Manual:First time startup: Difference between revisions

From MikroTik Wiki
Jump to navigation Jump to search
m (Reverted edit of Rock on all you f little dudes!, changed back to last version by Normis)
 
(42 intermediate revisions by 4 users not shown)
Line 1: Line 1:
{{Versions| All }}
== Overview ==
After you have installed the RouterOS software, or turned on the Router for the first time, there are various ways how to connect to it:
After you have installed the RouterOS software, or turned on the Router for the first time, there are various ways how to connect to it:
* Accessing Command Line Interface ([[M:Console |CLI]]) via Telnet, SSH, serial cable or even keyboard and monitor if your router has a VGA card.
* Accessing Web based GUI ([[M:Webfig |WebFig]])
* Using the [[M:Winbox | WinBox]] configuration utility (Windows app, compatible with Wine)
Every router is factory pre-configured with the IP address 192.168.88.1/24 on the ether1 port. The default username is '''admin''' with no password. After you log in for the first time, please create a new user with a password in the "full" group, re-login and delete the default admin user. We highly recommend you to follow the general guidelines of the article [[Manual:Securing_Your_Router | Securing your router]] to protect the device from any unauthorised access.
Additional configuration may be set depending on RouterBOARD model. Most models have the ether1 configured as a WAN port and any communication with the router through that port is not possible, since it is firewalled to protect from any outside access. List of RouterBOARD models and their default configurations can be found in [[Manual:Default_Configurations | this]] article.


== Winbox ==


= Monitor and Keyboard =
Winbox is a configuration utility that can connect to the router via MAC or IP protocol.
Latest winbox version can be downloaded from our [https://mikrotik.com/download download page].


Run the Winbox utility, then click the '''[...]''' button and see if Winbox finds your Router and it's MAC address. Winbox neighbor discovery will discover all routers on the broadcast network. If you see routers on the list, connect to it by clicking on MAC address and pressing '''Connect''' button.


Simply attach a monitor to the video card connector of the computer ''(note: RouterBOARD products don't have this)'' and see what happens on the screen. You should see a login promt like this:
[[File:Winbox-loader2.png | 400px]]


  MikroTik v2.9.12
Winbox will try download plugins from the router, if it is connecting for the first time to the router with current version. Note that it may take up to one minute to download all plugins if winbox is connected with MAC protocol.
After winbox have successfully downloaded plugins and authenticated, main window will be displayed:
 
[[File:Winbox-workarea.png | 740px]]
 
If winbox cannot find any routers, make sure that your Windows computer is directly connected to the router with an Ethernet cable, or at least they both are connected to the same switch. As MAC connection works on Layer2, it is possible to connect to the router even without IP address configuration. Due to the use of broadcasting MAC connection is not stable enough to use continuously, therefore it is not wise to use it on a real production / live network!. MAC connection should be used only for initial configuration.
 
Follow [[M:Winbox | winbox manual]] for more information.
 
== QuickSet and WebFig ==
 
If you have a router with default configuration, the IP address of the router can be used to connect to the Web interface. The first screen to come up will be QuickSet, where you can set the password and basic settings to secure your device. For more advanced settings, click the WebFig button to open the Advanced mode, which has almost the same configuration functionality as [[#Winbox | Winbox]].
 
[[File:Quickset.jpg | 800px ]]
 
Please see following articles to learn more about web interface configuration:
 
* [[Manual:Initial_Configuration | Initial Configuration with WebFig]]
* [[Manual:Webfig | General WebFig Manual]]
 
== CLI ==
 
Command Line Interface (CLI) allows configuration of the router's settings using text commands. Since there is a lot of available commands, they are split into groups organized in a way of hierarchical menu levels. Follow [[Manual:Console | console manual]] for CLI syntax and commands.
 
There are several ways how to access CLI:
* Winbox terminal menu
* Telnet
* SSH
* serial cable etc.
 
 
=== Serial Cable ===
 
If your device has a Serial port, you can use a console cable (or [[Null modem cable]])
 
Plug one end of the serial cable into the console port (also known as a serial port or DB9 RS232C asynchronous serial port) of the RouterBOARD and the other end in your PC (which hopefully runs Windows or Linux). You can also use a USB-Serial adapter. Run a terminal program (HyperTerminal, or Putty on Windows) with the following parameters for All RouterBOARD models except 230:
 
115200bit/s, 8 data bits, 1 stop bit, no parity, flow control=none by default.
 
RouterBOARD 230 parameters are:
 
9600bit/s, 8 data bits, 1 stop bit, no parity, hardware (RTS/CTS) flow control by default.
 
If parameters are set correctly you should be able to see login prompt.
Now you can access router by entering username and password:
<pre>
MikroTik 4.15
MikroTik Login:
 
  MMM      MMM      KKK                          TTTTTTTTTTT      KKK
  MMMM    MMMM      KKK                          TTTTTTTTTTT      KKK
  MMM MMMM MMM  III  KKK  KKK  RRRRRR    OOOOOO      TTT    III  KKK  KKK
  MMM  MM  MMM  III  KKKKK    RRR RRR  OOO  OOO    TTT    III  KKKKK
  MMM      MMM  III  KKK KKK  RRRRRR    OOO  OOO    TTT    III  KKK KKK
  MMM      MMM  III  KKK  KKK  RRR  RRR  OOOOOO      TTT    III  KKK  KKK
 
  MikroTik RouterOS 4.15 (c) 1999-2010      http://www.mikrotik.com/
 
 
[admin@MikroTik] >
 
</pre>
 
Detailed description of CLI login is in [[Manual:Console_login_process | login process section]].
 
=== Monitor and Keyboard ===
 
If your device has a graphics card (ie. regular PC) simply attach a monitor to the video card connector of the computer ''(note: RouterBOARD products don't have this, so use Method 1 or 2)'' and see what happens on the screen. You should see a login promt like this:
 
MikroTik v3.16
  Login:
  Login:
   
   
Line 19: Line 102:
   MMM      MMM  III  KKK  KKK  RRR  RRR  OOOOOO      TTT    III  KKK  KKK  
   MMM      MMM  III  KKK  KKK  RRR  RRR  OOOOOO      TTT    III  KKK  KKK  
   
   
   MikroTik RouterOS 2.9.8 (c) 1999-2005       http://www.mikrotik.com/
   MikroTik RouterOS 3.16 (c) 2008       http://www.mikrotik.com/
   
   
   
   
Line 29: Line 112:
''This method works with any device that has a video card and keyboard connector''
''This method works with any device that has a video card and keyboard connector''


= Console Cable =
If your device is a RouterBOARD then it doesn't have a monitor connector. You will have to find a console cable (or [[Null modem cable]]), plug one end into the console port (also known as a serial port or DB9 RS232C asynchronous serial port) of the RouterBOARD and the other end in your PC (which hopefully runs Windows or Linux). Run a terminal program (HyperTerminal on Windows) with the following parameters for RouterBOARD 500:
115200bit/s, 8 data bits, 1 stop bit, no parity, hardware (RTS/CTS) flow control by default.
or for RouterBOARD 200:
9600bit/s, 8 data bits, 1 stop bit, no parity, hardware (RTS/CTS) flow control by default.
and you should be conneced to the Router and can start by logging in and  issuing the '''setup''' command (see top of the page for details).
''This method works with any PC or hardware device that has a Serial Port.''
= Winbox and MAC telnet =


You can download the Winbox application from here: [http://demo2.mt.lv/winbox/winbox.exe demo2.mt.lv]. Make sure that your Windows computer is directly connected to the router with an Ethernet cable, or at least that they both are connected to the same switch.
{{cont}}
Run Winbox, then click the '''...''' button and see if Winbox finds your Router and it's MAC address. If yes, connect to it and the winbox GUI interface will be shown. Follow the [http://www.mikrotik.com/docs/ros/2.9/ manual] about configuring the router


''This method works with any device that runs RouterOS''
[[Category:Manual|First time]]
[[Category:Basic|First time]]
[[Category:Console|First time]]

Revision as of 08:30, 27 April 2017

Version.png

Applies to RouterOS: All

Overview

After you have installed the RouterOS software, or turned on the Router for the first time, there are various ways how to connect to it:

  • Accessing Command Line Interface (CLI) via Telnet, SSH, serial cable or even keyboard and monitor if your router has a VGA card.
  • Accessing Web based GUI (WebFig)
  • Using the WinBox configuration utility (Windows app, compatible with Wine)

Every router is factory pre-configured with the IP address 192.168.88.1/24 on the ether1 port. The default username is admin with no password. After you log in for the first time, please create a new user with a password in the "full" group, re-login and delete the default admin user. We highly recommend you to follow the general guidelines of the article Securing your router to protect the device from any unauthorised access.

Additional configuration may be set depending on RouterBOARD model. Most models have the ether1 configured as a WAN port and any communication with the router through that port is not possible, since it is firewalled to protect from any outside access. List of RouterBOARD models and their default configurations can be found in this article.

Winbox

Winbox is a configuration utility that can connect to the router via MAC or IP protocol. Latest winbox version can be downloaded from our download page.

Run the Winbox utility, then click the [...] button and see if Winbox finds your Router and it's MAC address. Winbox neighbor discovery will discover all routers on the broadcast network. If you see routers on the list, connect to it by clicking on MAC address and pressing Connect button.

Winbox-loader2.png

Winbox will try download plugins from the router, if it is connecting for the first time to the router with current version. Note that it may take up to one minute to download all plugins if winbox is connected with MAC protocol. After winbox have successfully downloaded plugins and authenticated, main window will be displayed:

Winbox-workarea.png

If winbox cannot find any routers, make sure that your Windows computer is directly connected to the router with an Ethernet cable, or at least they both are connected to the same switch. As MAC connection works on Layer2, it is possible to connect to the router even without IP address configuration. Due to the use of broadcasting MAC connection is not stable enough to use continuously, therefore it is not wise to use it on a real production / live network!. MAC connection should be used only for initial configuration.

Follow winbox manual for more information.

QuickSet and WebFig

If you have a router with default configuration, the IP address of the router can be used to connect to the Web interface. The first screen to come up will be QuickSet, where you can set the password and basic settings to secure your device. For more advanced settings, click the WebFig button to open the Advanced mode, which has almost the same configuration functionality as Winbox.

Quickset.jpg

Please see following articles to learn more about web interface configuration:

CLI

Command Line Interface (CLI) allows configuration of the router's settings using text commands. Since there is a lot of available commands, they are split into groups organized in a way of hierarchical menu levels. Follow console manual for CLI syntax and commands.

There are several ways how to access CLI:

  • Winbox terminal menu
  • Telnet
  • SSH
  • serial cable etc.


Serial Cable

If your device has a Serial port, you can use a console cable (or Null modem cable)

Plug one end of the serial cable into the console port (also known as a serial port or DB9 RS232C asynchronous serial port) of the RouterBOARD and the other end in your PC (which hopefully runs Windows or Linux). You can also use a USB-Serial adapter. Run a terminal program (HyperTerminal, or Putty on Windows) with the following parameters for All RouterBOARD models except 230:

115200bit/s, 8 data bits, 1 stop bit, no parity, flow control=none by default.

RouterBOARD 230 parameters are:

9600bit/s, 8 data bits, 1 stop bit, no parity, hardware (RTS/CTS) flow control by default.

If parameters are set correctly you should be able to see login prompt. Now you can access router by entering username and password:

MikroTik 4.15
MikroTik Login: 

  MMM      MMM       KKK                          TTTTTTTTTTT      KKK
  MMMM    MMMM       KKK                          TTTTTTTTTTT      KKK
  MMM MMMM MMM  III  KKK  KKK  RRRRRR     OOOOOO      TTT     III  KKK  KKK
  MMM  MM  MMM  III  KKKKK     RRR  RRR  OOO  OOO     TTT     III  KKKKK
  MMM      MMM  III  KKK KKK   RRRRRR    OOO  OOO     TTT     III  KKK KKK
  MMM      MMM  III  KKK  KKK  RRR  RRR   OOOOOO      TTT     III  KKK  KKK

  MikroTik RouterOS 4.15 (c) 1999-2010       http://www.mikrotik.com/


[admin@MikroTik] > 

Detailed description of CLI login is in login process section.

Monitor and Keyboard

If your device has a graphics card (ie. regular PC) simply attach a monitor to the video card connector of the computer (note: RouterBOARD products don't have this, so use Method 1 or 2) and see what happens on the screen. You should see a login promt like this:

MikroTik v3.16
Login:

Enter admin as the login name, and hit enter twice (because there is no password yet), you will see this screen:

  MMM      MMM       KKK                          TTTTTTTTTTT      KKK
  MMMM    MMMM       KKK                          TTTTTTTTTTT      KKK
  MMM MMMM MMM  III  KKK  KKK  RRRRRR     OOOOOO      TTT     III  KKK  KKK
  MMM  MM  MMM  III  KKKKK     RRR  RRR  OOO  OOO     TTT     III  KKKKK
  MMM      MMM  III  KKK KKK   RRRRRR    OOO  OOO     TTT     III  KKK KKK
  MMM      MMM  III  KKK  KKK  RRR  RRR   OOOOOO      TTT     III  KKK  KKK 

  MikroTik RouterOS 3.16 (c) 2008       http://www.mikrotik.com/


Terminal ansi detected, using single line input mode
[admin@router] >

Now you can start configuring the router, by issuing the setup command.

This method works with any device that has a video card and keyboard connector


[ Top | Back to Content ]