MikroTik wired interface compatibility

From MikroTik Wiki
Revision as of 11:49, 11 September 2023 by Vjaceslavsa (talk | contribs) (→‎S-RJ01)
Jump to navigation Jump to search

MikroTik SFP/SFP+/SFP28/QSFP+/QSFP28 compatibility

Note: MikroTik devices and SFP/SFP+/SFP28/QSFP+/QSFP28 modules do not have any restrictions for other vendor equipment.

As long as the other vendor modules and devices comply with transceiver multi-source agreement (MSA) they should be compatible with MikroTik.


1G SFP

Model S-RJ01 S-85DLC05D S-31DLC20D S-3553LC20D S-55DLC80D S-4554LC80D SFP CWDM SFP 1m/3m DAC S+AO0005 AOC SFP28 1m/3m DAC
CCR1072-1G-8S+ + + + + + + + + + +
CCR1036-12G-4S + + + + + + + + + +
CCR1036-8G-2S+ + + + + + + + + + +
CCR1016-12S-1S+ + 1 + 1 + 1 + 1 + 1 + 1 + + + +
CCR1009-7G-1C + + + + + + + + + +
CCR1009-8G-1S-1S+ + + + + + + + + + +
CCR1009-7G-1C-1S+ + + + + + + + + + +
CCR2004-1G-2XS-PCIe - - - - - - - - - -
CCR2004-1G-12S+2XS + + + + + + + + + +
CCR2004-16G-2S+ + + + + + + + + + +
CCR2116-12G-4S+ + + + + + + + + + +
CCR2216-1G-12XS-2XQ + + + + + + + + + +
CRS125-24G-1S + + + + + + + + + +
CRS305-1G-4S+ + + + + + + + + + +
CRS309-1G-8S+ + + + + + + + + + +
CRS312-4C+8XG - + + + + + + + + +
CRS318-1Fi-15Fr-2S + + + + + + + + + +
CRS318-16P-2S+ + + + + + + + + + +
CRS326-24S+2Q+ + + + + + + + + + +
CRS354-48G/P-4S+2Q+ + + + + + + + + + +
CRS518-16XS-2XQ + + + + + + + + + +
CRS510-8XS-2XQ + + + + + + + + + +
CSS/CRS326-24G-2S+ + + + + + + + + + +
CRS317-1G-16S+ + + + + + + + + + +
CRS328-4C-20S-4S+ + + + + + + + + + +
CRS328-24P-4S+ + + + + + + + + + +
CRS226-24G-2S+ - + 2 + 2 + 2 + 2 + 2 + + + +
CRS212-1G-10S-1S+ + 1 + 1 + 1 + 1 + 1 + 1 + + + +
CRS210-8G-2S+ - + 2 + 2 + 2 + 2 + 2 + + + +
CRS112-8G/P-4S + + + + + + + + + +
CRS109-8G-1S + + + + + + + + + +
CRS106-1C-5S/FiberBox + + + + + + + + + +
RB5009 + + + + + + + + + +
RB4011 + + + + + + + - + +
RB3011 + + + + + + + + + +
RB2011 + + + + + + + + + +
L009 + + + + + + + + 14 + 14 + 14
RB260/CSS106 + + + + + + + + + +
RB922/921 + + + + + + + + + +
RB953GS + + + + + + + + + +
hAP AC + + + + + + + + + +
hEX PoE/PowerBox Pro + + + + + + + + + +
hEX S + + + + + + + + + +
RBFTC11 + + 8 + 8 + 8 + 8 + 8 + 8 + 8 + 8 + 8
LHG XL 52 ac - + + + + + + + + +
RBD22/D23

mANTBox 52 15s/NetMetal ac²

- + + + + + + + + +
CSS610 + + + + + + + + + +
CRS310-1G-5S-4S+/netFiber 9 + + + + + + + + + +
CRS310-8G+2S+IN + + + + + + + + + +

10G SFP+/25G SFP28

Model S+RJ10 S+85DLC03D S+31DLC10D S+2332LC10D SFP+ CWDM SFP+ 1m/3m DAC S+AO0005 AOC Q+BC0003-S+ XQ+BC0003-XS+ SFP28 1m/3m DAC SFP28 XS+31LC10D SFP28 XS+2733LC15D
CCR1072-1G-8S+ + + + + + + + + 5 + 5 + + +
CCR1036-12G-4S - + + + + + + - - + + +
CCR1036-8G-2S+ + + + + + + + + 5 + 5 + + +
CCR1016-12S-1S+ + 10 + + + + + + + 1,5 + 1,5 + + +
CCR1009-7G-1C - + + + + + + - - + + +
CCR1009-8G-1S-1S+ + 10 + + + + + + + 5 + 5 + + +
CCR1009-7G-1C-1S+ + + + + + + + + 5 + 5 + + +
CCR2004-1G-2XS-PCIe + + + + + + + + 5 + 5 + + +
CCR2004-1G-12S+2XS + 11 + + + + + + + 5 + 5 + + +
CCR2004-16G-2S+ + + + + + + + + 5 + 5 + + +
CCR2116-12G-4S+ + + + + + + + + 5 + 5 + + +
CCR2216-1G-12XS-2XQ + + + + + + + + + + + +
CRS125-24G-1S - + + + + + + - - + + +
CRS305-1G-4S+ + 7 + + + + + + + 5 + 5 + + +
CRS309-1G-8S+ + 4 + + + + + + + 5 + 5 + + +
CRS312-4C+8XG + + + + + + + + 5 + 5 + + +
CRS318-1Fi-15Fr-2S - + + + + + + - - + + +
CRS318-16P-2S+ + + + + + + + + 5 + 5 + + +
CRS326-24S+2Q+ + 6 + + + + + + + + + + +
CRS354-48G/P-4S+2Q+ + + + + + + + + + + + +
CRS518-16XS-2XQ + + + + + + + + + + + +
CRS510-8XS-2XQ + + + + + + + + + + + +
CSS/CRS326-24G-2S+ + + + + + + + + 5 + 5 + + 9 + 9
CRS317-1G-16S+ + 3 + + + + + + + 5 + 5 + + +
CRS328-4C-20S-4S+ + 10 + + + + + + + 5 + 5 + + +
CRS328-24P-4S+ + + + + + + + + 5 + 5 + + 9 + 9
CRS226-24G-2S+ + + + + + + + + 5 + 5 + + +
CRS212-1G-10S-1S+ + 10 + + + + + + + 5 + 5 + + +
CRS210-8G-2S+ + + + + + + + + 5 + 5 + + +
CRS112-8G/P-4S - + + + + + + - - + + +
CRS109-8G-1S - + + + + + + - - + + +
CRS106-1C-5S/FiberBox - + + + + + + - - + + +
RB5009 + + + + + + + + 5 + 5 + + +
RB4011 + + + + + - + - - + + +
RB3011 - + + + + + + - - + + +
RB2011 - + + + + + + - - + + +
L009 - + 14 + 14 + 14 + 14 + 14 + 14 + 14 + 14 + 14 + 14 + 14
RB260/CSS106 - + + + + + + - - + + +
RB922/921 - + + + + + + - - + + +
RB953GS - + + + + + + - - + + +
hAP AC - + + + + + + - - + + +
hEX PoE/PowerBox Pro - + + + + + + - - + + +
hEX S - + + + + + + - - + + +
RBFTC11 - + 8 + 8 + 8 + 8 + 8 + 8 - - + 8 + 8 + 8
LHG XL 52 ac - + + + + + + - - + + +
RBD22/D23

mANTBox 52 15s/NetMetal ac²

- + + + + + + - - + + +
CSS610 + + + + + + + + 5 + 5 + + +
CRS310-1G-5S-4S+/netFiber 9 + 10 + + + + + + + 5 + 5 + + +
CRS310-8G+2S+IN + + + + + + + + 5 + 5 + + +

40G QSFP+

Model QSFP+ Q+DA0001 Q+85MP01D Q+BC0003-S+
CRS326-24S+2Q+ + + +
CRS354-48G/P-4S+2Q+ + + +
CRS504-4XQ-IN + + +
CRS504-4XQ-OUT +13 + +13
CRS518-16XS-2XQ + + +
CRS510-8XS-2XQ + + +
CCR2216-1G-12XS-2XQ + + +

100G QSFP28

Model XQ+31LC10D XQ+31LC02D XQ+85MP01D XQ+DA0001 XQ+DA0003 XQ+BC0003-XS+
CRS326-24S+2Q+ - - + + + +
CRS354-48G/P-4S+2Q+ - - + + + +
CRS504-4XQ-IN + + + + + +
CRS504-4XQ-OUT + + + +13 +13 +13
CRS518-16XS-2XQ + + + + + +
CRS510-8XS-2XQ + + + + + +
CCR2216-1G-12XS-2XQ + + + + + +


Legend
Color codes: Not supported Check notes below


NOTES:

  1. CCR1016-12S-1S+, CRS212-1G-10S-1S+ -- SFP+1 interface does not work on any other link speed than 10G (does not support 1.25G fiber optic transceivers)
  2. CRS226-24G-2S+, CRS210-8G-2S+ -- Only SFP+1 interface supports SFP 1.25G fiber optic transceivers, SFP+2 works only with 10G transceivers/links.
  3. CSS/CRS317-1G-16S+ -- power controller supports up to 10 simultaneous S+RJ10 modules.
  4. CSS/CRS309-1G-8S+ -- 8x S+RJ10 are supported if PoE-in Voltage >30V. Up 4x S+RJ10 are supported when PoE-in Voltage = 24V.
  5. Q+BC0003-S+, XQ+BC0003-XS+ -- SFP+ connector support in the SFP+/SFP28 cages
  6. CSS/CRS326-24S+2Q+ -- supports up to 12 simultaneous S+RJ10 modules.
  7. CSS/CRS305-1G-4S+ -- supports up to 2 simultaneous S+RJ10 modules.
  8. RBFTC11 -- works connected to other device 1G SFP port.
  9. XS+31LC10D, XS+2733LC15D -- full support has been added to CSS/CRS326-24G-2S+ and CRS328-24P-4S+ switches manufactured from October 2021.
  10. S+RJ10 -- support in the SFP+ cages.
  11. CCR2004-1G-12S+2XS -- supports up to 6 simultaneous S+RJ10 modules.
  12. CCR2004-1G-2XS-PCIe -- supports only the same speed in both SFP28 ports (2 x 25G or 2 x 10G modes).
  13. CRS504-4XQ-OUT -- reduce IP code from IP66 to IP54.
  14. L009 -- supports up to 2.5G rate (works with forced speed mode).

S-RJ01

Table that states in what link rates if mounted in specific MikroTik devices S-RJ01 module will be able to work. Use these modules only with auto-negotiation enabled, forced link speeds are not supported. They will negotiate to correct duplex and highest possible rate.

Model 1000 100 10
RB5009 + + +
RB4011 + + +
RB3011 + + +
RB922 + + +
RB921 + + +
hAP ac + + +
hEX PoE + + +
hEX S + - -
RB953 +/+ -/+ -/+
RB2011 + - -
RB260/CSS106 + - -
RBFTC11 + - -
LHG XL 52 ac - - -
RBD22/D23

mANTBox 52 15s/NetMetal ac²

- - -
CRS106 + + +
CRS112 + + +
CRS125/CRS109 + + +
CRS212 + + +
CRS226/CRS210 - - -
CSS/CRS305-1G-4S+ + + +
CSS/CRS309-1G-8S+ + + +
CRS318-1Fi-15Fr-2S + + +
CRS318-16P-2S+ + + +
CSS/CRS326-24G-2S+ + + +
CRS354 + + +
CSS/CRS328-4C-20S-4S+ + + +
CSS/CRS328-24P-4S+ + + +
CSS/CRS317-1G-16S+ + + +
CRS326-24S+2Q+ + + +
CSS610 + + +
CRS310-1G-5S-4S+/netFiber 9 + + +
CRS310-8G+2S+IN + + +
CCR1009 +/+ +/+ +/+
CCR1016-12S-1S+ + + +
CCR1036-12G-4S + + +
CCR1036-8G-2S+ + + +
CCR1072-1G-8S+ + + +

Notes:

  • Rate works fine: +
  • Rate does not work: -
  • RB953: SFP1/SFP2
  • CCR1009: SFP+/SFP

10 Gigabit Ethernet

S+RJ10

Use these modules only in 10G SFP+ ports with auto-negotiation enabled, forced link speeds and configurable link speed advertisements are not supported. They will negotiate to correct duplex and highest possible rate. For proper S+RJ10 module installation and recommended use case scenarios, please read S+RJ10 General Guidance.

Speed Cable type S+RJ10 to Ethernet port
10BASE-T Cat5e/6 100m
100BASE-T Cat5e/6 100m
1000BASE-T Cat5e/6 100m
2.5GBASE-T Cat5e/6 UTP 100m
2.5GBASE-T Cat5e/6 STP 100m
5GBASE-T Cat5e/6 100m
10GBASE-T Cat6/7 30m

Note: Negotiated speed highly depends on quality and length of the cables that are used.


Note: S+RJ10 to S+RJ10 always will negotiate to highest possible rate.


The latest revision of S+RJ10 contains "/r2" by the end of serial number. It comes with following improvements:

  • Jumbo frames up to 10218 Bytes at 2.5G, 5G and 10G speeds;
  • Actual link speed reporting;
  • DDM monitoring (Supply Voltage, Module temperature).
Link Speed Max MTU
10Gbps 10218
5Gbps 10218
2.5Gbps 10218
1000Mbps 1504
100Mbps 1504
10Mbps 1504

CRS312-4C+8XG

10GE ports maximum supported cable length.

Speed Cable type 10 Gigabit Ethernet ports
10BASE-T Cat5e/6 100m
100BASE-T Cat5e/6 100m
1000BASE-T Cat5e/6 100m
2.5GBASE-T Cat5e/6 100m
5GBASE-T Cat5e/6 100m
10GBASE-T Cat6/7 30m

Note: Negotiated speed highly depends on quality and length of the cables that are used.


Warning: 10GE ports doesn't support Half duplex mode with forced link speeds.


SFP interface compatibility with 100M optical transceivers

SFP interface on the listed devices is compatible with fast ethernet fiber links.

Compatible devices (interface):

  • CCR1009-7G-1C (combo1)
  • CCR1009-7G-1C-1S+ (combo1)
  • CRS106-1C-5S (combo1)
  • CRS328-4C-20S-4S+ (combo1 - combo4 and SFP1 - SFP20)
  • LHG XL 52 ac
  • RBD22/D23/mANTBox 52 15s/NetMetal ac²

SFP+ interface compatibility with 1G optical transceivers

For MikroTik devices with SFP+ interface that support both 10G and 1G link rate following settings must be set on both linked devices for required interfaces. These settings only relate when optical SFP transceivers are used. In order to get them working in 1G link rate, use the following configuration: 

/interface ethernet set sfp-sfpplus1 auto-negotiation=no speed=1Gbps full-duplex=yes
  • auto-negotiation disabled
  • port speed 1G
  • full-duplex

Devices which SFP+ ports support 1G links:

  • CCR2004-1G-12S+2XS - All SFP+ interfaces can be used in 1G mode if required.
  • CCR2004-16G-2S+ - All SFP+ interfaces can be used in 1G mode if required.
  • CCR1072-1G-8S+ - All SFP+ interfaces can be used in 1G mode if required.
  • CCR1036-8G-2S+ - All SFP+ interfaces can be used in 1G mode if required.
  • CCR1009-8G-1S-1S+ - All SFP+ interfaces can be used in 1G mode if required.
  • CCR1009-7G-1C-1S+ - All SFP+ interfaces can be used in 1G mode if required.
  • CSS326-24G-2S+RM - All SFP+ interfaces can be used in 1G mode if required.
  • CRS3xx series switches - All SFP+ interfaces can be used in 1G mode if required.
  • RB5009 series - SFP+1 interface can be used in 1G mode if required.
  • RB4011 series - SFP+1 interface can be used in 1G mode if required.
  • CRS226-24G-2S+ - Only SFP+1 supports 1G link speed, SFP+2 is for 10G links only.
  • CRS210-8G-2S+ - Only SFP+1 supports 1G link speed, SFP+2 is for 10G links only.
  • CSS610 series switches - All SFP+ interfaces can be used in 1G mode if required.

Devices which SFP+ interfaces can be used only for 10G links:

  • CCR1016-12S-1S+
  • CRS212-1G-10S-1S+

SFP+ interface compatibility with 10G/25G optical transceivers

MikroTik devices with SFP+ ports can establish 10G links using 10G/25G optical fiber transceivers, however additional SFP Rate Select setting must be configured to avoid data corruption during transmission. The SFP Rate Select setting is implemented since RouterOS v6.49 and the following settings are required on the SFP+ interface: 

/interface ethernet set sfp-sfpplus1 auto-negotiation=no speed=10Gbps full-duplex=yes sfp-rate-select=low

This requirement applies to MikroTik 10G/25G modules:

  • XS+31LC10D
  • XS+2733LC15D

SFP+/SFP28 interface compatibility with 2.5G transceivers

The 2.5G link rate support is implemented since RouterOS v7.3. MikroTik devices with SFP+ and SFP28 interfaces that support 2.5G link rate require following settings to be set on both linked device interfaces. 

/interface ethernet set sfp-sfpplus1 auto-negotiation=no speed=2.5Gbps full-duplex=yes
  • auto-negotiation disabled
  • port speed 2.5G
  • full-duplex

Devices which support 2.5G links in SFP+/SFP28 ports:

  • CRS3xx series switches - All SFP+ interfaces can be used in 2.5G mode if required.
  • CCR2004-1G-12S+2XS - All SFP+ and SFP28 interfaces can be used in 2.5G mode if required.
  • CCR2116-12G-4S+ - All SFP+ interfaces can be used in 2.5G mode if required.
  • CRS518-16XS-2XQ - All SFP28 interfaces can be used in 2.5G mode if required.
  • CCR2216-1G-12XS-2XQ - All SFP28 interfaces can be used in 2.5G mode if required.
  • RB5009 series - SFP+ interface can be used in 2.5G mode if required.

QSFP+/QSFP28 interface supported link rates

QSFP+ interfaces of MikroTik CRS3xx series devices support following link speeds.

  • 1x 40G
  • 4x 10G
  • 4x 1G

40G links can be established either with autonegotiation or forced 40G speed.
4x 10G and 4x 1G links can be established only with forced speeds and disabled autonegotiation.
In a single link mode only the first QSFP+ subinterface needs to be configured.

Example of forced 1x 40G speed with disabled autonegotiation: 

/interface ethernet set qsfpplus1-1 auto-negotiation=no speed=40Gbps full-duplex=yes

In four link mode all four QSFP28 subinterfaces support configuration of different speeds.

Example of forced 4x 10G speed with disabled autonegotiation: 

/interface ethernet set qsfpplus1-1 auto-negotiation=no speed=10Gbps full-duplex=yes
/interface ethernet set qsfpplus1-2 auto-negotiation=no speed=10Gbps full-duplex=yes
/interface ethernet set qsfpplus1-3 auto-negotiation=no speed=10Gbps full-duplex=yes
/interface ethernet set qsfpplus1-4 auto-negotiation=no speed=10Gbps full-duplex=yes


QSFP28 interfaces of MikroTik CRS5xx series and CCR2216 devices support following link speeds.

  • 1x 100G
  • 1x 40G
  • 4x 25G
  • 4x 10G
  • 4x 1G

Not supported: 2x 50G; 1x 50G; 2x 40G

100G links can be established either with autonegotiation or forced 100G speed.
1x 40G, 4x 25G, 4x 10G and 4x 1G links can be established only with forced speeds and disabled autonegotiation.
In a single link mode only the first QSFP28 subinterface needs to be configured.

Example of forced 1x 40G speed with disabled autonegotiation: 

/interface ethernet set qsfp28-1-1 auto-negotiation=no speed=40Gbps full-duplex=yes

In four link mode all four QSFP28 subinterfaces support configuration of different speeds.

Example of forced 4x 25G speed with disabled autonegotiation: 

/interface ethernet set qsfp28-1-1 auto-negotiation=no speed=25Gbps full-duplex=yes
/interface ethernet set qsfp28-1-2 auto-negotiation=no speed=25Gbps full-duplex=yes
/interface ethernet set qsfp28-1-3 auto-negotiation=no speed=25Gbps full-duplex=yes
/interface ethernet set qsfp28-1-4 auto-negotiation=no speed=25Gbps full-duplex=yes

QSFP+ interface compatibility with QSFP+ to SFP+ breakout cables

MikroTik devices can establish links between QSFP+ and SFP+ ports using breakout cable when following settings are configured on the QSFP+ interface: 

/interface ethernet set qsfpplus1-1 auto-negotiation=no speed=10Gbps full-duplex=yes
/interface ethernet set qsfpplus1-2 auto-negotiation=no speed=10Gbps full-duplex=yes
/interface ethernet set qsfpplus1-3 auto-negotiation=no speed=10Gbps full-duplex=yes
/interface ethernet set qsfpplus1-4 auto-negotiation=no speed=10Gbps full-duplex=yes
  • auto-negotiation disabled
  • port speed 10G
  • full-duplex

Note: On the SFP+ side, auto-negotiation remains enabled.


Retrieved from "https://wiki.mikrotik.com/index.php?title=MikroTik_wired_interface_compatibility&oldid=34602"