for [[M:IPv6/Pool | IPv6 pool]] in which received IPv6 prefix is added. Applicable if '''ipv6-pd''' is enabled. Prefix length must be greater than the length of received prefix, otherwise prefix-length will be set to received prefix length + 8 bits. | |||
}} | }} | ||
| Line 98: | Line 126: | ||
|desc=Whether to accept the [[M:System/Time#NTP_client_and_server| NTP]] settings advertised by [[M:IP/DHCP Server | DHCP Server]]. (Will override the settings put in the <code>/system ntp client</code> submenu) | |desc=Whether to accept the [[M:System/Time#NTP_client_and_server| NTP]] settings advertised by [[M:IP/DHCP Server | DHCP Server]]. (Will override the settings put in the <code>/system ntp client</code> submenu) | ||
}} | }} | ||
==Status== | ==Status== | ||
Revision as of 09:42, 28 October 2011
Applies to RouterOS: v3, v4 +
Summary
The MikroTik RouterOS DHCP client may be enabled on any Ethernet-like interface at a time. The client will accept an address, netmask, default gateway, and two dns server addresses. The received IP address will be added to the interface with the respective netmask. The default gateway will be added to the routing table as a dynamic entry. Should the DHCP client be disabled or not renew an address, the dynamic default route will be removed. If there is already a default route installed prior the DHCP client obtains one, the route obtained by the DHCP client would be shown as invalid.
RouterOS DHCP cilent asks for following options:
- option 1 - SUBNET_MASK,
- option 3 - GATEWAY_LIST,
- option 6 - TAG_DNS_LIST,
- option 33 - STATIC_ROUTE,
- option 42 - NTP_LIST,
- option 122 - CLASSLESS_ROUTE,
IPv6
Starting from v5.8 DHCP Client can receive delegated prefixes from DHCPv6 server. Currently received prefix is added to IPv6 pool, which later can be used for example in pppoe server configuration.
Quick setup example
Add a DHCP client on ether1 interface:
/ip dhcp-client add interface=ether1 disabled=no
After interface is added, you can use rint" or "print detail" command to see what parameters DHCP client acquired:
[admin@MikroTik] ip dhcp-client> print detail
Flags: X - disabled, I - invalid
0 interface=ether1 add-default-route=yes use-peer-dns=yes use-peer-ntp=yes
status=bound address=192.168.0.65/24 gateway=192.168.0.1
dhcp-server=192.168.0.1 primary-dns=192.168.0.1 primary-ntp=192.168.0.1
expires-after=9m44s
[admin@MikroTik] ip dhcp-client>
Note: If interface used by DHCP client is part of VRF configuration, then default route and other received routes from DHCP server will be added to VRF routing table.
Properties
Sub-menu: /ip dhcp-client
| Property | Description |
|---|---|
| add-default-route (yes | no; Default: yes) | Whether to install default route in routing table received from dhcp server. |
| client-id (string; Default: ) | Corresponds to the settings suggested by the network administrator or ISP. If not specified, client's MAC address will be sent |
| default-route-distance (integer:0..255; Default: ) | Distance of default route. Applicable if add-default-route is set to yes. |
| host-name (string; Default: ) | Host name of the client sent to a DHCP server. If not specified, client's system identity will be used. |
| ipv4 (yes | no; Default: yes) | Client will receive IPv4 address from the server if this parameter is set. |
| ipv6-pd (yes | no; Default: no) | Client will receive delegated prefix from DHCPv6-PD server. |
| pool-name (string; Default: ) | Name of the IPv6 pool in which received IPv6 prefix will be added. Applicable if ipv6-pd is enabled. |
| pool-prefix-length (string; Default: ) | Prefix length parameter that will be set for IPv6 pool in which received IPv6 prefix is added. Applicable if ipv6-pd is enabled. Prefix length must be greater than the length of received prefix, otherwise prefix-length will be set to received prefix length + 8 bits. |
| interface (string; Default: ) | Interface on which DHCP client will be running. |
| use-peer-dns (yes | no; Default: yes) | Whether to accept the DNS settings advertised by DHCP Server. (Will override the settings put in the /ip dns submenu. |
| use-peer-ntp (yes | no; Default: yes) | Whether to accept the NTP settings advertised by DHCP Server. (Will override the settings put in the /system ntp client submenu) |
Status
Command /ip dhcp-client print detail will show current status of dhcp client and read-only properties listed in table below:
| Property | Description |
|---|---|
| address (IP/Netmask) | IP address and netmask, which is assigned to DHCP Client from the Server |
| dhcp-server (IP) | IP address of the DHCP server. |
| expires-after (time) | Time when the lease expires (specified by the DHCP server). |
| gateway (IP) | IP address of the gateway which is assigned by DHCP server |
| invalid (yes | no) | Shows whether configuration is invalid. |
| netmask (IP) | |
| primary-dns (IP) | IP address of the primary DNS server, assigned by the DHCP server |
| primary-ntp (IP) | IP address of the primary NTP server, assigned by the DHCP server |
| secondary-dns (IP) | IP address of the secondary DNS server, assigned by the DHCP server |
| secondary-ntp (IP) | IP address of the secondary NTP server, assigned by the DHCP server |
| status (bound | error | rebinding... | requesting... | searching... | stopped) | Shows the status of DHCP Client |
Menu specific commands
| Property | Description |
|---|---|
| release (numbers) | Release current binding and restart DHCP client |
| renew (numbers) | Renew current leases. If the renew operation was not successful, client tries to reinitialize lease (i.e. it starts lease request procedure (rebind) as if it had not received an IP address yet) |
[ Top | Back to Content ]