Manual:System/LEDS

Applies to RouterOS: v5 +

Summary

RouterOS allows to configure each leds activity the way that user wishes. It is possible to configure the leds to display wireless strength, blink the leds on interface traffic activity and many other options.

For example default led configuration on Groove

[admin@MikroTik] /system leds> print 
Flags: X - disabled 
 #   TYPE                     INTERFACE                   LEDS                 
 0   wireless-signal-strength                             led1                 
                                                          led2                 
                                                          led3                 
                                                          led4                 
                                                          led5                 
 1   interface-activity       ether1                      user-led     

RB Groove uses five leds for wireless strength and one for ethernet activity monitoring.

Leds

Sub-menu: /system leds

Property	Description
disabled (yes | no; Default: no)	Whether item is disabled
interface (string; Default: )	Name of the interface which will be used for led status. Applicable only if type is interface specific.
modem-signal-treshold (integer [-113..-51]; Default: )	Applicable if type is modem-signal
leds (list of leds; Default: )	List of led names used for status report. For example wireless signal strength will require more than one led.
type (ap-cap| flash-access | interface-activity | interface-receive | interface-speed | interface-status | interface-transmit | modem-signal | off | on | poe-out | wireless-signal-strength | wireless-status; Default: )	Type of the status: ap-cap - blink on CAP initialising with CAPsMAN, steady on once connected flash-access - blink the led on flash access interface-activity - blink the led on interface (traffic) activity interface-receive - blink the led on interface received traffic interface-speed - light the led when interface works in 10Gbit rate interface-status - light the led on interface status change interface-transmit - blink the led on interface transmitted traffic modem-signal - blink the led on 3G modem signal (eiher USB or miniPCIe) off - turn off the led on - turn on the led poe-out - light the led when interface PoE out turns on wireless-signal-strength - light the leds displaying wireless signal (requires more than one led) wireless-status - light the led on wireless status change.

Leds Setting

Global settings are stored in Leds Setting menu. Currently "RB cAP 2n" and "RB cAP 2nD" support turning off all leds (LED dark mode).

Sub-menu: /system leds setting

Property	Description
all-leds-off (after-1h | after-1min | immediate | never; Default: never)	Whether and when all leds of router can be turned off

Basic example

Led control via CLI commands for scripting purposes:

• prior to v6.23 and older releases:

#turn led on
:led led1=yes
#turn led off
:led led1=no

• v6.23 and newer releases:

#add led entry with specific type "on" or "off" to leds menu
/system leds add leds=led1 type=off
#to control led
/system leds set [find where leds="led1"] type=on
or
/system leds set [find where leds="led1"] type=off

Enable the User ACT LED to show current CAP status on a RB951

/system leds
add leds=user-led type=ap-cap

Modem Signal Strength example

The whole modem-signal strength range is [-113..-51] and the modem-signal-threshold increases the weakest signal limit to -91 so the signal range for LED indication is [-91..-51]. That range is divided into equal parts depending on number of LEDs configured for modem-signal LED trigger. The first LED turns on when signal is above -91 and the last LED turns on when signal reaches -51.

/system leds
add interface=lte1 leds=led1,led2,led3,led4,led5 modem-signal-treshold=-91 type=modem-signal

[ Top | Back to Content ]