Manual:CRS3xx series switches

Applies to RouterOS: v6.41 +

Summary

The Cloud Router Switch series are highly integrated switches with high performance ARM CPU and feature-rich packet processor. The CRS switches can be designed into various Ethernet applications including unmanaged switch, Layer 2 managed switch, carrier switch and wired unified packet processing.

Warning: This article applies to CRS3xx series switches and not to CRS1xx/CRS2xx series switches.

Features	Description
Forwarding	Configurable ports for switching or routing Full non-blocking wirespeed switching Up to 16k MAC entries in Unicast FDB for Layer 2 unicast forwarding Up to 1k MAC entries in Multicast FDB for multicast forwarding Up to 256 MAC entries in Reserved FDB for control and management purposes All Forwarding Databases support IVL and SVL Configurable Port based MAC learning limit Jumbo frame support
Mirroring	Various types of mirroring: Port based mirroring VLAN based mirroring MAC based mirroring 2 independent mirroring analyzer ports
VLAN	Fully compatible with IEEE802.1Q and IEEE802.1ad VLAN 4k active VLANs Flexible VLAN assignment: Port based VLAN VLAN filtering

This table clarifies main differences between Cloud Router Switch models.

Model	Switch Chip	CPU	Wireless	SFP+ port	Access Control List	Jumbo Frame (Bytes)
CRS326-24G-2S+	Marvell-98DX3236	400MHz	-	+	+	10218
CRS317-1G-16S+	Marvell-98DX8216	800MHz	-	+	+	10218

Port Switching

Since v6.40rc29 on CRS3xx series switches bridges will handle all Layer2 forwarding and the use of switch chip (hw-offload) will automatically turn on if appropriate conditions are met. The rest of RouterOS Switch features remain untouched in usual menus. By default all newly created bridge ports have hw=yes option and it allows enabling of hw-offload when possible. If such functionality is not required, it can be disabled by hw=no on bridge port to have completely software operated bridging.

Note: Downgrading to previous RouterOS versions will not restore master-port configuration. The bridge with no hw-offload will appear instead and master-port configuration will have to be redone from the beginning.

• Port switching with bridge configuration and enabled hw-offload since v6.40rc29

[admin@MikroTik] > interface bridge export 
/interface bridge
add name=bridge1 igmp-snooping=no  protocol-mode=none
/interface bridge port
add bridge=bridge1 interface=ether2
add bridge=bridge1 interface=ether3
add bridge=bridge1 interface=ether4
add bridge=bridge1 interface=ether5
[admin@MikroTik] > 

[admin@MikroTik] > interface bridge port print 
Flags: X - disabled, I - inactive, D - dynamic, H - hw-offload 
 #     INTERFACE              BRIDGE              HW  PVID PRIORITY  PATH-COST INTERNAL-PATH-COST    HORIZON
 0   H ether2                 bridge1             yes    1     0x80         10                 10       none
 1   H ether3                 bridge1             yes    1     0x80         10                 10       none
 2   H ether4                 bridge1             yes    1     0x80         10                 10       none
 3   H ether5                 bridge1             yes    1     0x80         10                 10       none
[admin@MikroTik] > 

Following list states what features currently in 6.41rc will enable hardware offloading on CRS3xx series switches:

• Features in Switch menu
• Bridge STP/RSTP
• Bridge MSTP
• Bridge IGMP Snooping
• Bridge VLAN Filtering

Following list states what features currently in 6.41rc will disable hardware offloading on CRS3xx series switches:

• bonding

See also

• CRS examples
• CRS features
• Switch Chip Features
• MTU on RouterBOARD

[ Top | Back to Content ]