Manual:Create Certificates

Following is a step-by-step guide to creating your own CA (Certificate Authority) with openssl on Linux.

Generate certificates

Note: Starting from v5.15 RouterOS supports pkcs8 key format. If you are using older versions, to import keys in pkcs8 format run command:
openssl rsa -in myKey.key -text and write key output to new file. Upload new file to RouterOS and import

• First step is to build the CA private key and CA certificate pair.

  openssl genrsa -des3 -out ca.key 4096
  openssl req -new -x509 -days 3650 -key ca.key -out ca.crt
  

  During the process you will have to fill few entries (Common Name (CN), Organization, State or province .. etc). Created CA certificate/key pair will be valid for 10 years (3650 days).

• Now create private-key/certificate pair for the server

  openssl genrsa -des3 -out server.key 4096
  openssl req -new -key server.key -out server.csr
  
  openssl x509 -req -days 3650 -in server.csr -CA ca.crt -CAkey ca.key -set_serial 01 -out server.crt
  

  

  Warning: RSA Key length must be at least 472 bits if certificate is used by SSTP. Shorter keys are considered as security threats.

  
  

  And again during the process you will have to fill some entries. When filling CN remember that it must not match on CA and server certificate otherwise later naming collision will occur.

  

  Note: Common Name (CN) in server certificate should match the the IP address of your server otherwise you will get "domain mismatch" message and for example Windows SSTP client will not be able to connect to the server. If clients are only Windows machines then CN can be a DNS name, too.

  
  

  
  

• Client key/certificate pair creation steps are very similar to server. Remember to Specify unique CN.

  openssl genrsa -des3 -out client.key 4096
  openssl req -new -key client.key -out client.csr
  
  openssl x509 -req -days 3650 -in client.csr -CA ca.crt -CAkey ca.key -set_serial 01 -out client.crt
  

To examine certificate run following command:

openssl x509 -noout -text -in server.crt -purpose

Import certificates

To import newly created certificates to your router, first you have to upload server.crt and server.key files to the router via FTP. Now go to /certificate submenu and run following commands:

[admin@test_host] /certificate> import file-name=server.crt
passphrase: 
     certificates-imported: 1
     private-keys-imported: 0
            files-imported: 1
       decryption-failures: 0
  keys-with-no-certificate: 0
[admin@test_host] /certificate> import file-name=server.key 
passphrase: 
     certificates-imported: 0
     private-keys-imported: 1
            files-imported: 1
       decryption-failures: 0
  keys-with-no-certificate: 0

If everything is imported properly then certificate should show up with KR flag.

[admin@test_host] /certificate> print 
Flags: K - decrypted-private-key, Q - private-key, R - rsa, D - dsa 
 0 KR name="cert1" subject=C=LV,ST=RI,L=Riga,O=MT,CN=server,emailAddress=xxx@mt.lv 
      issuer=C=LV,ST=RI,L=Riga,O=MT,CN=MT CA,emailAddress=xxx@mt.lv serial-number="01"
      email=xxx@mt.lv invalid-before=jun/25/2008 07:24:33 
      invalid-after=jun/23/2018 07:24:33 ca=yes 

Note: If you want to use server certificates for OVPN or SSTP and use client certificate verification, then CA certificate must be imported, too.

[ Top | Back to Content ]