Manual:CRS3xx series switches: Difference between revisions
| Line 421: | Line 421: | ||
/interface bridge set bridge1 vlan-filtering=yes | /interface bridge set bridge1 vlan-filtering=yes | ||
</pre> | </pre> | ||
{{ Warning | By enabling <code>vlan-filtering</code> you will be filtering out traffic destined to the CPU, before enabling VLAN filtering you should make sure that you set up a [[Manual:Interface/Bridge#Management_port| Management port]] }} | |||
=(R/M)STP= | =(R/M)STP= | ||
Revision as of 17:02, 18 May 2018
Applies to RouterOS: v6.41 +
Summary
The Cloud Router Switch series are highly integrated switches with high performance ARM CPU and feature-rich packet processor. The CRS switches can be designed into various Ethernet applications including unmanaged switch, Layer 2 managed switch, carrier switch and wired unified packet processing.
Warning: This article applies to CRS3xx series switches and not to CRS1xx/CRS2xx series switches.
Features
| Features | Description |
|---|---|
| Forwarding |
|
| Mirroring |
|
| VLAN |
|
| Bonding |
|
| Quality of Service (QoS) |
|
| Port isolation |
|
| Access Control List |
|
Models
This table clarifies main differences between Cloud Router Switch models.
| Model | Switch Chip | CPU | Cores | Wireless | SFP+ port | Access Control List | Jumbo Frame (Bytes) |
| CRS326-24G-2S+ | Marvell-98DX3236 | 800MHz | 1 | - | + | + | 10218 |
| CRS328-24P-4S+ | Marvell-98DX3236 | 800MHz | 1 | - | + | + | 10218 |
| CRS328-4C-20S-4S+ | Marvell-98DX3236 | 800MHz | 1 | - | + | + | 10218 |
| CRS317-1G-16S+ | Marvell-98DX8216 | 800MHz | 2 | - | + | + | 10218 |
Abbreviations
- FDB - Forwarding Database
- MDB - Multicast Database
- SVL - Shared VLAN Learning
- IVL - Independent VLAN Learning
- PVID - Port VLAN ID
- ACL - Access Control List
- CVID - Customer VLAN ID
- SVID - Service VLAN ID
Port Switching
Since v6.41 bridges will handle all Layer2 forwarding and the use of switch chip (hw-offload) will automatically turn on if appropriate conditions are met.
The rest of RouterOS Switch features remain untouched in usual menus.
By default all newly created bridge ports have hw=yes option and it allows enabling of hw-offload when possible. If such functionality is not required, it can be disabled by hw=no on bridge port to have completely software operated bridging.
Note: Downgrading to previous RouterOS versions will not restore master-port configuration. The bridge with no hw-offload will appear instead and master-port configuration will have to be redone from the beginning.
Example
Use the command lines below to create a bridge and add ports to it. On CRS3xx using other bridge protocol modes will also enable hardware offloading.
/interface bridge add name=bridge1 igmp-snooping=no protocol-mode=none /interface bridge port add bridge=bridge1 interface=ether2 add bridge=bridge1 interface=ether3 add bridge=bridge1 interface=ether4 add bridge=bridge1 interface=ether5
Make sure that hardware offloading is enabled. If H flag is available next to the desired interface, then hardware offloading is active on that port. If hardware offloading flag is not shown, then make sure you haven't enabled features that disable hardware offloading.
Note: Currently it is possible to create only one bridge with hardware offloading on CRS3xx series devices. Use the hw parameter to select which bridge will use hardware offloading.
[admin@MikroTik] > /interface bridge port print Flags: X - disabled, I - inactive, D - dynamic, H - hw-offload # INTERFACE BRIDGE HW PVID PRIORITY PATH-COST INTERNAL-PATH-COST HORIZON 0 H ether2 bridge1 yes 1 0x80 10 10 none 1 H ether3 bridge1 yes 1 0x80 10 10 none 2 H ether4 bridge1 yes 1 0x80 10 10 none 3 H ether5 bridge1 yes 1 0x80 10 10 none
Note: On CRS3xx series switches bridge STP/RSTP/MSTP, IGMP Snooping and VLAN filtering settings don't affect hardware offloading, since RouterOS v6.42 Bonding interfaces are also hardware offloaded.
Host Table
Sub-menu: /interface bridge host
| Property | Description |
|---|---|
| age (read-only: time) | The time since the last packet was received from the host |
| bridge (read-only: name) | The bridge the entry belongs to |
| external-fdb (read-only: flag) | Whether the host was learned using wireless registration table |
| local (read-only: flag) | Whether the host entry is of the bridge itself (that way all local interfaces are shown) |
| mac-address (read-only: MAC address) | Host's MAC address |
| on-interface (read-only: name) | Which of the bridged interfaces the host is connected to |
Example
- Use this command to get the active host table:
[admin@MikroTik] > /interface bridge host print Flags: L - local, E - external-fdb BRIDGE MAC-ADDRESS ON-INTERFACE AGE bridge1 00:00:00:00:00:01 ether2 3s bridge1 00:01:29:FF:1D:CC ether2 0s L bridge1 00:0C:42:52:2E:CF ether2 0s bridge1 00:0C:42:52:2E:D0 ether2 3s bridge1 00:0C:42:5C:A5:AE ether2 0s
VLAN
Since RouterOS v6.41 bridges provides VLAN aware Layer2 forwarding and VLAN tag modifications within the bridge. This set of features makes bridge operation more like a traditional Ethernet switch and allows to overcome Spanning Tree compatibilty issues compared to configuration when tunnel-like VLAN interfaces are bridged. Bridge VLAN Filtering configuration is highly recommended to comply with STP (802.1D), RSTP (802.1w) standards and is mandatory to enable MSTP (802.1s) support in RouterOS.
VLAN Filtering
The main VLAN setting is vlan-filtering which globally controls vlan-awareness and VLAN tag processing in the bridge. If vlan-filtering=no, bridge ignores VLAN tags, works in a shared-VLAN-learning (SVL) mode and cannot modify VLAN tags of packets. Turning on vlan-filtering enables all bridge VLAN related functionality and independent-VLAN-learning (IVL) mode. Besides joining the ports for Layer2 forwarding, bridge itself is also an interface therefore it has Port VLAN ID (pvid).
Sub-menu: /interface bridge
| Property | Description |
|---|---|
| vlan-filtering (yes | no; Default: no) | Globally enables or disables VLAN functionality for bridge. |
| pvid (1..4094; Default: 1) | Port VLAN ID (pvid) specifies which VLAN the untagged ingress traffic is assigned to. It applies e.g. to frames sent from bridge IP and destined to a bridge port. |
Sub-menu: /interface bridge port
| Property | Description |
|---|---|
| frame-types (admit-all | admit-only-untagged-and-priority-tagged | admit-only-vlan-tagged; Default: admit-all) | Specifies allowed ingress frame types on a bridge port. |
| ingress-filtering (yes | no; Default: no) | Enables or disables filtering which looks for an ingress port match in the Bridge VLAN table. |
| pvid (1..4094; Default: 1) | Port VLAN ID (pvid) specifies which VLAN the untagged ingress traffic is assigned to. |
VLAN Table
Bridge VLAN table represents per-VLAN port mapping with an egress VLAN tag action.
tagged ports send out frames with a learned VLAN ID tag.
untagged ports remove VLAN tag before sending out frames if the learned VLAN ID matches the port pvid.
Sub-menu: /interface bridge vlan
| Property | Description |
|---|---|
| bridge (name) | The bridge interface which the respective VLAN entry is intended for. |
| disabled (yes | no; Default: no) | Enables or disables Bridge VLAN entry. |
| tagged (interfaces; Default: none) | Interface list with a VLAN tag adding action in egress. This setting accepts comma separated values. E.g. tagged=ether1,ether2. |
| untagged (interfaces; Default: none) | Interface list with a VLAN tag removing action in egress. This setting accepts comma separated values. E.g. tagged=ether3,ether4. |
| vlan-ids (1..4094) | The list of VLAN IDs for certain port configuration. This setting accepts VLAN ID range as well as comma separated values. E.g. vlan-ids=100-115,120,122,128-130. |
Setup examples
Port Based VLAN
- The configuration for CRS3xx switches is described in the Bridge VLAN FIltering section.
MAC Based VLAN
Note: The CRS3xx Switch Rule table is used for MAC Based VLAN functionality, it supports up to 128 entries.
- Enable switching on ports by creating a bridge with enabled hw-offloading.
/interface bridge add name=bridge1 vlan-filtering=yes /interface bridge port add bridge=bridge1 interface=ether2 hw=yes add bridge=bridge1 interface=ether7 hw=yes
- Add VLANs in the Bridge VLAN table and specify ports.
/interface bridge vlan add bridge=bridge1 tagged=ether2 untagged=ether7 vlan-ids=200,300,400
- Add Switch rules which assign VLAN id based on MAC address.
/interface ethernet switch rule add switch=switch1 ports=ether7 src-mac-address=A4:12:6D:77:94:43/FF:FF:FF:FF:FF:FF new-vlan-id=200 add switch=switch1 ports=ether7 src-mac-address=84:37:62:DF:04:20/FF:FF:FF:FF:FF:FF new-vlan-id=300 add switch=switch1 ports=ether7 src-mac-address=E7:16:34:A1:CD:18/FF:FF:FF:FF:FF:FF new-vlan-id=400
Protocol Based VLAN
Note: The CRS3xx Switch Rule table is used for Protocol Based VLAN functionality, it supports up to 128 entries.
- Enable switching on ports by creating a bridge with enabled hw-offloading.
/interface bridge add name=bridge1 vlan-filtering=yes /interface bridge port add bridge=bridge1 interface=ether2 hw=yes add bridge=bridge1 interface=ether6 hw=yes add bridge=bridge1 interface=ether7 hw=yes add bridge=bridge1 interface=ether8 hw=yes
- Add VLANs in the Bridge VLAN table and specify ports.
/interface bridge vlan add bridge=bridge1 tagged=ether2 untagged=ether6 vlan-ids=200 add bridge=bridge1 tagged=ether2 untagged=ether7 vlan-ids=300 add bridge=bridge1 tagged=ether2 untagged=ether8 vlan-ids=400
- Add Switch rules which assign VLAN id based on MAC protocol.
/interface ethernet switch rule add mac-protocol=ip new-vlan-id=200 ports=ether6 switch=switch1 add mac-protocol=ipx new-vlan-id=300 ports=ether7 switch=switch1 add mac-protocol=0x80F3 new-vlan-id=400 ports=ether8 switch=switch1
VLAN Tunneling (Q-in-Q)
Since RouterOS v6.43rc14 it is possible to use a provider bridge (IEEE 802.1ad) VLAN filtering and hardware offloading at the same time on CRS3xx series switches. The configuration for CRS3xx switches is described in the Bridge VLAN Tunneling (Q-in-Q) section.
Ingress VLAN translation
It is possible to translate a certain VLAN ID to a different VLAN ID using ACL rules on an ingress port. This can be done by doing the following:
- Create a new bridge and add ports to it with hardware offloading:
/interface bridge add name=bridge1 vlan-filtering=no /interface bridge port add interface=ether1 bridge=bridge1 hw=yes add interface=ether2 bridge=bridge1 hw=yes
- Add an ACL rule to translate a VLAN ID:
/interface ethernet switch rule add new-vlan-id=20 ports=ether1 switch=switch1 vlan-id=10
- Add the NEW VLAN ID to the bridge VLAN table:
/interface bridge vlan add bridge=bridge tagged=ether1,ether2 vlan-ids=20
- Enable bridge VLAN filtering:
/interface bridge set bridge1 vlan-filtering=yes
Warning: By enabling vlan-filtering you will be filtering out traffic destined to the CPU, before enabling VLAN filtering you should make sure that you set up a Management port
(R/M)STP
Network loops may emerge (intentionally or not) in complex topologies. Without any special treatment, loops would prevent network from functioning normally, as they would lead to avalanche-like packet multiplication. Each bridge runs an algorithm which calculates how the loop can be prevented. STP and RSTP allows bridges to communicate with each other, so they can negotiate a loop free topology. All other alternative connections that would otherwise form loops, are put to standby, so that should the main connection fail, another connection could take its place. This algorithm exchanges configuration messages (BPDU - Bridge Protocol Data Unit) periodically, so that all bridges are updated with the newest information about changes in network topology. (R/M)STP selects a root bridge which is responsible for network reconfiguration, such as blocking and opening ports on other bridges. The root bridge is the bridge with the lowest bridge ID.
As of RouterOS v6.41 all CRS3xx series switches support (R/M)STP bridge protocol mode and hardware offloading simultaneously, meaning that it possible to use the switch chip's built-in VLAN filtering function in conjunction with bridge's Spanning Tree Protocol features and forward packets at wire-speed. There are a lot of considerations that should be made when designing a STP enabled network, more detailed case studies can be found in the Spanning Tree Protocol section.
Sub-menu: /interface bridge
| Property | Description |
|---|---|
| protocol-mode (mstp | none | rstp | stp; Default: rstp) |
|
Bonding
Since RouterOS v6.42 all CRS3xx series switches support hardware offloading with bonding interfaces. Only 802.3ad and balance-xor bonding modes are hardware offloaded, other bonding modes will use the CPU's resources. You can find more information about the bonding interfaces in the Bonding Interface section. If 802.3ad mode is used, then LACP (Link Aggregation Control Protocol) is supported.
To create a hardware offloaded bonding interface, you must create a bonding interface with a supported bonding mode:
/interface bonding add mode=802.3ad name=bond1 slaves=ether1,ether2
This interface can be added to a bridge alongside with other interfaces:
/interface bridge add name=bridge /interface bridge port add bridge=bridge interface=bond1 hw=yes add bridge=bridge interface=ether3 hw=yes add bridge=bridge interface=ether4 hw=yes
Note: Don't add interfaces to a bridge that are already in a bond, RouterOS will not allow you to add an interface that is already a slave to a bridge as there is no need to do it since a bonding interface already contains the slave interfaces.
Make sure that the bonding interface is hardware offloaded by checking the "H" flag:
/interface bridge port print Flags: X - disabled, I - inactive, D - dynamic, H - hw-offload # INTERFACE BRIDGE HW 0 H bond1 bridge yes 1 H ether3 bridge yes 2 H ether4 bridge yes
Note: The built-in switch chip will always use Layer2+Layer3+Layer4 for transmit hash policy, changing the transmit hash policy manually will have no effect.
Port isolation
Since RouterOS v6.43rc11 is it possible to create a Private VLAN setup on CRS3xx series switches, example can be found in the Switch chip port isolation manual page.
IGMP Snooping
IGMP Snooping which controls multicast streams and prevents multicast flooding is implemented in RouterOS starting from version 6.41. It's settings are placed in bridge menu and it works independently in every bridge interface. Software driven implementation works on all devices with RouterOS but CRS1xx/2xx/3xx series switches also support IGMP Snooping with hardware offloading.
- Use this command to enable IGMP Snooping on a bridge interface:
/interface bridge set bridge1 igmp-snooping=yes
- Use this command to get current Multicast Database entries:
[admin@MikroTik] > /interface bridge mdb print
BRIDGE VID GROUP PORTS
bridge1 200 229.1.1.2 ether3
ether2
ether1
bridge1 300 231.1.3.3 ether4
ether3
ether2
bridge1 400 229.10.10.4 ether4
ether3
bridge1 500 234.5.1.5 ether5
ether1
Mirroring
Mirroring lets the switch 'sniff' all traffic that is going in a switch chip and send a copy of those packets out to another port (mirror-target). This feature can be used to easily set up a 'tap' device that allows you to inspect the traffic on your network on a traffic analyzer device. It is possible to set up a simple port based mirroring where, but it is also possible to setup more complex mirroring based on various parameters. Note that mirror-target port has to belong to same switch. (See which port belong to which switch in /interface ethernet menu). Also mirror-target can have a special 'cpu' value, which means that 'sniffed' packets will be sent out of switch chips cpu port. There are many possibilities that can be used to mirror certain traffic, below you can find most common mirroring examples:
- Port Based Mirroring
/interface ethernet switch set switch1 mirror-source=ether2 mirror-target=ether3
- VLAN Based Mirroring
/interface bridge set bridge1 vlan-filtering=yes /interface ethernet switch set switch1 mirror-target=ether3 mirror-source=none /interface ethernet switch rule add mirror=yes ports=ether1 switch=switch1 vlan-id=11
Warning: By enabling vlan-filtering you will be filtering out traffic destined to the CPU, before enabling VLAN filtering you should make sure that you set up a Management port
- MAC Based Mirroring
/interface ethernet switch set switch1 mirror-target=ether3 mirror-source=none /interface ethernet switch rule add mirror=yes ports=ether1 switch=switch1 dst-mac-address=64:D1:54:D9:27:E6/FF:FF:FF:FF:FF:FF add mirror=yes ports=ether1 switch=switch1 src-mac-address=64:D1:54:D9:27:E6/FF:FF:FF:FF:FF:FF
- Protocol Based Mirroring
/interface ethernet switch set switch1 mirror-target=ether3 mirror-source=none /interface ethernet switch rule add mirror=yes ports=ether1 switch=switch1 mac-protocol=ipx
- IP Based Mirroring
/interface ethernet switch set switch1 mirror-target=ether3 mirror-source=none /interface ethernet switch rule add mirror=yes ports=ether1 switch=switch1 src-address=192.168.88.0/24 add mirror=yes ports=ether1 switch=switch1 dst-address=192.168.88.0/24
There are other options as well, check the ACL section to find out all possible parameters that can be used to match packets.
Quality of Service
It is possible to limit ingress and egress bandwidth per port using the /interface ethernet switch port menu.
Sub-menu: /interface ethernet switch port
| Property | Description |
|---|---|
| egress-rate (bps; Default: unlimited) | Specifies port egress rate in bps, limited by using traffic shaper. |
| ingress-rate (bps; Default: unlimited) | Specifies port ingress rate in bps, limited by using traffic policer. |
- For example, to limit ingress and egress traffic on ether1 use these commands:
/interface ethernet switch port set ether1 ingress-rate=10M egress-rate=5M
Traffic Storm Control
Since RouterOS v6.42 it is possible to enable traffic storm control on CRS3xx series devices. It is possible to limit broadcast, unknown multicast and unknown unicast traffic. These settings should be applied to ingress ports, the egress traffic will be limited.
Note: The storm control parameter is specified in percentage (%) of the link speed. If your link speed is 1Gbps, then specifying storm-rate as 10 will allow only 100Mbps of broadcast, unknown multicast and/or unknown unicast traffic to be forwarded.
Sub-menu: /interface ethernet switch port
| Property | Description |
|---|---|
| limit-broadcasts (yes | no; Default: yes) | Limit broadcast traffic on switch port. |
| limit-unknown-multicasts (yes | no; Default: no) | Limit unknown multicast traffic on switch port. |
| limit-unknown-unicasts (yes | no; Default: no) | Limit unknown unicast traffic on switch port. |
| storm-rate (integer 0..100; Default: 100) | Amount of broadcast, unknown multicast and/or unknown unicast traffic is limited to in percentage of the link speed. |
Warning: Devices with Marvell-98DX3236 switch chip cannot distinguish unknown multicast traffic from all multicast traffic. For example, CRS326-24G-2S+ will limit all multicast traffic when limit-unknown-multicasts and storm-rate is used. For other devices, for example, CRS317-1G-16S+ the limit-unknown-multicasts parameter will limit only unknown multicast traffic (addresses that are not present in /interface bridge mdb
- For example, to limit 1% (10Mbps) of broadcast and unknown unicast traffic on ether1 (1Gbps), use the following commands:
/interface ethernet switch port set ether1 storm-rate=1 limit-broadcasts=yes limit-unknown-unicasts=yes
Switch Rules (ACL)
Access Control List contains of ingress policy and egress policy engines and allows to configure up to 128 policy rules (limited by RouterOS). It is advanced tool for wire-speed packet filtering, forwarding and modifying based on Layer2, Layer3 and Layer4 protocol header field conditions.
Sub-menu: /interface ethernet switch rule
| Property | Description |
|---|---|
| copy-to-cpu (no | yes; Default: no) | Clones the matching packet and sends it to the CPU. |
| disabled (yes | no; Default: no) | Enables or disables ACL entry. |
| dscp (0..63) | Matching DSCP field of the packet. |
| dst-address (IP address/Mask) | Matching destination IP address and mask. |
| dst-address6 (IPv6 address/Mask) | Matching destination IPv6 address and mask. |
| dst-mac-address (MAC address/Mask) | Matching destination MAC address and mask. |
| dst-port (0..65535) | Matching destination protocol port number. |
| flow-label (0..1048575) | Matching IPv6 flow label. |
| mac-protocol (802.2 | arp | homeplug-av | ip | ipv6 | ipx | lldp | loop-protect | mpls-multicast | mpls-unicast | packing-compr | packing-simple | pppoe | pppoe-discovery | rarp | service-vlan | vlan | or 0..65535 | or 0x0000-0xffff) | Matching particular MAC protocol specified by protocol name or number |
| mirror (no | yes) | Clones the matching packet and sends it to the mirror-target port. |
| new-dst-ports (ports) | Changes the destination port as specified. An empty setting will drop the packet. A specified port will redirect the packet to it. When the parameter is not used, the packet will be accepted. Multiple "new-dst-ports" are not supported on CRS3xx series switches. |
| new-vlan-id (0..4095) | Changes the VLAN ID to the specified value. Requires vlan-filtering=yes. |
| new-vlan-priority (0..7) | Changes the VLAN priority tag. Requires vlan-filtering=yes. |
| ports (ports) | Matching ports on which will the rule apply on received traffic. |
| protocol (dccp | ddp | egp | encap | etherip | ggp | gre | hmp | icmp | icmpv6 | idpr-cmtp | igmp | ipencap | ipip | ipsec-ah | ipsec-esp | ipv6 | ipv6-frag | ipv6-nonxt | ipv6-opts | ipv6-route | iso-tp4 | l2tp | ospf | pim | pup | rdp | rspf | rsvp | sctp | st | tcp | udp | udp-lite | vmtp | vrrp | xns-idp | xtp | or 0..255) | Matching particular IP protocol specified by protocol name or number. |
| redirect-to-cpu (no | yes) | Changes the destination port of a matching packet to the CPU. |
| src-address (IP address/Mask) | Matching source IP address and mask. |
| src-address6 (IPv6 address/Mask) | Matching source IPv6 address and mask. |
| src-mac-address (MAC address/Mask) | Matching source MAC address and mask. |
| src-port (0..65535) | Matching source protocol port number. |
| switch (switch group) | Matching switch group on which will the rule apply. |
| traffic-class (0..255) | Matching IPv6 traffic class. |
| vlan-id (0..4095) | Matching VLAN ID. Requires vlan-filtering=yes. |
| vlan-header (not-present | present) | Matching VLAN header, whether the VLAN header is present or not. |
| vlan-priority (0..7) | Matching VLAN priority. |
Action parameters:
- copy-to-cpu
- redirect-to-cpu
- mirror
- new-dst-ports (can be used to drop packets)
- new-vlan-id
- new-vlan-priority
- rate
Conditional parameters:
- Layer2 conditions:
- dst-mac-address
- mac-protocol
- src-mac-address
- vlan-id
- vlan-header
- vlan-priority
- Layer3 conditions:
- dscp
- protocol
- IPv4 conditions:
- dst-address
- src-address
- IPv6 conditions:
- dst-address6
- flow-label
- src-address6
- traffic-class
- Layer4 conditions:
- dst-port
- src-port
Note: For VLAN related matchers or VLAN related action parameters to work, you need to enable vlan-filtering on the bridge interface and make sure that hardware offloading is enabled on those ports, otherwise these parameters will not have any effect.
Warning: When vlan-protocol is set to 802.1Q, then VLAN related ACL rules are relevant to 0x8100 (CVID) packets, this includes vlan-id and new-vlan-id. When vlan-protocol is set to 802.1ad, then ACL rules are relevant to 0x88A8 (SVID) packets. For example, with 802.1Q the vlan-id matcher will match CVID packets, but with 802.1ad the vlan-id matcher will match SVID packets.
Dual Boot
“Dual boot” feature allows you to choose which operating system you prefer to use, RouterOS or SwOS. Device operating system could be changed using:
- Serial Terminal (/system routerboard settings set boot-os=swos)
- Winbox
- Webfig
- Serial Console
 |
 |
 |
More details about SwOS are described here: SwOS manual
See also
[ Top | Back to Content ]