Manual:Default Configurations

Applies to RouterOS: v5

List of Default Configs

Integrated Indoors

	Wan port	Lan port	Wireless mode	ht chain	ht extension	dhcp-server	dhcp-client	Firewall	NAT	Default IP	Mac Server
RB750 RB750G	ether1	Switched ether2-ether5	-	-	-	on lan port	on wan port	blocked access to wan port	Masquerade wan port	192.168.88.1/24 on lan port	Disabled on wan port
RB751-2n	ether1	Switched ether2-ether5, bridged wlan1 with switch	AP b/g/n 2412MHz	0	above-control	on lan port	on wan port	blocked access to wan port	Masquerade wan port	192.168.88.1/24 on lan port	Disabled on wan port
RB1100	-	-	-	-	-	-	-	-	-	192.168.88.1/24 on ether1	-
RB1200	-	-	-	-	-	-	-	-	-	192.168.88.1/24 on ether1	-
RB2011	-	-	-	-	-	-	-	-	-	192.168.88.1/24 on ether1	-

Integrated Outdoors

	Wan port	Lan port	Wireless mode	ht chain	ht extension	dhcp-server	dhcp-client	Firewall	NAT	Default IP	Mac Server
Groove 5Hn	wlan1	ether1	station a/n 5300MHz	0	above control	on lan port	on wan port	blocked access to wan port	Masquerade wan port	192.168.88.1/24 on lan port	Disabled on wan port
Groove A-5Hn	-	bridged wlan1,ether1	AP a/n 5300MHz	0	-	-	-	-	-	192.168.88.1/24 on lan port	-
SXT 5D	wlan1	ether1	station a/n 5300MHz	0,1	above control	on lan port	on wan port	blocked access to wan port	Masquerade wan port	192.168.88.1/24 on lan port	Disabled on wan port
OmniTik	ether1	Switched ether2-ether5, bridged wlan1 with switch	AP a/n 5300MHz	0,1	-	on lan port	on wan port	blocked access to wan port	Masquerade wan port	192.168.88.1/24 on lan port	Disabled on wan port

Engineered

	Wan port	Lan port	Wireless mode	ht chain	ht extension	dhcp-server	dhcp-client	Firewall	NAT	Default IP	Mac Server
RB450 RB450G	ether1	Switched ether2-ether5	-	-	-	on lan port	on wan port	blocked access to wan port	Masquerade wan port	192.168.88.1/24 on lan port	Disabled on wan port
RB711-5	wlan1	ether1	station a/n 5300MHz	0	above control	on lan port	on wan port	blocked access to wan port	Masquerade wan port	192.168.88.1/24 on lan port	Disabled on wan port
RB711A-5Hn	-	bridged wlan1,ether1	AP a/n 5300MHz	0	-	-	-	-	-	192.168.88.1/24 on lan port	-
RB711-2	wlan1	ether1	station b/g/n 2412MHz	0	above control	on lan port	on wan port	blocked access to wan port	Masquerade wan port	192.168.88.1/24 on lan port	Disabled on wan port

Wan Port

When applying configuration WAN port is renamed to "<wan port>-gateway", for example, if wan port is ether1, it will be renamed to "ether1-gateway".

Local Port

Local port can be:

• single interface
• ethernets configured in switch group
• bridged all interfaces that are not WAN and switch slaves.

If ports are switched then master port is renamed to "<ethernet name>-master-local" and slaves to "<ethernet name>-slave-local".

Lets take RB751 as an example. Board has ether1 configured as WAN port, it has switch chip and one pre-configured wireless interface. So in this case all ethernets except ether1 are grouped in switch group and bridged with wireless interface.

Generated config will be:

/interface set ether2 name=ether2-master-local;
/interface set ether3 name=ether3-slave-local;
/interface set ether4 name=ether4-slave-local;
/interface set ether5 name=ether5-slave-local;
/interface ethernet set ether3-slave-local master-port=ether2-master-local;
/interface ethernet set ether4-slave-local master-port=ether2-master-local;
/interface ethernet set ether5-slave-local master-port=ether2-master-local;

/interface bridge add name=bridge-local disabled=no auto-mac=no protocol-mode=rstp;

:local bMACIsSet 0;
:foreach k in=[/interface find] do={
        :local tmpPort [/interface get $k name];
        :if ($bMACIsSet = 0) do={
               :if ([/interface get $k type] = "ether") do={
                      /interface bridge set "bridge-local" admin-mac=[/interface ethernet get $tmpPort mac-address];
                      :set bMACIsSet 1;
                 }
        }
        :if (!($tmpPort~"bridge" || $tmpPort~"ether1" || $tmpPort~"slave")) do={
               /interface bridge port add bridge=bridge-local interface=$tmpPort;
        }
}

Wireless Config

Wireless configuration depends on market segment for which board is designed. It can be configured as AP or station in 2GHz and 5GHz frequencies. Default 2GHz frequency is 2412 and default 5GHz frequency is 5300. SSID is "Mikrotik".

If board has two chains (letter D in the naming of the board), then both chains are enabled. HT Extension is enabled on all CPEs.

For example generated config on RB751:

:if ( $wirelessEnabled = 1) do={
# wait for wireless
       :while ([/interface wireless find] = "") do={ :delay 1s; };

       /interface wireless set wlan1 mode=ap-bridge band=2ghz-b/g/n ht-txchains=0,1 ht-rxchains=0,1 \
               disabled=no country=no_country_set wireless-protocol=any
       /interface wireless set wlan1 channel-width=20/40mhz-ht-above ;
}

Default IP and DHCP Config

Default IP address on all boards is 192.168.88.1/24. Boards without specific configuration has IP address set on ether1, other boards has IP address on LAN interface.

All boards that has WAN port configured, DHCP client is set on WAN port.

Typically on all CPEs DHCP server is set on LAN port, giving out addresses in range from 192.168.88.2-192.168.88.254

As an example RB751 applied DHCP config.

/ip dhcp-client add interface=ether1-gateway disabled=no

/ip pool add name="default-dhcp" ranges=192.168.88.10-192.168.88.254;
/ip dhcp-server 
  add name=default address-pool="default-dhcp" interface=bridge-local disabled=no;

/ip dhcp-server network 
  add address=192.168.88.0/24 gateway=192.168.88.1 dns-server=192.168.88.1 comment="default configuration";

Firewall, NAT and MAC server

All boards with configured WAN port has configured protection on that port. Any traffic leaving WAN port is masqueraded.

Config example:

/ip firewall {
      filter add chain=input action=accept protocol=icmp comment="default configuration"
      filter add chain=input action=accept connection-state=established in-interface=ether1-gateway comment="default configuration"
      filter add chain=input action=accept connection-state=related in-interface=ether1-gateway comment="default configuration"
      filter add chain=input action=drop in-interface=ether1-gateway comment="default configuration"
      nat add chain=srcnat out-interface=ether1-gateway action=masquerade comment="default configuration"
}


/tool mac-server remove [find];
/tool mac-server mac-winbox disable [find];
:foreach k in=[/interface find] do={
       :local tmpName [/interface get $k name];
       :if (!($tmpName~"ether1")) do={
              /tool mac-server add interface=$tmpName disabled=no;
              /tool mac-server mac-winbox add interface=$tmpName disabled=no;
        }
}
/ip neighbor discovery set [find name="ether1-gateway"] discover=no

DNS

Every board allows remote DNS requests and static DNS name is pre-configured.

	/ip dns {
		set allow-remote-requests=yes
		static add name=router address=192.168.88.1
	}

[ Top | Back to Content ]