Supported Hardware
This page should be edited by the user community to reflect their tested hardware and version used.
Motherboards
| Model | ROS version | Result |
|---|---|---|
| Asrock Intel 82801G chipset | 3.0-3.14 | Bad performans, locks up under heavy load, suport multi cpu, not superted Pata, integradet ethernet not recognized. Maybe it's just Asrock bad motherboard dont know if the problem is in intel 82801G chipset tested on 2 motherbords, never tested on 2.9.x |
| ASUS P5B-Deluxe (Intel P965, 3xPCI, 3xPCI-E) | 3.13 | Works fine on Intel Core 2 Duo E6400. Not supported PATA controller. Both integrated Gigabit NIC (Marvell Yukon 88E8056 & 88E8001) works fine but only at 100Mbps. |
| ASUS P5B-V (Intel P965, 3xPCI, 4xPCI-E) | 3.13 | Works fine on Intel Dual Core E2180. Not supported PATA controller. Integrated Gigabit NIC Marvell Yukon 88E8001 works fine but only at 100Mbps. Winbox via MAC = problem, disconnects after 3 seconds. Winbox via IP no problem. |
| ASUS P5KC (Intel P35, 3x PCI, 3xPCI-E) | 3.10 | Not supported PATA controller (JMicron JMB363), ROS can boot from USB flash drive; internal ethernet not recognized. |
| ASUS P5GC-MX/1333 (2x PCI) | 3.7 | Works great for pentium dual-core e2160, hdd pata and sata, 1,5gb ram dual channel mode, except the attansic l2 ethernet onboard card is not recognized. |
| ASUS P5GC (6xPCI) | 2.9.39 | Ethernet recognized but not working |
| Asus A7V133-C | 3.0 beta 7 | Works fine |
| EPoX EP-4VKMI | 3.16 - 3.24 | Works fine. |
| Intel D815EGEW | 2.9.x | Excellent performance under 2.9. Not tested under v3. Onboard Ethernet Works perfectly. |
| Intel DG950 | 2.9.42 | Ethernet not recognized |
| Intel D945GCCRL | 2.9.43 & 3.0 beta 5 | Ethernet & DoM not recognized |
| Intel D945GCLF2 | 3.23 | 4 core's, 2gb ram, 32gb ssd, no problems. |
| Intel D945GCPE | 3.0 beta 9 | Work fine including integrated ethernet |
| Intel D945GCNL | 3.11 | Works fine but integrated ethernet (just disable) goes up and down on reboots multi-cpu= yes. shared IRQ for PCI devices, decrease nic performace. |
| Intel D945GNT | 2.9.45 | Works fine |
| Intel DQ965GFEKR (D41676) | 3.7, 3.4 | Works fine on 3.7/3.4 if multi-cpu=no, BUT 3.5-3.7 fail to boot with E4600 processor and multi-cpu=yes |
| Intel D845GVSRL | 3.7, 3.1, 2.9 | Very Stable, used for 4 years |
| Intel D945GZT-M | 3.0rc4 | Works fine |
| Chaintech AADF950 | 3.0 beta 5 | Works fine |
| Abit KT7E | 3.0 beta 7 | Works fine |
| ECS nForce3-A | 3.6 | Work fine including integrated ethernet |
| ECS P4M800PRO-M478 | 2.9.43 | No Apparent Problems, Disabled any unneeded devices in the BIOS |
| Abit BE6 | 2.9.43 | Works |
| Via EPIA-MII12000 | 2.9.42 | Locks up under heavy load across wireless |
| Intel DG965SWH | 3.0 beta 9 | Works fine, but only with SATA not IDE |
| Supermicro 5015M-MR | 2.9.28 | Motherboard is PDSMi w dual core |
| Supermicro PDSBM-LN2+ | 2.9.51 & 3.16 | http://forum.mikrotik.com/viewtopic.php?f=1&t=28184 |
| Supermicro PDSMi-LN4+ | 2.9.51, 3.13, 3.20 | Very stable even with dual-cores enabled. |
| Gigabyte GA-6BXS | 2.9.43 | Works fine |
| GigaByte GA-8I848P-G | 3.6 | Work fine including integrated ethernet |
| Gigabyte GA-8ST667 rev. 3.0 | 3.13 | Works fine; CPU Intel Celeron 2,4GHz; Chipset SiS 645DX; 5xPCI; |
| GigaByte K8-NS-ULTRA | 2.9.x-3.7 | Excelent work, including both onboard ethernet (100 and 1000 lan) |
| Epox 8RDA+ | 3.6 | Work fine including integrated ethernet |
| Chipset P35 (Tested Using Gigabyte GA-P35-DS3L & Abit IP35) | 3.7 | Work fine but only with SATA, not IDE (Include DOM), bellow v3.7 problem with SATA too |
| Microsoft Virtual PC 2007 | 3.7 | Installs and and tries to boot. |
| VMware Workstation v6.0.3 | 3.7 | Runs Wicked Fast! I have had up to 8 Ethernet interfaces running simultaneously. |
| Intel DG33FB | 3.7 | Works fine, Ethernet but not working (IRQ 9), set in BIOS Security/XD Tegnology to disable |
| DFI AD73 Pro (Chipset VIA KT266A/VT8233ACD) | 2.9.x-3.22 | Works fine. All 5 PCI's ocupied with 1 x LAN and 6 x R52H's (3 in RouterBoard11 and 3 in RouterBoard14!) |
| DFI AK75-EC (Chipset VIA KT133A/686B) | 3.14-3.22 | Stable. All PCI's ocupied with LAN, miniPCI-PCI adapters fitted with R52H's and XR5's |
| Gigabyte GA-MA770-DS3 (rev. 2.0) | 3.10 | Works fine and extreme stable include onboard LAN, IDE DOM can load normally |
| Fujitsu Siemens Primergy RX100S5 | 3.1, 3.7, 3.22 | Can Install from Netinstall with RAID (LSI) Controller enable. Can't install from CD and Netinstall with only SATA or PATA mode. But NOT RUN |
Ethernet chipsets
| Model | ROS version | Result |
|---|---|---|
| 3c905B Cyclone 100BaseTX | 2.9.51 | Works! Extremely reliable, doesn't fully support tagged vlans |
| 3cSOHO100-TX [Hurricane] (rev: 48) | 3.14rc1 | Works |
| 3c905C-TX/TX-M [Tornado] (rev: 120) | 2.9.51 | Works! Extremely reliable, doesn't fully support tagged vlans |
| 3c905C-TX/TX-M [Tornado] (rev: 116) | 2.9.51 | Works! Extremely reliable, doesn't fully support tagged vlans |
| 3c905B-FX Fast Etherlink XL FX 100baseFx [Cyclone] (rev: 0) | 2.9.43 | Works but no link in Winbox and no Graph in Dude !!!! |
| Intel S82557 10/100MBit | 2.9.43 | works |
| Intel PWLA8391GT PRO1000/GT | 3.7, 3.1, 2.9 | Extremely Stable, used for years |
| Intel PWLA8391GTL PRO1000/GT | 3.4 | Extremely Stable, used for years |
| Intel 82575EB & 8257GB | 3.15 | Added support |
| Intel S82557/S82555 10/100 Mbit TX | 2.9.50 / 3.16 | Works Stable! FCC ID:EJMNPDSPD035 |
| Intel PRO 1000 MT | 2.9.51 | Works |
| Intel 82541GI/PI Gigabit Ethernet Controller (rev: 5) | 2.9.49 | Working |
| Intel PRO/1000 PT ( 82572EI Gigabit Ethernet Controller rev: 6) | 3.13 | Works |
| Intel 10Gbit Ethernet PCI Express | 3.17 | Works |
| D-Link DFE-528TX rev. E1 | 3.13 | Works |
| D-Link DFE-580TX 4-port | 3.0 beta 5 | Bad card, not recommended. Hangs router |
| D-Link DFE-530/538TX | 2.9.43 | No apparent problems |
| D-Link DUB-E100 USB | 3.18 | added support, reported to be working |
| Marvell 88E8001 Gigabit Ethernet Controller (rev: 20) | 3.13 | Works |
| Marvell 88E8056 | 3.6 | reported to be working with some BIOS setting enabled |
| DECchip 21143 (ZYNX ZX410 4-port cPCI) | 2.9.51 | Working |
| Realtek Semiconductor/ RTL-8169 Gigabit Ethernet x4 (rev: 16) | 3.0-3.11 | Working Extremely reliable, used 4 mounts |
| Realtek RTL8111 (10/100/1000Mbit) | 3.10 | Seems to be working only in older RouterOS v3 releases, v3.10 and before. |
| Realtek RTL8139C+ | 3.14 | Works |
x86 Systems
| Model | ROS version | Result |
|---|---|---|
| Link Technologies, Inc - PowerRouter 732 | 2.9 and 3.0 | 1U Rackmount - 110-220Volt AC & -72V to -36V DC Power Options -- 7 Intel GigE Interfaces, with Dual-Core 3 Gig Intel Processor - 110,000+ MTBF -- Tested with over 2600 PPPoE Connections, over 300meg of Traffic without issues. Can Add Dual GigE Fiber Ports as well. Designed for Core and Tower Routing/PPPoE Server -- Caching capable of 1500+ users! |
| Link Technologies, Inc - PowerRouter 2242 | 3.0+ | Quad Core Intel Xeon Processor - 2U Rackmount -- Up to 22 Gigabit Interfaces - 10 Stock 10/100/1000 GigE Copper Interfaces, up to 12 More Copper or Fiber Interfaces. Dual Hot-Swap Power Supplies. |
| Link Technologies, Inc - PowerRouter 2282 | 3.0+ | Dual Quad Core Intel Xeon Processor - 2U Rackmount -- Up to 22 Gigabit Interfaces - 10 Stock 10/100/1000 GigE Copper Interfaces, up to 12 More Copper or Fiber Interfaces. Dual Hot-Swap Power Supplies. |
| Dell Optiplex GX1 | 2.9.x-3.0 | Intel onboard/cpu 450-600Mhz, eth:3com, best for wirless stations; uptime over 200d, no problems at all. |
| Compaq Presario 2282 | 2.9.43 | With 3c905 [Boomerang], no apparent problems |
| Dell GX100 | 2.9.x - 3.7 | Intel onboard, 2 free pci, Intel cpu |
| Dell GX240 | 2.9.x - 3.7 | Intel onboard, 2 free pci, Intel cpu, IDE HDD. |
| Dell GX260 | 2.9.x - 3.7 | Intel onboard, 2 free pci, Intel cpu, IDE HDD. |
| Dell GX270 | 2.9.x - 3.7 | Intel onboard, 2 free pci, Intel cpu. IDE HDD. |
| Dell GX280 | 2.9.x - 3.7 | Intel onboard, 2 free pci, Intel cpu, SATA HDD. |
| Dell Dimension XPS GEN 3 | 2.9.x | Lan Onboard, 4 free pci, Intel cpu , SATA HDD ( Excellent Stability ) |
| Dell Inspiron Desktop 518 | 2.9.x - 3.7 | After netinsall stuck on "loading system" |
| Dell PowerEdge 860 | 3.x | 1U Rackmount, 2x Broadcom Gigabit onboard, 1x Intel CPU (many options), 1 PCI/1 PCIe or 2 PCIe riser options, SATA HDD ONLY. (some issues with floppy netinstall) |
| Dell PowerEdge R200 | >= 3.19 recommended | Severe stability and clock issues with non-current ROS. Works like a top on 3.19 though. Also, if using an SATA-to-CF converter, the license key for the CF card in an R200 will only transfer to other R200's without Mikrotik reissuing it. |
| Dell PowerEdge 2950 | 3.x | 2U Rackmount, Optional Redundant Power Supplies, 2x Broadcom Gigabit onboard, 2x Intel CPU (many options), 2- 8xPCIe & 1- 4xPCIe Standard (other risers available), SATA HDD ONLY, 2x internal USB - MUST SPECIAL ORDER WITHOUT RAID CONTROLLER. (some issues with floppy netinstall)} |
| HP Proliant DL380 G5 | 3.17 | Works, but only if installed from CDROM (Netinstall to Windows mounted HDD causes issues) |
| Asus EEE PC 701 | 3.x | SFF Laptop, 1x10/100 ethernet (Not detected), Stock Wireless unsupported (AR5007E In Mini-PCIX slot), 630/900Mhz processor, 512MB RAM, 4GB SSD (Not detected), USB2.0 Bootable, SDHC Reader functions as a USB Stick |
| Dell PowerEdge SC1425 | 3.x | Rackmount, Intel Xeon 2.8 1MB 800FSB, 1024MB DDR2 PC3200 ECC, 2x Intel 82541GI Gigabit Ethernet, HD150gb SATA, USB works, very stable |
| Fujitsu Siemens Primergy RX100S5 | 3.7, 3.22 | Can Install from Netinstall with RAID (LSI) Controller enable. Can't install from CD and Netinstall with only SATA or PATA mode. But NOT RUN |
Embedded Controllers
| Model | ROS version | Result |
|---|---|---|
| WRAP.1E-2 | 2.9.51, 3.7 | 3 Ethernet, 1 miniPCI, 128 MB - Working |
| WRAP.2E | 2.9.51, 3.7, 3.9, 3.10 | 1 Ethernet, 2 MiniPCI, 128 MB - Work fine |
| ALIX 2-2 | 2.9.48 | 2 Ethernet, 2 miniPCI - Working |
| Adlink cPCI-6770 Low Power Pentium III | 2.9 and 3.0 | CompactPCI CPU Module - Working, excellent performance! |
| Advantech PCA-6751 | 2.9.49 | Working |
| Soekris 4801-50 | 2.9.48 | 3 Ethernet, 128MB, CF 512MB - Working |
| Soekris 4826-48 | 3.10 | 233 Mhz CPU, 128 Mbyte SDRAM, 1 Ethernet, 1 Serial, 256 Mbyte CF Flash, 2 Mini-PCI sockets, PoE. Limited power available/runs only 1 high power card (@26dB) along with another lower power card (@17dB) |
| Soekris net4801-48/50 + lan1641 | 3.22 | All 7 (3+4) ethernet works, USB works (tested with Huawei 3G modem), extra serial port works. And RouterOS installed on CF card. |
| ALIX 2C0 | 2.9,3.0 | 2 Ethernet, 2 miniPCI ,128Mb 433Mhz Amd Geode- Working Perfect |
| ALIX 2C1 | 2.9,3.0 | 2 Ethernet, 2 miniPCI ,128Mb 433Mhz Amd Geode- Working Perfect |
| ALIX 2C3 | 2.9,3.0 | 2 Ethernet, 2 miniPCI ,256Mb 500Mhz Amd Geode- Working Perfect |
| ALIX 3C1 | 2.9,3.0 | 2 Ethernet, 2 miniPCI ,128Mb 433Mhz Amd Geode- Working Perfect |
| ALIX 3C2 | 2.9,3.0 | 2 Ethernet, 2 miniPCI ,256Mb 500Mhz Amd Geode- Working Perfect |
3G cards
| Model | ROS version | Result |
|---|---|---|
| AirPrime/Sierra PC 5220! | v3 | |
| AnyData ADU E100A
(aka "USB Wireless HSDPA/UMTS 2.1GHz GSM/GPRS/EGPRS 900/17000MHz/CDMA 1x EVDO Rev.A") |
v3.14 | |
| AnyData ADU 500A USB
(aka "USB Wireless HSDPA/UMTS 2.1GHz GSM/GPRS/EGPRS 900/1800MHz/CDMA 1x EVDO Rev.A") |
v3.14 | |
| Audiovox PC5220 CDMA Dual Band 1XEV-DO PC Card | v3 | |
| C-motech CNU-680 CDMA 1x EV-DO 450Mhz USB Modem (used by Triatel) | v3.22 | |
| Huawei E226 USB modem, | 3.25 | |
| Huawei E220 USB modem, E200BIS | 3.0rc8 | |
| Huawei E169 USB modem (used by Tele2) | 3.22 | |
| Huawei E180 USB modem | 3.20 | |
| Huawei E1550 | v3.26 | |
| Siemens M20 | v3.28 | |
| Huawei Mobile Connect Model E620 (3G); | v3 | |
| Kyocera KPC650 | v3 | |
| Novatel EU740 | v3 | |
| Novatel EU870 | v3 | |
| Novatel EV620 CDMA/EV-DO | v3 | |
| Novatel Merlin ES620 / Merlin ES720 / Ovation U720 | v3 | |
| Novatel Merlin ES620 SM Bus | v3 | |
| Novatel Merlin S720 (HSDPA); | v3 | |
| Novatel Merlin XU870 HSDPA/3G | v3 | |
| Novatel U730 (Wireless HSDPA Modem) | v3 | |
| Novatel Wireless CDMA card | v3 | |
| Option Fusion UMTS Quad-GPRS (Vodafone Globetrotter); | v3.4 | |
| Option Globetrotter HSDPA USB (aka Teltonika ModemUSB/H7.2 U3G150) | v3 | |
| Option Qualcomm 3G WCDMA Model M00201-10886 miniPCI-e | v3.27 | works also in RouterBOARD with miniPCI-e slot and SIM slot (SIM slot required) |
| Sierra Aircard 595 | v3 | |
| Sierra Aircard 595U USB Sprint Card | v3 | |
| Sierra Wireless AirCard 580 | v3 | |
| Sierra Wireless AirCard 595 | v3 | |
| Sierra Wireless AirCard 597E | v3 | |
| Sierra Wireless AirCard 597E | v3 | |
| Sierra Wireless AirCard 875 | v3 | |
| Sierra Wireless AirCard 880 | v3.8 | |
| Sierra Wireless AirCard 880 E | v3.8 | |
| Sierra Wireless AirCard 881 | v3.8 | |
| Sierra Wireless AirCard 881 E | v3.8 | |
| Sierra Wireless EM5625 | v3 | |
| Sierra Wireless MC5720 | v3 | |
| Sierra Wireless MC5720 | v3 | |
| Sierra Wireless MC5725 | v3 | |
| Sierra Wireless MC8755 | v3 | Users have reported that the device doesn't show up after shutdown, reboot is required |
| Sierra Wireless MC8755 for Europe | v3 | |
| Sierra Wireless MC8765 | v3 | |
| Sierra Wireless MC8775 | v3 | |
| Sierra Wireless MC8780 | v3.8 | |
| Sierra Wireless MC5725 | v3.18 | |
| Sierra Wireless MC5727 | v3.18 | |
| Sierra Wireless MC8785 | v3.18 | |
| Sierra Wireless MC8790 | v3.18 | |
| Sierra Wireless MC8790 | v3.18 | |
| Sierra Wireless MC8781 | v3.8 | |
| Sierra Wireless Sierra 598 (Sprint) USB | v3.x | |
| Sierra Wireless MP3G - EVDO | v3.8 | |
| Sierra Wireless MP3G - UMTS/HSPA | v3.8 | |
| Silicon Labs MobiData GPRS USB Modem | v3.22 | |
| Verizon Express Network PC5220 (AirPrime 5220) | v3 | |
| ZTE AC8700 | v3.6 | |
| ZTE MF620 / MF622 | v3 | |
| ZTE MF620 / MF622 (3G) | v3.6 | |
| T-Mobile (Germany) Web´n´Walk Box Micro (Huawei E220) | v3.x | |
| Vodafone (Germany) Easybox 2 (Huawei E220) | v3.x | |
| O2 (Germany) Surfbox Mini (Huawei E220) | v3.x | |
| E-Plus & Base (Germany) USB Minimodem (Huawei E220) | v3.x | |
| Huawei E600 | v3.15 | |
| Novatel Merlin V640/XV620 | v3.15 | |
| Novatel Merlin V620/S620 | v3.15 | |
| Novatel Merlin EX720/V740/X720 | v3.15 | |
| Novatel Merlin V720/S720/PC720 | v3.15 | |
| Novatel Merlin XU870 HSDPA/3G | v3.15 | |
| Novatel X950D | v3.15 | |
| Novatel ES620/ES720/U720/USB720 | v3.15 | |
| Novatel E725/E726 | v3.15 | |
| Vodafone EU740/Novatel non-Vodafone EU740 | v3.15 | |
| Vodafone K3565/Huawei E160 | v3.23 | |
| Novatel EU850D/EU860D/EU870D | v3.15 | |
| Novatel MC930D/MC950D | v3.15 | |
| Novatel MC727/U727/USB727 | v3.15 | |
| Novatel Expedite EV620 CDMA/EV-DO | v3.15 | |
| Novatel Expedite EU740 HSDPA/3G, Dell Wireless 5500 Mobile/Dell Wireless 5505 Mobile | v3.15 | |
| Novatel Expedite E720 CDMA/EV-DO | v3.15 | |
| Novatel Expedite ET620 CDMA/EV-DO | v3.15 | |
| Onda H600/ZTE MF330 | v3.15 | |
| BP3-USB & BP3-EXT HSDPA | v3.15 | |
| ZTE MY 39 (MSM 6500 based) | v3.20 | |
| Cricket A600 | v3.26 | |
| Globetrotter HSDPA Modem Option N.V. | v3.26 | |
| Sony Ericsson MD300 | v3.26 | |
| ZTE MF 626 | v3.26 | |
| ZTE MF 627 | v3.26 | |
| Pantech / UTStarcom UM175 | v3.27 | On Alltel's CDMA EVDO RevA network average 700-800kbps up and 2.4-2.8Mbps down |
Memory cards
NB! New flash cards need always formatting!
Legend:
- V - works
- X - doesn't work
- ? - not tested
- NA - not available for this RB
| Model | Type | RB600 | RB1000 | RB433AH | RB450G |
|---|---|---|---|---|---|
| PQI 4GB 120x HiSpeed | CF | X | ? | NA | ? |
| 2GB Kingston 133x (Elite Pro, code CF/2GB-S2) | CF | V | ? | NA | ? |
| 4GB Kingston CF/4GBIN | CF | X | ? | NA | ? |
| 8GB A-Data Speedy G08GNMC7B0095 | CF | V | V | NA | ? |
| 16GB A-Data Speedy | CF | V | V | NA | ? |
| 4GB Apacer Photo Steno IV 300X | CF | X | X | NA | ? |
| 1GB Sandisk Ultra II BB05024GA | CF | V | V | NA | ? |
| 8GB Sandisk Ultra II | CF | ? | V | NA | ? |
| 2.5GB Seagate ST1 (ST625211CF) | CF microdrive | V | V | NA | ? |
| 8GB Seagate ST1 | CF microdrive | V | V | NA | ? |
| 64MB Nokia | microSD | NA | NA | ? | V |
| 512MB Kingston | microSD | NA | NA | V | ? |
| 1GB Apacer | microSD | NA | NA | V | ? |
| 2GB Kingston | microSD | NA | NA | X | X |
| 2GB Traxdata | microSD | NA | NA | ? | V |
| 4GB Axiz | microSD | NA | NA | V | ? |
| 4GB Kingston | microSD | NA | NA | V | ? |
| 4GB Kingston SDHC (C04G JAPAN class 4) | microSD | NA | NA | V | ? |
| 4GB Transcend SDHC | microSD | NA | NA | V | ? |
| 8GB Sandisk SDHC (0733702482DLE) | microSD | NA | NA | V | V |
| 8GB Kingston SDHC (Class 4) | microSD | NA | NA | V | ? |
Note: Pushing the "Kingston SDHC 8GB card" all the way into the socket caused the card not to work properly! It had to be pulled out ~1mm for it to work!
802.11a/b/g wireless cards
| Model | Form factor | Platform | ROS | Result |
|---|---|---|---|---|
| Alfa AWPCI 085 H | miniPCI | RB1xx/RB333/RB4xx/x86 | 2.9&3.x | All just perfect |
| TP-Link TL-WN550/551 | PCI | x86 | 2.9&3.x | Perfect 19dB rated, stable at 21 |
| TP-Link TL-WN650/651 | PCI | x86 | 2.9&3.x | Perfect 19dB rated, stable at 21. Unstable with compression activated |
| D-Link AG530 a/b/g (both rev.A1 and A2) | PCI | x86 | 2.9&3.x | Perfect. Works perfect, in both 2.4 and 5.x GHz |
| Gigabyte b/g GN-WI01GT | miniPCI-e | x86 | 3.x | Works also in RouterBOARDs with miniPCI-e slot |
| Senao NL-2511CD EXT2 | PCMCIA | x86&rb230 | only 2.9x tested | Perfect. Just about the most sensitive card i used, in the good sense. Only 11b. |
| Netgear WG311T 108 | PCI | x86 | only 2.9x tested | Perfect. stability |
| SMC SMCWPCIT-G | PCI | x86 | 3.x tested | Perfect on A/B/G. |
| Wistron DCMA-81 | miniPCI | x86,rb | 2.9.xx, 3.xx | Perfect on A/B/G with or without compression. |
| Wistron DCMA-82 | miniPCI | rb | 3.xx | Works on some RB, but on 2/3 of my RB433 it causes the board to reboot when enabled. Many other people have had similar experiences. Not recommended. Maybe OK on 133 |
| Senao NMP-8602 | miniPCI | x86&rb411 | 2.9x,3.x tested | Perfect on a/b/g |
| Ubiquiti XR2 | miniPCI | RB433 | 3.x | works as advertised, too thick for 3 in rb433 |
| Ubiquiti XR5 | miniPCI | RB433, x86 | 3.x | works as advertised, too thick for 3 in rb433 |
| Ubiquiti SR9 | miniPCI | RB433 | 3.x | works as advertised, thin enough to load 3 in RB433 |
| Ubiquiti XR9 | miniPCI | RB433 | 3.x | works as advertised, thin enough to place cards above, but antenna port may contact cards below |
802.11n wireless cards
| Model | Form factor | ROS | Result |
|---|---|---|---|
| RouterBOARD R2N | miniPCI | 4.0b3 | works |
| RouterBOARD R52N | miniPCI | 4.0b3 | works |
| TP-Link Wireless N (2T2R) | miniPCI | 4.0b3 | works |
| Ubiquiti SR71-A | miniPCI | 4.0b3 | works |
T1/E1
| Model | Form factor | Platform | ROS | Result |
|---|---|---|---|---|
| Farsite FarSync TE1 | PCI | x86 | 3.15 | supported |
Note: Since v3.15 RouterOS doesn't support any Sync/T1/E1 cards except select Farsite models