Manual:SNMP

Simple Network Management Protocol (SNMP) is an "Internet-standard protocol for managing devices on IP networks. SNMP can be used to graph various data with tools such as CACTI, MRTG or The Dude

Specifications

RouterOS supports SNMP v1,2 and 3. SNMP write is also supported.

Applies to RouterOS: v5

Configuration

To enable SNMP in RouterOS:

[admin@MikroTik] /snmp> print 
       enabled: no
       contact: 
       location: 
       engine-id: 
       trap-community: (unknown)
       trap-version: 1
[admin@MikroTik] /snmp>  set enabled yes

You can also specify administrative contact information in the above settings.

Management information base (MIB)

You can download the latest MikroTik RouterOS MIB file. RouterOS v5.x uses such MIBs:

• MIKROTIK-MIB
• MIB-2
• HOST-RESOURCES-MIB
• IF-MIB
• IP-MIB
• IP-FORWARD-MIB
• IPV6-MIB
• BRIDGE-MIB
• DHCP-SERVER-MIB
• CISCO-AAA-SESSION-MIB
• ENTITY-MIB
• UPS-MIB
• SQUID-MIB

Object identifiers (OID)=

Each OID identifies a variable that can be read via SNMP. Although the MIB file contains all the needed OID values, you can also print individual OID information in the console with the print oid command at any menu level:

[admin@MikroTik] /interface> print oid

Flags: D - dynamic, X - disabled, R - running, S - slave 
 0  R  name=.1.3.6.1.2.1.2.2.1.2.1 mtu=.1.3.6.1.2.1.2.2.1.4.1 
       mac-address=.1.3.6.1.2.1.2.2.1.6.1 admin-status=.1.3.6.1.2.1.2.2.1.7.1 
       oper-status=.1.3.6.1.2.1.2.2.1.8.1 bytes-in=.1.3.6.1.2.1.2.2.1.10.1 
       packets-in=.1.3.6.1.2.1.2.2.1.11.1 discards-in=.1.3.6.1.2.1.2.2.1.13.1 
       errors-in=.1.3.6.1.2.1.2.2.1.14.1 bytes-out=.1.3.6.1.2.1.2.2.1.16.1 
       packets-out=.1.3.6.1.2.1.2.2.1.17.1 discards-out=.1.3.6.1.2.1.2.2.1.19.1 
       errors-out=.1.3.6.1.2.1.2.2.1.20.1 

SNMP write

Since RouterOS v3, SNMP write is supported for some functions. SNMP write allows to change router configuration with SNMP requests. Consider to secure access to router or to router's SNMP, when SNMP and write-access are enabled.

Writable options

To change settings by SNMP requests, use the command below to allow SNMP write for the selected community, Write-access option for SNMP is available from v3.14,

/snmp community set <number> write-access=yes

System Identity

It's possible to change router system identity by SNMP set command,

snmpset -c public -v 1 192.168.0.0 1.3.6.1.2.1.1.5.0  s New_Identity

• snmpset, SNMP application used for SNMP SET requests to set information on a network entity;
• public, router's community name;
• 192.168.0.0, IP address of the router;
• 1.3.6.1.2.1.1.5.0, SNMP value for router's identity;

SNMPset command above is equal to the RouterOS command,

/system identity set identity=New_Identity

Reboot

It's possible to reboot the router with SNMP set commamd, you need to set value for reboot SNMP settings, which is not equal to 0,

snmpset -c public -v 1 192.168.0.0 1.3.6.1.4.1.14988.1.1.7.1.0 s 1

• 1.3.6.1.4.1.14988.1.1.7.1.0, SNMP value for the router reboot;
• s 1, snmpset command to set value, value should not be equal to 0;

Reboot snmpset command is equal to the RouterOS command,

/system reboot

Run Script

SNMP write allows to run scripts on the router from system script menu, when you need to set value for SNMP setting of the script,

 
snmpset -c public -v 1 192.168.0.0 1.3.6.1.4.1.14988.1.1.8.1.1.3.X s 1

• X, script number, numeration starts from 1;
• s 1, snmpset command to set value, value should not be equal to 0;

The same command on RouterOS,

/system script> print 
Flags: I - invalid 
 0   name="kaka" owner="admin" policy=ftp,reboot,read,write,policy,
test,winbox,password,sniff last-started=jan/01/1970
01:31:57 run-count=23 source=:beep 

/system script run 0