Manual:Interface/Ethernet: Difference between revisions
Jump to navigation
Jump to search
mNo edit summary |
m styling |
||
| Line 1: | Line 1: | ||
{{Versions|v3, v4}} | {{Versions|v3, v4+}} | ||
<div class=manual> | <div class=manual> | ||
==Summary== | |||
<p><b>Sub-menu:</b> <code>/interface ethernet</code></ | <p id="shbox"><b>Sub-menu:</b> <code>/interface ethernet</code> | ||
<br /> | |||
<b>Standards:</b> <code>[http://grouper.ieee.org/groups/802/3/ IEEE 802.3]</code></p> | |||
<br /> | <br /> | ||
<p> | <p> | ||
| Line 11: | Line 12: | ||
</p> | </p> | ||
==Properties== | |||
<br /> | <br /> | ||
| Line 235: | Line 236: | ||
</table> | </table> | ||
==Menu specific commands== | |||
<table class="styled_table"> | <table class="styled_table"> | ||
<tr> | <tr> | ||
| Line 259: | Line 260: | ||
</table> | </table> | ||
==Monitor== | |||
<code>/interface ethernet monitor</code> command prints out current link, rate and duplex status of an interface. | <code>/interface ethernet monitor</code> command prints out current link, rate and duplex status of an interface. | ||
| Line 320: | Line 321: | ||
</pre> | </pre> | ||
==Stats== | |||
RouterOS v3.22 introduces a new command: | RouterOS v3.22 introduces a new command: | ||
<pre> | |||
/interface ethernet print stats | |||
</pre> | |||
This command will display all kinds of other statistics if the interface is supporting them (currently only RB450G ether2-ether5 and also RB750 ether2-ether5). Complete list of properties can be found in [[#Read-only_properties | section above]]<br /> | This command will display all kinds of other statistics if the interface is supporting them (currently only RB450G ether2-ether5 and also RB750 ether2-ether5). Complete list of properties can be found in [[#Read-only_properties | section above]]<br /> | ||
<br /> | <br /> | ||
| Line 371: | Line 372: | ||
</pre> | </pre> | ||
==Switch== | |||
<p><b>Sub-menu:</b> <code>/interface ethernet switch</code></p> | <p id="shbox"><b>Sub-menu:</b> <code>/interface ethernet switch</code></p> | ||
This submenu allows to configure certain RouterBoard switch chip feature. [[Switch_Chip_Features | Read more >>]]. | This submenu allows to configure certain RouterBoard switch chip feature. [[Switch_Chip_Features | Read more >>]]. | ||
| Line 378: | Line 379: | ||
</div> | </div> | ||
{{cont}} | |||
[[Category:Manual|E]] | [[Category:Manual|E]] | ||
Revision as of 11:06, 30 April 2010
Applies to RouterOS: v3, v4+
Summary
Sub-menu: /interface ethernet
Standards: IEEE 802.3
MikroTik RouterOS supports various types of Ethernet interfaces.
Properties
| Property | Description |
|---|---|
| arp (disabled | enabled | proxy-arp | reply-only; Default: enabled) | Address Resolution Protocol mode |
| auto-negotiation (yes | no; Default: yes) | When enabled, the interface "advertises" its maximum capabilities to achieve the best connection possible. Note: Auto-negotiation must be disabled on both ends, otherwise Ethernets may not work properly. Note2: Gigabit link cannot work with auto-negotiation disabled. |
| bandwidth (integer/integer; Default: unlimited/unlimited) | Sets max rx/tx bandwidth that will be handled by an interface. |
| cable-setting (default | short | standard; Default: default) | changes the cable length setting (only applicable to NS DP83815/6 cards) |
| disable-running-check (yes | no; Default: yes) | Disable running check. If this value is set to 'no', the router automatically detects whether the NIC is connected with a device in the network or not. |
| full-duplex (yes | no; Default: yes) | Defines whether the transmission of data appears in two directions simultaneously |
| l2mtu (integer; Default: ) | Layer2 Maximum transmission unit. Read more>> |
| mac-address (MAC; Default: ) | Media Access Control number of an interface. |
| master-port (name | none; Default: none) | Sets switch group master interface |
| mdix-enable (yes | no; Default: ) | Whether the MDI/X auto crosscable correction feature is enabled for the port |
| mtu (integer; Default: 1500) | Layer3 Maximum transmission unit |
| name (string; Default: ) | Name of an interface |
| speed (10Mbps | 100Mbps | 1Gbps; Default: max available) | Sets the data transmission speed of the interface. By default, this value is the maximal data rate supported by the interface |
Read-only properties
| Property | Description |
|---|---|
| running (yes | no) | Whether interface is running. Note that some interface does not have running check and they are always reported as "running" |
| rx-1024-1518 (integer) | Total count of received 1024 to 1518 byte packets |
| rx-128-255 (integer) | Total count of received 128 to 255 byte packets |
| rx-1519-max (integer) | Total count of received packets larger than 1519 bytes |
| rx-256-511 (integer) | Total count of received 256 to 511 byte packets |
| rx-512-1023 (integer) | Total count of received 512 to 1023 byte packets |
| rx-64 (integer) | Total count of received 64 byte packets |
| rx-65-127 (integer) | Total count of received 65 to 127 byte packets |
| rx-align-error (integer) | Total count of received align error messages |
| rx-broadcast (integer) | Total count of received broadcast packets |
| rx-bytes (integer) | Total count of received bytes |
| rx-fcs-error (integer) | Total count of received frames with incorrect checksum |
| rx-fragment (integer) | Total count of received fragmented frames |
| rx-multicast (integer) | Total count of received multicast packets |
| rx-overflow (integer) | |
| rx-pause (integer) | Amount of received pause frames |
| rx-runt (integer) | Amount of received frames shorter than the minimum 64 bytes but with a valid CRC |
| rx-too-long (integer) | |
| slave (yes | no) | Whether interface is configured as a slave of another interface (for example Bonding) |
| switch (integer) | ID to which switch chip interface belongs to. |
| tx-1024-1518 (integer) | |
| tx-128-255 (integer) | |
| tx-1519-max (integer) | |
| tx-256-511 (integer) | |
| tx-512-1023 (integer) | |
| tx-64 (integer) | |
| tx-65-127 (integer) | |
| tx-align-error (integer) | |
| tx-broadcast (integer) | |
| tx-bytes (integer) | |
| tx-fcs-error (integer) | |
| tx-fragment (integer) | |
| tx-multicast (integer) | |
| tx-overflow (integer) | |
| tx-pause (integer) | |
| tx-runt (integer) | |
| tx-too-long (integer) |
Menu specific commands
| Property | Description |
|---|---|
| blink ([id, name]) | Blink Ethernet leds |
| monitor ([id, name]) | Monitor ethernet status. Read more>> |
| reset-counters ([id, name]) | Reset stats counters. Read more>> |
| reset-mac ([id, name]) | Reset MAC address to manufacturers default. |
Monitor
/interface ethernet monitor command prints out current link, rate and duplex status of an interface.
Properties:
| Property | Description |
|---|---|
| auto-negotiation (done | incomplete) | Current auto negotiation status.
|
| default-cable-settings (short | standard) | default cable length setting (only applicable to NS DP83815/6 cards)
|
| full-duplex (yes | no) | Whether transmission of data occurs in two directions simultaneously |
| rate (10Mbps | 100Mbps | 1Gbps) | Actual data rate of the connection |
| status (link-ok | no-link | unknown) | Current link status of an interface
|
Example output of ethernet status:
[admin@MikroTik] /interface ethernet> monitor ether1
status: link-ok
auto-negotiation: done
rate: 1Gbps
full-duplex: yes
Stats
RouterOS v3.22 introduces a new command:
/interface ethernet print stats
This command will display all kinds of other statistics if the interface is supporting them (currently only RB450G ether2-ether5 and also RB750 ether2-ether5). Complete list of properties can be found in section above
For example, output of ethernet stats on RB450G:
[admin@MikroTik] /interface ethernet> print stats
name: ether1-gateway ether2-local ether3-local ether4-local ether5-local
rx-broadcast: 22 31 3666 11
rx-pause: 0 0 0 0
rx-multicast: 4 7 1423 5
rx-fcs-error: 0 0 2 0
rx-align-error: 0 0 0 0
rx-runt: 0 0 0 0
rx-fragment: 0 0 1 0
rx-64: 0 0 0 0
rx-65-127: 8 14 21598 10
rx-128-255: 0 0 0 0
rx-256-511: 18 24 2245 6
rx-512-1023: 28926 7649 371938 24476
rx-1024-1518: 0 0 0 0
rx-1519-max: 0 0 0 0
rx-too-long: 0 0 0 0
rx-overflow: 0 0 0 0
rx-bytes: 15337844 4063737 199738064 12975401
tx-broadcast: 13 13 1496 8
tx-pause: 0 0 0 0
tx-multicast: 13 13 1496 8
tx-underrun: 0 0 0 0
tx-64: 0 0 0 0
tx-65-127: 26 26 2992 16
tx-128-255: 0 0 0 0
tx-256-511: 0 0 0 0
tx-512-1023: 0 0 0 0
tx-1024-1518: 0 0 0 0
tx-1519-max: 0 0 0 0
tx-too-long: 0 0 0 0
tx-collision: 0 0 0 0
tx-excessive-collision: 0 0 0 0
tx-multiple-collision: 0 0 0 0
tx-single-collision: 0 0 0 0
tx-excessive-deferred: 0 0 0 0
tx-deferred: 0 0 0 0
tx-late-collision: 0 0 0 0
tx-bytes: 2561 2561 294712 1576
Switch
Sub-menu: /interface ethernet switch
This submenu allows to configure certain RouterBoard switch chip feature. Read more >>.
[ Top | Back to Content ]