IKEv2 EAP between NordVPN and RouterOS: Difference between revisions

From MikroTik Wiki
Jump to navigation Jump to search
mNo edit summary
mNo edit summary
 
Line 73: Line 73:
</pre>
</pre>


==Choosing what traffic to send over the tunnel==
==Choosing what to send over the tunnel==


If we look at the generated dynamic [[M:IP/IPsec#Policies | policies]], we see that only traffic with a specific (received by [[M:IP/IPsec#Mode_configs | mode config]]) source address will be sent through the tunnel. But a router in most cases will need to route a specific device or network through the tunnel. In such case we can use source NAT to change the source address of packets to match the mode config address. Since the mode config address is dynamic, it is impossible to create static source NAT rule. In RouterOS it is possible to generate dynamic source NAT rules for mode config clients.
If we look at the generated dynamic [[M:IP/IPsec#Policies | policies]], we see that only traffic with a specific (received by [[M:IP/IPsec#Mode_configs | mode config]]) source address will be sent through the tunnel. But a router in most cases will need to route a specific device or network through the tunnel. In such case we can use source NAT to change the source address of packets to match the mode config address. Since the mode config address is dynamic, it is impossible to create static source NAT rule. In RouterOS it is possible to generate dynamic source NAT rules for mode config clients.
Line 124: Line 124:
</pre>
</pre>


When it is done, a dynamic NAT rule is generated with the dynamic address provided by the server:
When it is done, a NAT rule is generated with the dynamic address provided by the server:


<pre>
<pre>
Line 133: Line 133:
</pre>
</pre>


After that, it is possible to apply this <var>connection-mark</var> to any traffic using [[M:IP/Firewall/Mangle | Mangle firewall]]. In this example, access to mikrotik.com is granted over the tunnel.
After that, it is possible to apply this <var>connection-mark</var> to any traffic using [[M:IP/Firewall/Mangle | Mangle firewall]]. In this example, access to mikrotik.com and 8.8.8.8 is granted over the tunnel.


Create a new address list:
Create a new address list:
Line 140: Line 140:
/ip firewall address-list
/ip firewall address-list
add address=mikrotik.com list=VPN
add address=mikrotik.com list=VPN
add address=8.8.8.8 list=VPN
</pre>
</pre>


Apply <var>connection-mark</var> to traffic going to the created address list:
Apply <var>connection-mark</var> to traffic matching the created address list:


<pre>
<pre>

Latest revision as of 06:30, 16 July 2019

Version.png

Applies to RouterOS: v6.45.2 +

Starting from RouterOS v6.45, it is possible to establish IKEv2 secured tunnel to NordVPN servers using EAP authentication. This manual page explains how to configure it.

Ikev2-rw-nordvpn.png

Installing the root CA

Start off by downloading and importing the NordVPN root CA certificate.

/tool fetch url="https://downloads.nordvpn.com/certificates/root.der"
/certificate import file-name=root.der

There should now be the trusted NordVPN Root CA certificate in System/Certificates menu.

[admin@MikroTik] > /certificate print where name~"root.der"
Flags: K - private-key, L - crl, C - smart-card-key, A - authority, I - issued, R - revoked, E - expired, T - trusted 
 #         NAME            COMMON-NAME            SUBJECT-ALT-NAME                                         FINGERPRINT           
 0       T root.der_0      NordVPN Root CA                                                                 8b5a495db498a6c2c8c...

Finding out the server's hostname

Navigate to https://nordvpn.com/servers/tools/ and find out the recommended server's hostname. In this case it is lv20.nordvpn.com.

Nordvpn hostname.png

Setting up the IPsec tunnel

It is advised to create a separate Phase 1 profile and Phase 2 proposal configurations to not interfere with any existing or future IPsec configuration.

/ip ipsec profile
add name=NordVPN
/ip ipsec proposal
add name=NordVPN pfs-group=none

While it is possible to use the default policy template for policy generation, it is better to create a new policy group and template to separate this configuration from any other IPsec configuration.

/ip ipsec policy group
add name=NordVPN
/ip ipsec policy
add dst-address=0.0.0.0/0 group=NordVPN proposal=NordVPN src-address=0.0.0.0/0 template=yes

Create a new mode config entry with responder=no that will request configuration parameters from the server.

/ip ipsec mode-config
add name=NordVPN responder=no

Lastly, create peer and identity configurations. Specify your NordVPN credentials in username and password parameters.

/ip ipsec peer
add address=lv20.nordvpn.com exchange-mode=ike2 name=NordVPN profile=NordVPN
/ip ipsec identity
add auth-method=eap certificate="" eap-methods=eap-mschapv2 generate-policy=port-strict mode-config=NordVPN peer=NordVPN policy-template-group=NordVPN username=support@mikrotik.com password=secret

Verify that the connection is successfully established.

/ip ipsec
active-peers print
installed-sa print

Choosing what to send over the tunnel

If we look at the generated dynamic policies, we see that only traffic with a specific (received by mode config) source address will be sent through the tunnel. But a router in most cases will need to route a specific device or network through the tunnel. In such case we can use source NAT to change the source address of packets to match the mode config address. Since the mode config address is dynamic, it is impossible to create static source NAT rule. In RouterOS it is possible to generate dynamic source NAT rules for mode config clients.

Option 1: Sending all traffic over the tunnel

In this example, we have a local network 10.5.8.0/24 behind the router and we want all traffic from this network to be sent over the tunnel. First of all, we have to make a new IP/Firewall/Address list which consists of our local network.

/ip firewall address-list
add address=10.5.8.0/24 list=local

It is also possible to specify only single hosts from which all traffic will be sent over the tunnel. Example:

/ip firewall address-list
add address=10.5.8.120 list=local
add address=10.5.8.23 list=local

When it is done, we can assign newly created IP/Firewall/Address list to mode config configuration.

/ip ipsec mode-config
set [ find name=NordVPN ] src-address-list=local

Verify correct source NAT rule is dynamically generated when the tunnel is established.

[admin@MikroTik] > /ip firewall nat print 
Flags: X - disabled, I - invalid, D - dynamic 
 0  D ;;; ipsec mode-config
      chain=srcnat action=src-nat to-addresses=192.168.77.254 src-address-list=local dst-address-list=!local
Icon-warn.png

Warning: Make sure dynamic mode config address is not a part of local network.


Icon-note.png

Note: It is also possible to combine both options (1 and 2) to allow access to specific addresses only for specific local addresses/networks


Option 2: Accessing certain addresses over the tunnel

It is also possible to send only specific traffic over the tunnel by using the connection-mark parameter in Mangle firewall. It works similarly as Option 1 - a dynamic NAT rule is generated based on configured connection-mark parameter under mode config.

First of all, set the connection-mark under your mode config configuration.

/ip ipsec mode-config
set [ find name=NordVPN ] connection-mark=NordVPN

When it is done, a NAT rule is generated with the dynamic address provided by the server:

[admin@MikroTik] > /ip firewall nat print 
Flags: X - disabled, I - invalid, D - dynamic 
 0  D ;;; ipsec mode-config
      chain=srcnat action=src-nat to-addresses=192.168.77.254 connection-mark=NordVPN 

After that, it is possible to apply this connection-mark to any traffic using Mangle firewall. In this example, access to mikrotik.com and 8.8.8.8 is granted over the tunnel.

Create a new address list:

/ip firewall address-list
add address=mikrotik.com list=VPN
add address=8.8.8.8 list=VPN

Apply connection-mark to traffic matching the created address list:

/ip firewall mangle
add action=mark-connection chain=prerouting dst-address-list=VPN new-connection-mark=NordVPN passthrough=yes
Icon-note.png

Note: It is also possible to combine both options (1 and 2) to allow access to specific addresses only for specific local addresses/networks


[ Top | Back to Content ]