RouterBOOT changelog
What's new in 2.27:
- memory fix for RB800/RB1000/RB1100;
- fixed pin-hole reset on RB750G;
What's new in 2.26:
- added RB816 support on RB600;
- fixed router hangup during etherboot if blasted with lots of packets;
- added silent boot;
- fixed Flashfig;
What's new in 2.25:
- new feature - Flashfig;
- fixed etherboot on RB493;
- fixed occasional lockup of kernel image loading on RB400 series;
- added disable UART feature;
What's new in 2.24:
- added support for RB816;
What's new in 2.23:
- added support for RB750G;
- added support for RB800;
What's new in 2.22:
- fixed support for RB750;
What's new in 2.21:
- added support for RB750;
What's new in 2.20:
- added support for RB450G;
What's new in 2.19:
- fixed support for MLC NAND chip;
- fixed memory issue on RB600;
What's new in 2.18:
- fixed via-rhine disappearing on RB532 and RB564;
- added support for RB493AH;
What's new in 2.17:
- added support for MLC NAND chip;
What's new in 2.16:
- fixed bug - boot from NAND on RB532A could fail (bug introduced in 2.13);
- fixed bug - etherboot on RB433/RB450 at 10Mbit did not work;
What's new in 2.15:
- fixed RB333 overheating problem;
- added support for microSD card on RB433;
What's new in 2.14:
- fixed nand boot on RB150 (broken in v2.13);
What's new in 2.13:
- improved memtest;
- fixed RB600 memory issue;
What's new in 2.12:
- nand improvement for RB532A;
What's new in 2.11:
- fixed bug - in one rare case boot from NAND could fail with "data is corrupted" message while data is correctable in reality;
What's new in 2.10:
- 100ms delay before PCI bus are initialized;
What's new in 2.9:
- added support for RB192;
What's new in 2.8:
- fixed CompactFlash resetting router config on RB153 (broken in v2.7);
What's new in 2.7:
- fixed bug - RouterOS command "/system reset-configuration"
was not resetting RB532 VIA ethernet mac address to default;
- added support for RB532r5;
What's new in 2.6:
- fixed CompactFlash reseting router config on RB153;
What's new in 2.4:
- fixed etherboot on RB100 to work reliably;
What's new in 2.2:
- fixed repeated initrd image loading;
What's new in 2.1:
- fixed crash during memory test within RouterBOOT;
What's new in 2.0:
- added support for RB153;
What's new in 1.13:
- fixed nand format feature to mark back really bad blocks as bad;
What's new in 1.12:
- reset-jumper resets bios settings to defaults;
What's new in 1.11:
- fixed reboot failure on RB500 with new RAM modules;
What's new in 1.10:
- added workaround for reboot failure on RB500 with new RAM modules;
What's new in 1.9:
- new boot option - "boot NAND, if fail then Ethernet";
What's new in 1.8:
- fixed bug - it was possible for RB500 booter to stop working completely;
What's new in 1.7:
- added nand format feature;
What's new in 1.3:
- added support for large block NAND devices;
What's new in 1.2:
- fixed bios entering on <delete> key for hyperterminal;
- routerboard 100 beep before jumping to kernel code;
- added nand READY/BUSY checking for rb100;
- improved speed for memory test;