MikroTik SFP module compatibility table

From MikroTik Wiki
Revision as of 08:11, 13 August 2019 by Vjaceslavsa (talk | contribs)
Jump to navigation Jump to search

This document clarifies compatibility between MikroTik made SFP modules and MikroTik RouterBOARD hardware

Model S-RJ01 S+RJ10 S-85DLC05D S-31DLC20D S-3553LC20D S-55DLC80D S-4554LC80D S+85DLC03D S+31DLC10D S+2332LC10D SFP CWDM SFP+ 1m/3m DAC S+AO0005
CCR1072-1G-8S+ + + + + + + + + + + + + +
CCR1036-12G-4S + - + + + + + + + + + + +
CCR1036-8G-2S+ + + + + + + + + + + + + +
CCR1016-12S-1S+ + 1 + + 1 + 1 + 1 + 1 + 1 + + + + + +
CCR1009-7G-1C + - + + + + + + + + + + +
CCR1009-8G-1S-1S+ + + + + + + + + + + + + +
CCR1009-7G-1C-1S+ + + + + + + + + + + + + +
CRS125-24G-1S + - + + + + + + + + + + +
CSS/CRS305-1G-4S+ + + + + + + + + + + + + +
CSS/CRS309-1G-8S+ + + 5 + + + + + + + + + + +
CRS312-4C+8XG - + + + + + + + + + + + +
CRS326-24S+2Q+ + + + + + + + + + + + + +
CSS/CRS326-24G-2S+ + + + + + + + + + + + + +
CSS/CRS317-1G-16S+ + + 3 + + + + + + + + + + +
CSS/CRS328-4C-20S-4S+ + + + + + + + + + + + + +
CSS/CRS328-24P-4S+ + + + + + + + + + + + + +
CRS226-24G-2S+ - + + 2 + 2 + 2 + 2 + 2 + + + + + +
CRS212-1G-10S-1S+ + 1 + + 1 + 1 + 1 + 1 + 1 + + + + + +
CRS210-8G-2S+ - + + 2 + 2 + 2 + 2 + 2 + + + + + +
CRS112-8G-4S/8P-4S + - + + + + + + + + + + +
CRS109-8G-1S + - + + + + + + + + + + +
CRS106-1C-5S/FiberBox + - + + + + + + + + + + +
RB4011 + + + + + + + + + + + - 4 + 4
RB3011 + - + + + + + + + + + + +
RB2011 + - + + + + + + + + + + +
RB260 + - + + + + + + + + + + +
RB922/921 + - + + + + + + + + + + +
RB953GS + - + + + + + + + + + + +
hAP AC + - + + + + + + + + + + +
hEX PoE/PowerBox Pro + - + + + + + + + + + + +
hEX S + - + + + + + + + + + + +
FTC + - + + + + + + + + + + +
Legend
Color codes: Not supported Check notes below


NOTES:

  1. CCR1016-12S-1S+ / CRS212-1G-10S-1S+ -- SFP+1 interface does not work on any other link speed than 10G (does not support 1.25G fiber optic transceivers)
  2. CRS226 / CRS210 -- Only SFP+1 interface supports SFP 1.25G fiber optic transceivers, SFP+2 works only with 10G transceivers/links.
  3. CSS/CRS317-1G-16S+ -- power controller supports up to 10 simultaneous S+RJ10 modules.
  4. RB4011 -- Only active Direct Attach Cables (MikroTik S+AO0005) are supported. Passive DAC (MikroTik S+DA0001/S+DA0003) are not supported.
  5. CSS/CRS309-1G-8S+ -- 8x S+RJ10 are supported if PoE-in Voltage >30V. Up 4x S+RJ10 are supported when PoE-in Voltage = 24V.


Warning: Proper support for S-RJ01 modules on CCR1072-1G-8S+ is enabled only staring with v6.34rc software builds.


S-RJ01

Table that states in what link rates if mounted in specific MikroTik devices S-RJ01 module will be able to work. Use these modules only with auto-negotiation enabled, forced link speeds are not supported. They will negotiate to correct duplex and highest possible rate.

Model 1000 100 10
RB4011 + + +
RB3011 + + +
RB922 + + +
RB921 + + +
hAP ac + + +
hEX PoE + + +
RB953 +/+ +/- +/-
RB2011 + - -
RB260 + - -
FTC + - -
CRS106 + + +
CRS112 + + +
CRS125/CRS109 + + +
CRS212 + + +
CRS226/CRS210 - - -
CSS/CRS305-1G-4S+ + + +
CSS/CRS309-1G-8S+ + + +
CSS/CRS326-24G-2S+ + + +
CSS/CRS328-4C-20S-4S+ + + +
CSS/CRS328-24P-4S+ + + +
CSS/CRS317-1G-16S+ + + +
CCR1009 +/+ +/+ +/+
CCR1016-12S-1S+ + + +
CCR1036-12G-4S + + +
CCR1036-8G-2S+ + + +
CCR1072-1G-8S+ + + +

Notes:

  • Rate works fine: +
  • Rate does not work: -
  • RB953: SFP2/SFP1
  • CCR1009: SFP+/SFP

10 Gigabit Ethernet

S+RJ10

Use these modules only in 10G SFP+ ports with auto-negotiation enabled, forced link speeds are not supported. They will negotiate to correct duplex and highest possible rate. Be aware of S+RJ10 General Guidance.

Speed Cable type S+RJ10 to other brand S+RJ10 to S+RJ10
10BASE-T Cat5e/6 100m 100m
100BASE-T Cat5e/6 100m 100m
1000BASE-T Cat5e/6 100m 200m
2.5GBASE-T Cat5e/6 UTP 100m 170m
2.5GBASE-T Cat5e/6 STP 100m 200m
5GBASE-T Cat5e/6 100m 100m
10GBASE-T Cat6/7 30m 30m

Note: Negotiated speed highly depends on quality and length of the cables that are used.


The new revision of S+RJ10 now supports jumbo frames up to 10218 bytes at link speed 2.5Gbps, 5Gbps and 10Gbps.

Link Speed Max MTU
10Gbps 10218
5Gbps 10218
2.5Gbps 10218
1000Mbps 1504
100Mbps 1504
10Mbps 1504

CRS312-4C+8XG

10GE ports maximum supported cable length.

Speed Cable type 10 Gigabit Ethernet ports
10BASE-T Cat5e/6 100m
100BASE-T Cat5e/6 100m
1000BASE-T Cat5e/6 100m
2.5GBASE-T Cat5e/6 100m
5GBASE-T Cat5e/6 100m
10GBASE-T Cat6/7 30m

Note: Negotiated speed highly depends on quality and length of the cables that are used.


Warning: 10GE ports doesn't support Half duplex mode with forced link speeds.


SFP+ interface compatibility settings with SFP optical transceivers

For MikroTik devices with SFP+ interface that support both 10G and 1G link rate following settings are needed to be set on both linked devices for required interfaces. These settings only relate when optical SFP transceivers are used. In order to get them working in 1G link rate, use the following configuration:

  • auto-negotiation disabled
  • port speed 1G
  • FD

Devices which SFP+ ports support 1G links:

  • CCR1072-1G-8S+ - All SFP+ interfaces can be used in 1G mode if required.
  • CCR1036-8G-2S+ - All SFP+ interfaces can be used in 1G mode if required.
  • CCR1009-8G-1S-1S+ - All SFP+ interfaces can be used in 1G mode if required.
  • CCR1009-7G-1C-1S+ - All SFP+ interfaces can be used in 1G mode if required.
  • CSS326-24G-2S+RM - All SFP+ interfaces can be used in 1G mode if required.
  • CRS3xx series switches - All SFP+ interfaces can be used in 1G mode if required.
  • RB4011 series - SFP+1 interface can be used in 1G mode if required.
  • CRS226-24G-2S+ - Only SFP+1 supports 1G link speed, SFP+2 is for 10G links only.
  • CRS210-8G-2S+ - Only SFP+1 supports 1G link speed, SFP+2 is for 10G links only.

Devices which SFP+ interfaces can be used only for 10G links:

  • CCR1016-12S-1S+
  • CRS212-1G-10S-1S+

SFP interface compatibility with 100M fiber links

Combo interface SFP part on below mentioned devices is compatible with fast ethernet fiber links.

Compatible devices:

  • CCR1009-7G-1C (combo1-sfp)
  • CCR1009-7G-1C-1S+ (combo1-sfp)
  • CRS106-1C-5S (combo1-sfp)
  • CRS328-4C-20S-4S+ (combo1-sfp; combo2-sfp; combo3-sfp; combo4-sfp)

QSFP+ interfaces compatibility settings with SFP+ ports

For MikroTik devices, the connection between the QSFP+ and SFP+ ports, using breakout cables, the following settings on QSFP+ interfaces need to be set:

  • auto-negotiation disabled
  • port speed 10G
  • FD

Note: On the SFP+ side, auto-negotiation remains enabled.


Retrieved from "https://wiki.mikrotik.com/index.php?title=MikroTik_SFP_module_compatibility_table&oldid=33539"