Manual:IPv6/DHCP Client

Applies to RouterOS: v5.9 +

Summary

Currently DHCPv6 client can receive only delegated prefix from DHCPv6-PD server.

Quick setup example

This simple example demonstrates how to enable dhcp client to receive IPv6 prefix and add it to the pool.

/ipv6 dhcp-client add pool-name=test-ipv6 pool-prefix-length=64 interface=ether13

Detailed print should show status of the client and we can verify if prefix is received

[admin@x86-test] /ipv6 dhcp-client> print detail 
Flags: D - dynamic, X - disabled, I - invalid 
 0    interface=bypass pool-name="test-ipv6" pool-prefix-length=64 status=bound 
      prefix=2001:db8:7501:ff04::/62  expires-after=2d23h11m53s 

Notice that server gave us prefix 2a02:610:7501:ff04::/62 . And it should be also added to ipv6 pools

[admin@MikroTik] /ipv6 pool> print 
Flags: D - dynamic 
 #   NAME                         PREFIX                                      PREFIX-LENGTH
 0 D test-ipv6                    2001:db8:7501:ff04::/62                                64

It works! Now you can use this pool, for example, for pppoe clients.

Properties

Sub-menu: /ipv6 dhcp-client

Property	Description
comment (string; Default: )	Short description of the client
disabled (yes | no; Default: no)
interface (string; Default: )	Interface on which DHCPv6 client will be running.
pool-name (string; Default: )	Name of the IPv6 pool in which received IPv6 prefix will be added
pool-prefix-length (string; Default: )	Prefix length parameter that will be set for IPv6 pool in which received IPv6 prefix is added. Prefix length must be greater than the length of received prefix, otherwise prefix-length will be set to received prefix length + 8 bits.

Status

Command /ipv6 dhcp-client print detail will show current status of dhcp client and read-only properties listed in table below:

Property	Description
dynamic (yes | no)
expires-after (time)	Time when the IPv6 prefix expires (specified by the DHCPv6 server).
invalid (yes | no)	Shows whether configuration is invalid.
prefix (IPv6 prefix)	Shows received IPv6 prefix from DHCPv6-PD server
status (stopped | searching | requesting... | bound | renewing | rebinding | error | stopping)	Shows the status of DHCPv6 Client: stopped - dhcpv6 client is stopped searching - sending "solicit" and trying to get "advertise" requesting - sent "request" waiting for "reply" bound - received "reply". Prefix assigned. renewing - sent "renew", waiting for "reply" rebinding - sent "rebind", waiting for "reply" error - reply was not received in time or some other error ocurred. stopping - sent "release"

Menu specific commands

Property	Description
release (numbers)	Release current binding and restart DHCPv6 client
renew (numbers)	Renew current leases. If the renew operation was not successful, client tries to reinitialize lease (i.e. it starts lease request procedure (rebind) as if it had not received an IP address yet)

Application Examples

Use received prefix for local RA

Consider following setup:

• ISP is routing prefix 2001:DB8::/62 to the router R1
• Router R1 runs DHCPv6 server to delegate /64 prefixes to the customer routers CE1 CE2
• DHCP client on routers CE1 and CE2 receives delegated /64 prefix from the DHCP server (R1).
• Client routers uses received prefix to set up RA on the local interface

Configuration

R1

/ipv6 pool
add name=myPool prefix=2001:db8::/62 prefix-length=64

/ipv6 dhcp-server
add address-pool=myPool disabled=no interface=to-CE-routers lease-time=3m name=server1

CE1

/ipv6 dhcp-client
add interface=to-R1 pool-name=my-ipv6

/ipv6 address
add address=::1/64 from-pool=my-ipv6 interface=to-clients advertise=yes

CE2

/ipv6 dhcp-client
add interface=to-R1 pool-name=my-ipv6

/ipv6 address
add address=::1/64 from-pool=my-ipv6 interface=to-clients advertise=yes

[ Top | Back to Content ]