MikroTik SFP module compatibility table

This document clarifies compatibility between MikroTik made SFP modules and MikroTik RouterBOARD hardware

Model	S-GPON-ONU	S-RJ01	S+RJ10	S-85DLC05D	S-31DLC20D	S-3553LC20D	S+85DLC03D	S+31DLC10D	S+2332LC10D	SFP+ 1m/3m DAC
CCR1072-1G-8S+	+	+	+	+	+	+	+	+	+	+
CCR1036-12G-4S	+	+	-	+	+	+	+	+	+	+
CCR1036-8G-2S+	+	+	+	+	+	+	+	+	+	+
CCR1016-12S-1S+	+ 1	+ 1	+	+ 1	+ 1	+ 1	+	+	+	+
CCR1009-7G-1C	+	+	-	+	+	+	+	+	+	+
CCR1009-8G-1S-1S+	+	+	+	+	+	+	+	+	+	+
CCR1009-7G-1C-1S+	+	+	+	+	+	+	+	+	+	+
CRS125-24G-1S	+	+	-	+	+	+	+	+	+	+
CSS/CRS326-24G-2S+	+	+	+	+	+	+	+	+	+	+
CSS/CRS317-1G-16S+	+	+	+	+	+	+	+	+	+	+
CSS326-24G-2S+	+	+	+	+	+	+	+	+	+	+
CRS226-24G-2S+	+ 2	-	+	+ 2	+ 2	+ 2	+	+	+	+
CRS212-1G-10S-1S+	+ 1	+ 1	+	+ 1	+ 1	+ 1	+	+	+	+
CRS210-8G-2S+	+ 2	-	+	+ 2	+ 2	+ 2	+	+	+	+
CRS112-8G-4S	+	+	-	+	+	+	+	+	+	+
CRS109-8G-1S	+	+	-	+	+	+	+	+	+	+
CRS106-1C-5S	+	+	-	+	+	+	+	+	+	+
RB3011	+	+	-	+	+	+	+	+	+	+
RB2011	+	+	-	+	+	+	+	+	+	+
RB260	+	+	-	+	+	+	+	+	+	+
RB922/921	+	+	-	+	+	+	+	+	+	+
RB953GS	+	+	-	+	+	+	+	+	+	+
hAP AC	+	+	-	+	+	+	+	+	+	+
hEX PoE	+	+	-	+	+	+	+	+	+	+
FTC	+	+	-	+	+	+	+	+	+	+

Legend
Color codes:	Not supported	Check notes below

NOTES:

1. CCR1016-12S-1S+ / CRS212-1G-10S-1S+ -- SFP+1 interface does not work on any other link speed than 10G (does not support 1.25G fiber optic transceivers)
2. CRS226 / CRS210 -- Only SFP+1 interface supports SFP 1.25G fiber optic transceivers, SFP+2 works only with 10G transceivers/links.

Warning: Proper support for S-RJ01 modules on CCR1072-1G-8S+ is enabled only staring with v6.34rc software builds.

S-RJ01

Table that states in what link rates if mounted in specific MikroTik devices S-RJ01 module will be able to work.

Model	1000	100	10
RB3011	+	+	+
RB922	+	+	+
RB921	+	+	+
hAP ac	+	+	+
hEX PoE	+	+	+
RB953	+/+	+/-	+/-
RB2011	+	-	-
RB260	+	-	-
FTC	+	-	-
CRS106	+	+	+
CRS112	+	+	+
CRS125/CRS109	+	+	+
CRS212	+	+	+
CRS226/CRS210	-	-	-
CSS326/CRS326	+	-	+
CSS317/CRS317	+	-	+
CCR1009	+/+	+/+	+/+
CCR1016-12S-1S+	+	+	+
CCR1036-12G-4S	+	+	+
CCR1036-8G-2S+	+	+	+
CCR1072-1G-8S+	+	+	+

Notes:

• Rate works fine: +
• Rate does not work: -

• RB953: SFP2/SFP1
• CCR1009: SFP+/SFP

SFP+ interface compatibility settings with 1G links

For MikroTik devices with SFP+ interface that support both 10G and 1G link rate following settings are needed to be set on both linked devices for required interfaces. In order to get them working in 1G link rate.

• auto-negotiation disabled
• port speed 1G
• FD

Devices which SFP+ ports support 1G links:

• CCR1072-1G-8S+ - All SFP+ interfaces can be used in 1G mode if required.
• CCR1036-8G-2S+ - All SFP+ interfaces can be used in 1G mode if required.
• CCR1009-8G-1S-1S+ - All SFP+ interfaces can be used in 1G mode if required.
• CCR1009-7G-1C-1S+ - All SFP+ interfaces can be used in 1G mode if required.
• CSS326-24G-2S+RM - All SFP+ interfaces can be used in 1G mode if required.
• CRS226-24G-2S+ - Only SFP+1 supports 1G link speed, SFP+2 is for 10G links only.
• CRS210-8G-2S+ - Only SFP+1 supports 1G link speed, SFP+2 is for 10G links only.

Devices which SFP+ interfaces can be used only for 10G links:

• CCR1016-12S-1S+
• CRS212-1G-10S-1S+

SFP interface compatibility with 100M fiber links

Combo interface SFP part on below mentioned devices is compatible with fast ethernet fiber links.

Compatible devices:

• CCR1009-7G-1C
• CCR1009-7G-1C-1S+
• CRS106-1C-5S

S-GPON-ONU

Confirmed OLT device manufacturers that work with this GPON ONT module.

• ZTE
• Huawei
• Alcatel-Lucent
• Calix
• Adtran
• BDCOM

Some basic configuration examples for quick test:

• Huawei
• ZTE
• Adtran

Article: link

OSPF over S-GPON-ONU

To get OSPF network information forwarding working over GPON-ONU module NBMA network configuration must be used.