Manual:Default Configurations

From MikroTik Wiki
Revision as of 10:04, 15 April 2011 by Marisb (talk | contribs) (Created page with '{{Versions| v5}} == List of Default Configs == ===Integrated Indoors=== <table width="1180" > <tr class="styled_table"> <th width="100"></th> <th width="40">Wan port</th> …')
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search
Version.png

Applies to RouterOS: v5

List of Default Configs

Integrated Indoors

Wan port Lan port Wireless mode ht chain ht extension dhcp-server dhcp-client Firewall NAT Default IP Mac Server
RB750 RB750G ether1 Switched ether2-ether5 - - - on lan port on wan port blocked access to wan port Masquerade wan port 192.168.88.1/24 on lan port Disabled on wan port
RB751-2n ether1 Switched ether2-ether5, bridged wlan1 with switch AP b/g/n 2412MHz 0 above-control on lan port on wan port blocked access to wan port Masquerade wan port 192.168.88.1/24 on lan port Disabled on wan port
RB1100 - - - - - - - - - 192.168.88.1/24 on ether1 -
RB1200 - - - - - - - - - 192.168.88.1/24 on ether1 -
RB2011 - - - - - - - - - 192.168.88.1/24 on ether1 -

Integrated Outdoors

Wan port Lan port Wireless mode ht chain ht extension dhcp-server dhcp-client Firewall NAT Default IP Mac Server
Groove 5 wlan1 ether1 station a/n 5300MHz 0 above control on lan port on wan port blocked access to wan port Masquerade wan port 192.168.88.1/24 on lan port Disabled on wan port
Groove A-5xx - bridged wlan1,ether1 AP a/n 5300MHz 0 - - - - - 192.168.88.1/24 on lan port -
SXT 5D wlan1 ether1 station a/n 5300MHz 0,1 above control on lan port on wan port blocked access to wan port Masquerade wan port 192.168.88.1/24 on lan port Disabled on wan port
OmniTik ether1 Switched ether2-ether5, bridged wlan1 with switch AP a/n 5300MHz 0,1 - on lan port on wan port blocked access to wan port Masquerade wan port 192.168.88.1/24 on lan port Disabled on wan port

Engineered

Wan port Lan port Wireless mode ht chain ht extension dhcp-server dhcp-client Firewall NAT Default IP Mac Server
RB450 RB450G ether1 Switched ether2-ether5 - - - on lan port on wan port blocked access to wan port Masquerade wan port 192.168.88.1/24 on lan port Disabled on wan port
RB711-5 wlan1 ether1 station a/n 5300MHz 0 above control on lan port on wan port blocked access to wan port Masquerade wan port 192.168.88.1/24 on lan port Disabled on wan port
RB711-A5 - bridged wlan1,ether1 AP a/n 5300MHz 0 - - - - - 192.168.88.1/24 on lan port -
RB711-2 wlan1 ether1 station b/g/n 2412MHz 0 above control on lan port on wan port blocked access to wan port Masquerade wan port 192.168.88.1/24 on lan port Disabled on wan port

Wan Port

When applying configuration WAN port is renamed to "<wan port>-gateway", for example, if wan port is ether1, it will be renamed to "ether1-gateway".

Local Port

Local port can be:

  • single interface
  • ethernets configured in switch group
  • bridged all interfaces that are not WAN and switch slaves.

If ports are switched then master port is renamed to "<ethernet name>-master-local" and slaves to "<ethernet name>-slave-local".

Lets take RB751 as an example. Board has ether1 configured as WAN port, it has switch chip and one pre-configured wireless interface. So in this case all ethernets except ether1 are groped in switch group and bridged with wireless interface. Here how generated config would look like: 

/interface ethernet 
set ether2 name=ether2-master-local
set ether3 name=ether3-slave-local master-port=ether2-master-local
set ether4 name=ether4-slave-local master-port=ether2-master-local
set ether5 name=ether5-slave-local master-port=ether2-master-local

/interface bridge 
add name="bridge-local" auto-mac=no protocol-mode=rstp admin-mac=[/interface ethernet get [find name~"ether2"] mac-address];

/interface bridge port
add bridge=bridge-local interface=wlan1
add bridge=bridge-local interface=ether2-master-local

Wireless Config

Wireless configuration depends on market segment for which board is designed. It can be configured as AP or station in 2GHz and 5GHz frequencies. Default 2GHz frequency is 2412 and default 5GHz frequency is 5300. SSID is "Mikrotik".

If board has two chains (letter D in the naming of the board), then both chains are enabled. HT Extension is enabled on all CPEs.

Code from default config. Variables mode, band, htChains and htExt are determined based on type of the board (See table above). 

/interface wireless set wlan1 mode=$mode band=$band ht-txchains=$htChains ht-rxchains=$htChains \
	ht-extension-channel=$htExt disabled=no country=no_country_set wireless-protocol=any

Default IP and DHCP Config

Default IP address on all boards is 192.168.88.1/24. Boards without specific configuration has IP address set on ether1, other boards has IP address on LAN interface.

All boards that has WAN port configured, DHCP client is set on WAN port.

Typically on all CPEs DHCP server is set on LAN port, giving out addresses in range from 192.168.88.2-192.168.88.254

As an example RB751 applied DHCP config. 

/ip dhcp-client add interface=ether1-gateway disabled=no

/ip pool add name="default-dhcp" ranges=192.168.88.10-192.168.88.254;
/ip dhcp-server 
  add name=default address-pool="default-dhcp" interface=bridge-local disabled=no;

/ip dhcp-server network 
  add address=192.168.88.0/24 gateway=192.168.88.1 dns-server=192.168.88.1 comment="default configuration";

Firewall, NAT and MAC server

All boards with configured WAN port has configured protection on that port. Any traffic leaving WAN port is masqueraded.

Config example: 

/ip firewall {
	filter add chain=input action=accept protocol=icmp comment="default configuration"
	filter add chain=input action=accept connection-state=established in-interface="$wanPort-gateway" comment="default configuration"
	filter add chain=input action=accept connection-state=related in-interface="$wanPort-gateway" comment="default configuration"
	filter add chain=input action=drop in-interface="$wanPort-gateway" comment="default configuration"
	nat add chain=srcnat out-interface="$wanPort-gateway" action=masquerade comment="default configuration"
}
/tool mac-server remove [find];
/tool mac-server mac-winbox disable [find];
:foreach k in=[/interface find] do={
	:local tmpName [/interface get $k name];
	:if (!($tmpName~$wanPort)) do={
		/tool mac-server add interface=$tmpName disabled=no;
		/tool mac-server mac-winbox add interface=$tmpName disabled=no;
	}
}

/ip neighbor discovery set [find name="$wanPort-gateway"] discover=no

DNS

Every board allows remote DNS requests and static DNS name is pre-configured. 

	/ip dns {
		set allow-remote-requests=yes
		static add name=router address=192.168.88.1
	}


[ Top | Back to Content ]

Retrieved from "https://wiki.mikrotik.com/index.php?title=Manual:Default_Configurations&oldid=20820"