SwOS/CSS326

Summary

SwOS is an operating system designed specifically for administration of MikroTik switch products.

SwOS is configurable from your web browser. It gives you all the basic functionality for a managed switch, plus more: allows to manage port-to-port forwarding, broadcast storm control, apply MAC filter, configure VLANs, mirror traffic, apply bandwidth limitation and even adjust some MAC and IP header fields.

Warning: Each RouterBoard switch series device has its own firmware which cannot be installed on other series models! CSS326-24G-2S+ supports SwOS v2.0 and newer.

Connecting to the Switch

Open your web browser and enter IP address of your Switch (192.168.88.1 by default) and login screen will appear.

CSS326-24G-2S+ SwOS Login

SwOS default IP address: 192.168.88.1, user name: admin and there is no password.

Note: MikroTik Neighbor Discovery protocol tools can be used to discover IP address of Mikrotik switch. Manual:IP/Neighbor_discovery

Interface Overview

CSS326-24G-2S+ SwOS interface menu consists of multiple tabs: Link, SFP, SFP Status, Port Isolation, LAG, Forwarding, Stats, Errors, Histogram, VLAN, VLANs, Static Hosts, Hosts, SNMP, ACL, System and Upgrade.

Description of buttons in SwOS configuration tool:

• Append - add new item to the end of the list
• Apply All - applies current configuration changes
• Cut - removes item from the list
• Clear - resets properties of the item
• Discard Changes - removes unsaved configuration
• Insert - add new item to the list (places it before current item)
• Sort - sort VLAN table by VLAN-IDs; sort host table by MAC addresses

• Change Password - changes password of the switch
• Logout - logout from current Switch
• Reboot - reboot the switch
• Reset Configuration - reset configuration back to factory defaults
• Choose File - browse for upgrade or backup file
• Upgrade - upgrade firmware of the Switch
• Restore Backup - restore Switch using selected backup file
• Save Backup - generate and download backup file from the Switch

System

System Tab performs the following functions:

• General information about Switch
• Switch management
• Configuration reset
• Backup and restore configuration

Note: SwOS uses a simple algorithm to ensure TCP/IP communication - it just replies to the same IP and MAC address packet came from. This way there is no need for Default Gateway on the device itself.

CSS326-24G-2S+ General Settings

Property	Description
IP Address	IP address of the switch
Identity	Name of the switch (for Mikrotik Neighbor Discovery protocol)
Allow From	IP address from which the switch is accessible. Default value is '0.0.0.0/0' - any address
Allow From Ports	List of switch ports from which it is accessible
Allow From VLAN	VLAN ID from which the switch is accessible (VLAN Mode on ingress port must be other than disabled in order to connect)
Watchdog	Enable or disable system Watchdog. It will reset CPU of the switch in case of fault condition
Independent VLAN Lookup	Enable or disable independent VLAN lookup in the Host table for packet forwarding
Mikrotik Discovery Protocol	Enable or disable Mikrotik Neighbor Discovery protocol
MAC Address	MAC address of the switch (Read-only)
Serial Number	Serial number of the switch (Read-only)
Board Name	MikroTik model name of the switch (Read-only)
Uptime	Current switch uptime (Read-only)

Health and Global RSTP

CSS326-24G-2S+ Health and Global RSTP Settings

Property	Description
Temperature	Shows PCB temperature in celsius temperature scale (Read-only)

Property	Description
Bridge Priority (hex)	RSTP bridge priority for Root Bridge selection
Port Cost Mode	There are two methods for automatically detecting RSTP port cost depending on link speed. short: 10G - 2; 1G - 4; 100M - 10; 10M - 100 long: 10G - 2000; 1G - 20000; 100M - 200000; 10M - 2000000
Root Bridge	The priority and MAC address of the selected Root Bridge in the network (Read-only)

Password and Backup

CSS326-24G-2S+ System Management Settings

Link

Link Tab allows you to:

• Configure Ethernet and SFP+ ports
• Monitor link status of Ethernet and SFP+ ports

CSS326-24G-2S+ Link Settings

Property	Description
Enabled	Enable or disable port
Name	Editable port name
Link Status	Current link status (Read-only)
Auto Negotiation	Enable or disable auto negotiation
Speed	Specify speed setting of the port (requires auto negotiation to be disabled)
Full Duplex	Specify duplex mode of the port (requires auto negotiation to be disabled)
Flow control	Enable or disable 802.3x Flow control

SFP and SFP Status

SFP and SFP Status Tabs allow you to monitor status of SFP modules.

SFP Tab

SFP Status Tab

Port Isolation

Port Isolation table allows or restricts traffic forwarding between specific ports.

CSS326-24G-2S+ Port Isolation Tab

Note: It is possible to check/uncheck multiple checkboxes by checking one of them and then dragging horizontally (Click & Drag)

LAG

CSS326-24G-2S+ supports 802.3ad (LACP) compatible link aggregation as well as static link aggregation to ensure failover and load balancing based on Layer2 and Layer3 hashing.

Up to 16 link aggregation groups with up to 8 ports per a group are supported.

CSS326-24G-2S+ LAG Tab

Each individual port can be configured as an passive, active or static LACP using the control protocol.

Property	Description
Mode (default: passive)	Specify LACP packet exchange mode between ports: Passive: Place port in listening state, use LACP only when it's countrary port uses active LACP mode Active: Prefer to start LACP regardless countrary port mode Static: Place port in LACP mode=on

Property	Description
Group	Create static LACP group
Trunk (read only)	Represents group number port belongs to.
Partner (read only)	Represents partner mac-address.

Forwarding

Forwarding Tab provides advanced forwarding options among switch ports, port locking, port mirroring, bandwidth limit and broadcast storm control features.

CSS326-24G-2S+ Forwarding Settings

Property	Description
Port Lock	Port Lock - Enable or disable MAC address learning on this port Lock On First - Enable or disable MAC address learning on this port (MAC address from the first received packet will still be learnt)
Port Mirroring	Mirror Ingress - Whether traffic entering this port must be copied and forwarded to mirroring target port Mirror Egress - Whether traffic leaving this port must be copied and forwarded to mirroring target port Mirror To - Mirroring target port
Broadcast Storm Control	Storm Rate (%) - Limit the number of broadcast packets transmitted by an interface. The rate is measured in percents of the link speed. Include Unknown Unicast - Include unicast packets without an entry in host table in Storm Rate limitation
Bandwidth Limit	Ingress Rate - Limit traffic entering this port (bps)

RSTP

Per port RSTP configuration and monitoring is available in the RSTP menu.

CSS326-24G-2S+ RSTP Settings

Stats, Errors and Histogram

These menus provide detailed information about received and transmitted packets.

CSS326-24G-2S+ Port Statistics

CSS326-24G-2S+ Port Statistics

CSS326-24G-2S+ Port Statistics

VLAN and VLANs

VLAN configuration for switch ports.

CSS326-24G-2S+ Port VLAN Settings

VLAN membership configuration for switch ports.

CSS326-24G-2S+ VLAN Membership Settings

VLAN Configuration Example

Port based VLAN configuration with CSS326-24G-2S+

Static Hosts

Static host table entries. Static entries will take over dynamic if dynamic entry with same mac-address already exists. Also by adding a static entry you get access to some more functionality.

CSS326-24G-2S+ Static Host Table

Hosts

This table represents dynamically learnt MAC address to port mapping entries. When Switch receives a packet from certain port, it adds the packets source MAC address and port it received the packet from to host table, so when a packet comes in with certain destination MAC address it knows to which port it should forward the packet. If the destination MAC address is not present in host table then it forwards the packet to all ports in the group. Dynamic entries take about 5 minutes to time out. CSS326-24G-2S+ supports 16383 host table entries.

CSS326-24G-2S+ Host table

IGMP Snooping

IGMP Snooping which controls multicast streams and prevents multicast flooding is implemented in SwOS starting from version 2.5. The feature allows a switch to listen in the IGMP conversation between hosts and routers.

IGMP Snooping under System tab

Enable option under System tab.

CRS/CSS3XX series IGMP Snooping

Available IGMP snooping data:

• Group Adress
• VLAN
• Member Ports

CRS/CSS3XX series IGMP Snooping

Possibility to enable IGMP Snooping for concrete VLAN ID.

SNMP Tab

SwOS supports SNMP v1 and uses IF-MIB, SNMPv2-MIB and BRIDGE-MIB for SNMP reporting.

Available SNMP data:

• System information
• System uptime
• Port status
• Interface statistics
• Host table information

SNMP settings

Property	Description
Enabled	Enable or disable SNMP service
Community	SNMP community name
Contact Info	Contact information for the NMS
Location	Location information for the NMS

ACL Tab

An access control list (ACL) rule table is very powerful tool allowing wire speed packet filtering, forwarding and VLAN tagging based on L2,L3 protocol header field conditions.

CSS326-24G-2S+ ACL table

Each rule contains a conditions part and an action part.

Conditions part parameters

Property	Description
From	Port that packet came in from
MAC Src	Source MAC address and mask
MAC Dst	Destination MAC address and mask
Ethertype	Protocol encapsulated in the payload of an Ethernet Frame
VLAN	VLAN header presence: any present not present
VLAN ID	VLAN tag ID
Priority	Priority in VLAN tag
IP Src (IP/netmask:port)	Source IPv4 address, netmask and L4 port number
IP Dst (IP/netmask:port)	Destination IPv4 address, netmask and L4 port number
Protocol (integer)	IP protocol
DSCP	IP DSCP field

Action part parameters

Property	Description
Redirect To	Force new packets destination port
Mirror	Clones packet and sends it to mirror-target port
Rate	Limits bandwidth (bps)
Drop	Drop packet
Set VLAN ID	Changes the VLAN tag ID, if VLAN tag is present
Priority	Changes the VLAN tag priority bits, if VLAN tag is present

Reset and Reinstall

CSS326-24G-2S+RM has built-in backup SwOS firmware which can be loaded in case standard firmware breaks or upgrade fails:

• Holding Reset button for few seconds while CSS326-24G-2S+RM is booting resets configuration and loads backup firmware SwOS 2.0p.
  
• After loading backup firmware SwOS 2.0p it is possible to connect to 192.168.88.1 using web browser and install new SwOS firmware.