Manual:CRS1xx/2xx series switches

Applies to RouterOS: v6.8 +

Summary

The Cloud Router Switch series are highly integrated switches with high performance MIPS CPU and feature-rich packet processor. The CRS switches can be designed into various Ethernet applications including unmanaged switch, Layer 2 managed switch, carrier switch and wireless/wired unified packet processing.

Abbreviations and Explanations

CVID - Customer VLAN id: inner VLAN tag id of the IEEE 802.1ad frame

SVID - Service VLAN id: outer VLAN tag id of the IEEE 802.1ad frame

IVL - Independent VLAN learning - learning/lookup is based on both MAC addresses and VLAN IDs.

SVL - Shared VLAN learning - learning/lookup is based on MAC addresses - not on VLAN IDs.

TPID - Tag Protocol Identifier

PCP - Priority Code Point: a 3-bit field which refers to the IEEE 802.1p priority

DEI - Drop Eligible Indicator

DSCP - Differentiated services Code Point

Drop precedence - internal CRS switch QoS attribute used for packet enqueuing or dropping.

Generic Configuration

Sub-menu: /interface ethernet switch

CRS switch chip is configurable from the /interface ethernet switch console menu.

Property	Description
bridge-type (customer-vlan-bridge | service-vlan-bridge; Default: service-vlan-bridge)	Bridge type defines which VLAN tag is used as Lookup-VID. Lookup-VID serves as the VLAN key for all VLAN-based lookup.
bypass-l2-security-check-filter-for (protocols; Default: none)	Protocols which are excluded from Policy rule security check. (arp, dhcpv4, dhcpv6, eapol, igmp, mld, nd, pppoe-discovery, ripv1)
bypass-vlan-ingress-filter-for (protocols; Default: none)	Protocols which are excluded from Ingress VLAN filtering. These protocols are not dropped if they have invalid VLAN. (arp, dhcpv4, dhcpv6, eapol, igmp, mld, nd, pppoe-discovery, ripv1)
drop-if-invalid-or-src-port- -not-member-of-vlan-on-ports (ports; Default: none)	Ports which drop invalid and other port VLAN id frames.
drop-if-no-vlan-assignment-on-ports (ports; Default: none)	Ports which drop frames if no VLAN assignment is applied.
egress-mirror-ratio (1/32768..1/1; Default: 1/1)	Proportion of egress mirrored packets compared to all packets.
egress-mirror0-enable (yes | no; Default: yes)	Enables or disables egress mirroring on Mirror0 port.
egress-mirror0-format (analyzer-configured | modified | original; Default: modified)	analyzer-configured - The packet is same as the packet to destination. VLAN format is modified based on the VLAN configurations of the analyzer port. modified - The packet is same as the packet to destination. VLAN format is modified based on the VLAN configurations of the egress port. original - Traffic is mirrored without any change to the original incoming packet format. But service VLAN tag is stripped in edge port.
egress-mirror0-port (port; Default: switch1-cpu)	The first egress mirroring analyzer port.
egress-mirror1-enable (yes | no; Default: yes)	Enables or disables egress mirroring on Mirror1 port.
egress-mirror1-format (analyzer-configured | modified | original; Default: modified)	analyzer-configured - The packet is same as the packet to destination. VLAN format is modified based on the VLAN configurations of the analyzer port. modified - The packet is same as the packet to destination. VLAN format is modified based on the VLAN configurations of the egress port. original - Traffic is mirrored without any change to the original incoming packet format. But service VLAN tag is stripped in edge port.
egress-mirror1-port (port; Default: switch1-cpu)	The second egress mirroring analyzer port.
egress-sampling-ratio (1/32768..1/1; Default: 1/1)
fdb-uses (mirror0 | mirror1; Default: mirror0)	Analyzer port used for FDB-based mirroring.
forward-invalid-vlan (yes | no; Default: yes)	Whether to allow forwarding VLANs which are not members of VLAN table.
ingress-mirror-ratio (1/32768..1/1; Default: 1/1)	Proportion of ingress mirrored packets compared to all packets.
ingress-mirror0-enable (yes | no; Default: yes)	Enables or disables ingress mirroring on Mirror0 port.
ingress-mirror0-format (analyzer-configured | modified | original; Default: modified)	analyzer-configured - The packet is same as the packet to destination. VLAN format is modified based on the VLAN configurations of the analyzer port. modified - The packet is same as the packet to destination. VLAN format is modified based on the VLAN configurations of the egress port. original - Traffic is mirrored without any change to the original incoming packet format. But service VLAN tag is stripped in edge port.
ingress-mirror0-port (port; Default: switch1-cpu)	The first ingress mirroring analyzer port.
ingress-mirror1-enable (yes | no; Default: yes)	Enables or disables ingress mirroring on Mirror1 port.
ingress-mirror1-format (analyzer-configured | modified | original; Default: modified)	analyzer-configured - The packet is same as the packet to destination. VLAN format is modified based on the VLAN configurations of the analyzer port. modified - The packet is same as the packet to destination. VLAN format is modified based on the VLAN configurations of the egress port. original - Traffic is mirrored without any change to the original incoming packet format. But service VLAN tag is stripped in edge port.
ingress-mirror1-port (port; Default: switch1-cpu)	The second ingress mirroring analyzer port.
invalid-vlan-lookup-mode (ivl | svl; Default: ivl)	Lookup and learning mode for packets with invalid VLAN.
ipv4-multicast-lookup-mode (dst-ip-and-vid-for-ipv4 | dst-mac-and-vid-always; Default: dst-mac-and-vid-always)	Lookup mode for IPv4 multicast bridging. dst-mac-and-vid-always - For all packet types lookup key is destination MAC and VLAN id. dst-ip-and-vid-for-ipv4 - For IPv4 packets lookup key is destination IP and VLAN id. For other packet types lookup key is destination MAC and VLAN id.
mac-level-isolation (yes | no; Default: no)	Enables or disables MAC level isolation.
mirror-egress-if-ingress-mirrored (yes | no; Default: no)	When packet is applied to both ingress and egress mirroring, if this setting is disabled, only ingress mirroring is performed on the packet; if this setting is enabled both mirroring types are applied.
mirror-tx-on-mirror-port (yes | no; Default: no)
mirrored-packet-drop-precedence (drop | green | red | yellow; Default: green)	Remarked drop precedence in mirrored packets. This QoS attribute is used for mirrored packet enqueuing or dropping.
mirrored-packet-qos-priority (0..7; Default: 0)	Remarked priority in mirrored packets.
name (string value; Default: switch1)	Name of the switch.
override-existing-when-ufdb-full (yes | no; Default: no)	Enable or disable to override existing entry which has the lowest aging value when UFDB is full.
unicast-fdb-timeout (time interval; Default: 5m)	Timeout for Unicast FDB entries.
use-cvid-in-one2one-vlan-lookup (yes | no; Default: yes)	Whether to use customer VLAN id for 1:1 VLAN switching lookup.
use-svid-in-one2one-vlan-lookup (yes | no; Default: no)	Whether to use service VLAN id for 1:1 VLAN switching lookup.
vlan-level-isolation (yes | no; Default: no)	Enables or disables VLAN level isolation.
vlan-uses (mirror0 | mirror1; Default: mirror0)	Analyzer port used for VLAN-based mirroring.

Port Configuration

Sub-menu: /interface ethernet switch port

Property	Description
action-on-restricted-unknown-sa (copy-to-cpu | drop | forward | redirect-to-cpu; Default: forward)	Forwarding action for packets with restricted unknown source MAC address.
action-on-static-station-move (copy-to-cpu | drop | forward | redirect-to-cpu; Default: forward)	Forwarding action for packets with normal static station move.
allow-multicast-loopback (yes | no; Default: no)	Multicast loopback on port. When enabled, it permits sending back when source port and destination port are the same for registered multicast or broadcast packets.
allow-unicast-loopback (yes | no; Default: no)	Unicast loopback on port. When enabled, it permits sending back when source port and destination port are the same one for known unicast packets.
default-customer-pcp (0..7; Default: 0)	Default customer priority of the port.
default-service-pcp (0..7; Default: 0)	Default service priority of the port.
drop-counter-config (; Default: none)
drop-when-ufdb-entry-sa-drop (yes | no; Default: no)	Enable or disable to drop packets when UFDB entry has action "src-drop".
dynamic-mac-move-is-restricted-unknown-sa (yes | no; Default: no)
egress-customer-tpid (0..10000; Default: 0x8100)
egress-mirror-to (mirror0 | mirror1; Default: mirror0)	Analyzer port for port-based egress mirroring.
egress-mirroring (yes | no; Default: no)	Enable or disable egress mirroring on the port.
egress-pcp-propagation (yes | no; Default: no)	Enables or disables egress PCP propagation. If the egress port type is Edge, the customer PCP is copied from the service PCP. If the egress port type is Network, the service PCP is copied from the customer PCP.
egress-sampling (yes | no; Default: no)
egress-service-tpid (0..10000; Default: 0x88A8)
egress-vlan-lookup (according-to-bridge-type | according-to-egress-vlan-type; Default: according-to-egress-vlan-type)	Egress VLAN table (VLAN Tagging) lookup: according-to-egress-vlan-type - Lookup VLAN id is CVID when Edge port is configured, SVID when Network port is configured. according-to-bridge-type - Lookup VLAN id is CVID when customer VLAN bridge is configured, SVID when service VLAN bridge is configured. Customer tag is unmodified for edge port in service VLAN bridge.
egress-vlan-mode (tagged | unmodified | untagged; Default: unmodified)	Egress VLAN tagging action on the port.
egress-vlan-type (edge-port | network-port; Default: edge-port)	Port type for Egress VLAN lookup.
filter-priority-tagged-frame (yes | no; Default: no)	Whether to filter tagged frames with priority on the port.
filter-tagged-frame (yes | no; Default: no)	Whether to filter tagged frames on the port.
filter-untagged-frame (yes | no; Default: no)	Whether to filter untagged frames on the port.
ingress-customer-tpid (0..10000; Default: 0x8100)
ingress-mirror-to (mirror0 | mirror1; Default: mirror0)	Analyzer port for port-based ingress mirroring.
ingress-mirroring (yes | no; Default: no)	Enable or disable ingress mirroring on the port.
ingress-mirroring-according-to-vlan (yes | no; Default: no)
ingress-sampling (yes | no; Default: no)
ingress-sampling-mode (all-frames-excluding-filtered | all-frames-without-mac-error; Default: all-frames-without-mac-error)
ingress-sampling-ratio (1/32768..1/1; Default: 1/1)
ingress-service-tpid (0..10000; Default: 0x88A8)
ingress-vlan-type (edge-port | network-port; Default: edge-port)
isolation-profile (0..31; Default: 30)	Port-level isolation profile 0. Uplink port - allows the port to communicate with all ports in the device. Port-level isolation profile 1. Isolated port - allows the port to communicate only with uplink ports. Port-level isolation profile 2 - 31. Community port - allows communication among the same community ports and uplink ports.
learn (yes | no; Default: )	Enable or disable MAC address learning on the port.
learn-limit (1..1023; Default: )	Number of allowed MAC address limit of the port.
learn-restricted-unknown-sa (yes | no; Default: yes)	Enable to learn restricted unknown source MAC. Source MAC is classified as Restricted Unknown if any one of the following conditions are met: MAC address limit is disabled on the incoming port. MAC address limit is enabled on the incoming port and the number of learnt MAC addresses exceeds the MAC limit number of the port. Dynamic source MAC move is not allowed on the port and dynamic source MAC move is treated as security breach. Secure static source MAC move is not allowed on the port and security static source MAC move is treated as security breach.
mac-based-customer-vlan-for (all-frames | none | tagged-frame-only | untagged-and-priority-tagged-frame-only; Default: none)	Frame type for which applies MAC-based customer VLAN translation.
mac-based-service-vlan-for (all-frames | none | tagged-frame-only | untagged-and-priority-tagged-frame-only; Default: none)	Frame type for which applies MAC-based service VLAN translation.
mac-based-vlan-translate (yes | no; Default: no)	Enable or disable MAC-based VLAN translation on the port.
mac-vlan-type (edge-port | network-port; Default: edge-port)	Port type for MAC based VLAN translation.
pcp-propagation-for-initial-pcp (yes | no; Default: no)
per-queue-scheduling (strict-priority | wrr-group0 | wrr-group1; Default: )
priority-to-queue (; Default: 0-15:0,1:1,2:2,3:3)
qos-change-dei (yes | no; Default: no)	Whether to change DEI on the port.
qos-change-dscp (yes | no; Default: no)	Whether to change DSCP on the port.
qos-change-pcp (yes | no; Default: no)	Whether to change PCP on the port.
qos-dscp-to-dscp-mapping (yes | no; Default: no)	Enable or disable DSCP mapping on the port.
qos-pcp-dei-map-dei (; Default: 0-15:0)
qos-pcp-dei-map-drop-precedence (; Default: 0-15:green)
qos-pcp-dei-map-dscp (; Default: 0-15:0)
qos-pcp-dei-map-pcp (; Default: 0-15:0)
qos-pcp-dei-map-priority (yes | no; Default: 0-15:0)
qos-scheme-precedence (da-based | dscp-based | pcp-based | protocol-based | sa-based | vlan-based; Default: pcp-based)
secure-static-mac-move-is-restricted-unknown-sa (yes | no; Default: no)