Manual:Fast Path

Applies to RouterOS: v6.0rc2 +

Summary

Fast path allows to forward packets without additional processing in the Linux kernel. It improves forwarding speeds significantly.

For fast path to work, interface support and specific configuration conditions are required.

List of devices with FastPath support

Interface FastPath support can be checked by doing "/interface print detail" and seeing fast-path property value.

RouterBoard	Interfaces
RB6xx series	ether1,2
RB7xx series	all ethernets
RB8xx series	ether1,2
RB9xx series	all ethernets
RB1000	all ethernets
RB1100 series	ether1-10,11
RB2011 series	all ethernets and sfp
CCR series routers	all ethernets and sfps
All devices	wireless interfaces, if wireless-fp or wireless-cm2 package used
	bridge interfaces (since 6.29)

FastPath Handlers

Currently RouterOS has following fast path handlers:

• ipv4
• ipv4 fasttrack
• traffic generator
• mpls
• bridge

Note: Packet can be forwarded by fast path handler only if at least source interface support fast path. For complete fast path forwarding destination interface support is also required. See the list of supported interfaces.

IPv4 handler

IPv4 fast path is automatically used if following conditions are met:

• firewal rules are not configured;
• Traffic flow is disabled /ip traffic-flow enabled=no;
• Simple and queue trees with parent=global are not configured;
• no mesh, metarouter interface configuration;
• sniffer, torch and traffic generator is not running;
• connection tracking is not active;
• ip accounting is disabled (/ip accounting enabled=no);
• VRFs are not set (/ip route vrf is empty);
• Hotspot is not used (/ip hostspot has no interfaces);
• IpSec policies are not configured (ROS v6.8);
• no active mac-ping, mac-telnet or mac-winbox sessions;
• /tool mac-scan is not actively used;
• /tool ip-scan is not actively used;
• /tool wol is not actively used;
• /interface mesh traceroute is not actively used;

/ip firewall connection tracking set enabled parameter has new auto value Which means that connection tracking is disabled by default until firewall rules are added.

IPv4 FastTrack handler

IPv4 FastTrack handler is automatically used for marked connections. Use firewall action "fasttrack-connection" to mark connections for fasttrack.

Currently only TCP and UDP connections can be actually fasttracked (even though any connection can be marked for fasttrack).

IPv4 FastTrack handler supports NAT (SNAT, DNAT or both).

Note that not all packets in a connection can be fasttracked, so it is likely to see some packets going through slow path even though connection is marked for fasttrack.

Note that fasttracked packets bypass firewall, simple queues, queue tree with parent=global, ip traffic-flow, ip accounting, ipsec, hotspot universal client, vrf assignment, so it is up to administrator to make sure fasttrack does not interfere with other configuration;

IPv4 FastTrack is active if following conditions are met:

• no mesh, metarouter interface configuration;
• sniffer, torch and traffic generator is not running;
• no active mac-ping, mac-telnet or mac-winbox sessions;
• /tool mac-scan is not actively used;
• /tool ip-scan is not actively used;
• /tool wol is not actively used;
• /interface mesh traceroute is not actively used;

Traffic Generator handler

Traffic Generator fast path is automatically used for interfaces that support this feature.

MPLS handler

MPLS fast path is automatically used for interfaces that support this feature.

Currently MPLS fast-path applies only to MPLS switched traffic (frames that enter router as MPLS and must leave router as MPLS) - MPLS ingress and egress (including VPLS tunnel endpoints that do VPLS encap/decap) will operate as before.

Bridge handler

Bridge fast path is automatically used if following conditions are met:

• no bridge firewall rules (/interface bridge filter, /interface bridge nat) are configured,
• /interface bridge settings use-ip-firwall=no,
• destination interface queue is set to only-hw-queue,
• no mesh, metarouter interface configuration,
• sniffer, torch and traffic generator is not running,
• if wireless is configured, then wireless-fp or wireless-cm2 package must be used in order to use FastPath

Note: Currently VLAN, PPP and Bonding interfaces does not support FastPath

Note: Starting from v6.1 added VRRP interface no longer disables fast path globally. Ipv4 and bridge fast path handlers will not work only if source interface is vrrp slave interface.

[ Top | Back to Content ]