Difference between revisions of "Manual:Flashfig"

From MikroTik Wiki
Jump to: navigation, search
(Fix Bullets)
(Flashfig Description: Add Fix)
Line 3: Line 3:
 
== Flashfig Description ==
 
== Flashfig Description ==
  
Flashfig is a program that runs on Windows computer, that allows you to apply configuration to any MikroTik RouterOS device within few seconds. Flashfig program is available from [http://www.mikrotik.com/download/netinstall-4.5b.zip Netinstall].
+
Flashfig applies MikroTik RouterOS '''configuration''' to any RouterBOARD within '''3 seconds'''. Configuration can be applied to multiple RouterBOARDs in a row. All you need running Flashfig application, power attached to a RouterBOARD and Ethernet connection between Flashfig server and RouterBOARD.
  
Flashfig is used to apply MikroTik RouterOS configuration to multiple routers within few seconds. Flashfig configuration is saved and reloaded after reset-configuration was applied to a router.
+
Flashfig server runs on a Windows computer, Flashfig program is available from [http://www.mikrotik.com/download/netinstall-4.5b.zip Netinstall].
 +
 
 +
Flashfig configuration is reloaded after reset-configuration was applied to a router.
  
 
Flashfig is supported by all [http://www.routerboard.com RouterBOARDs]. It works between computer with Flashfig and RouterBOARD within the same broadcast domain (direct Ethernet network connection is required).  
 
Flashfig is supported by all [http://www.routerboard.com RouterBOARDs]. It works between computer with Flashfig and RouterBOARD within the same broadcast domain (direct Ethernet network connection is required).  
  
Flashfig mode for RouterBOARD is enable via RouterBOOT or from MikroTik RouterOS console.
+
Flashfig boot support is enabled on every RouterBOARD, which is from factory (Recently purchased RouterBOARD), alternatively it could be enabled via RouterBOOT or from MikroTik RouterOS console.
 
 
  
 
==Flashfig Example==
 
==Flashfig Example==

Revision as of 15:36, 22 February 2010

Version.png

Applies to RouterOS: v4

Flashfig Description

Flashfig applies MikroTik RouterOS configuration to any RouterBOARD within 3 seconds. Configuration can be applied to multiple RouterBOARDs in a row. All you need running Flashfig application, power attached to a RouterBOARD and Ethernet connection between Flashfig server and RouterBOARD.

Flashfig server runs on a Windows computer, Flashfig program is available from Netinstall.

Flashfig configuration is reloaded after reset-configuration was applied to a router.

Flashfig is supported by all RouterBOARDs. It works between computer with Flashfig and RouterBOARD within the same broadcast domain (direct Ethernet network connection is required).

Flashfig boot support is enabled on every RouterBOARD, which is from factory (Recently purchased RouterBOARD), alternatively it could be enabled via RouterBOOT or from MikroTik RouterOS console.

Flashfig Example

This is a step by step example of how to use Flashfig to set typical MikroTik RouterOS configuration to RouterBOARD.

Introduction

Flashfig is available from Netinstall,

Flashfig.png

Requirements

The Windows computer must be equipped with the following ports and contain the following files:

  • Ethernet port;
  • The .rsc file(s) with MikroTik RouterOS configuration (the same as export/import file);
  • The latest NetInstall/Flashfig program available from the downloads page;

The RouterBOARD:

  • Boot-device configured as flash-boot or flash-boot-once-then-nand;

Pre-Configuration

Windows Computer
  • Run Flashfig;
  • Prepare .rsc file, .rsc file is regular/import file, it accepts valid MikroTik RouterOS CLI commands. You can create .rsc file by any text-editor program (Notepad, Texteditor, TextEdit, Microsoft Word, OpenOffice Writer);

Flashfig2.png

  • Assign Boot Client Address, which should be address from the same subnet as configured on laptop Ethernet interface,

Flashfig3.png

  • Browse for .rsc MikroTik RouterOS configuration file to apply to RouterBOARD, highlight the file and Select to approve it,

Flashfig4.png

  • Activate Flashfig server, now it is ready to Flashfig. Note, any RouterBOARD will be flashfiged within the network, which is powered on with boot-device configured to flash-boot or flash-boot-once-then-nand,


Flashfig5.png

RouterBOARD

Currently you need to set pre-configuration for every RouterBOARD,

  • Access the RouterBOARD with Winbox/Console and set the configuration,
/system routerboard settings set boot-device=flash-boot

or use more preferable option,

/system routerboard settimgs set boot-device=flash-boot-once-then-nand

Your router is now ready for Flashfig.


Connect

Connect RouterBOARD with enabled boot-device as flash-boot and Windows computer with activated Flashfig to the same network or switch.

Make sure Windows firewall on computer is not blocking the communications.

Run Flashfig

  • Reboot RouterBOARD by command,
/system reboot

or unplug/plug the power of the RouterBOARD,

  • Check the status on Flashfig program,

Flashfig5.png

As soon as you will see, that router is Flashfigged, it means configuration is applied and you must hear one beep (router is rebooted) and two beeps (MikroTik RouterOS is booted up);

  • That is all, RouterBOARD has configuration from .rsc file and you can use it in production.