Difference between revisions of "Manual:Interface/Bridge"

From MikroTik Wiki
Jump to: navigation, search
(Created page with '<h2>Summary</h2> <p><b>Sub-menu:</b> <code>/interface bridge</code></p> <p><b>Standards:</b> <code>[http://standards.ieee.org/getieee802/download/802.1D-1998.pdf IEEE801.1D]</cod…')
 
Line 30: Line 30:
 
     <td><var><b>ageing-time</b></var> (<em>time</em>; Default:<b> 00:05:00</b>)</td>
 
     <td><var><b>ageing-time</b></var> (<em>time</em>; Default:<b> 00:05:00</b>)</td>
 
     <td>How long a host information will be kept in the bridge database</td>
 
     <td>How long a host information will be kept in the bridge database</td>
 +
</tr>
 +
<tr>
 +
    <td><var><b>arp</b></var> (<em>disabled | enabled | proxy-arp | reply-only</em>; Default:<b> enabled</b>)</td>
 +
    <td>Address Resolution Protocol setting</td>
 +
</tr>
 +
<tr>
 +
    <td><var><b>auto-mac</b></var> (<em>yes | no</em>; Default:<b> yes</b>)</td>
 +
    <td></td>
 +
</tr>
 +
<tr>
 +
    <td><var><b>forward-delay</b></var> (<em>time</em>; Default:<b> 00:00:15</b>)</td>
 +
    <td>Time which is spent during the initialization phase of the bridge interface (i.e., after router startup or enabling the interface) in listening/learning state before the bridge will start functioning normally</td>
 +
</tr>
 +
<tr>
 +
    <td><var><b>l2mtu</b></var> (<em>integer</em>; read-only)</td>
 +
    <td>Layer2 Maximum transmission unit. [[ Maximum_Transmission_Unit_on_RouterBoards | Read more>> ]]</td>
 +
</tr>
 +
<tr>
 +
    <td><var><b>max-message-age</b></var> (<em>time</em>; Default:<b> 00:00:20</b>)</td>
 +
    <td>How long to remember Hello messages received from other bridges</td>
 +
</tr>
 +
<tr>
 +
    <td><var><b>mtu</b></var> (<em>integer</em>; Default:<b> 1500</b>)</td>
 +
    <td>Maximum Transmission Unit</td>
 +
</tr>
 +
<tr>
 +
    <td><var><b>name</b></var> (<em>text</em>; Default:<b> bridgeN</b>)</td>
 +
    <td>Name of the bridge interface</td>
 +
</tr>
 +
<tr>
 +
    <td><var><b>priority</b></var> (<em>integer: 0..65535</em>; Default:<b> 32768</b>)</td>
 +
    <td>Bridge interface priority. The priority argument is used by Spanning Tree Protocol to determine, which port remains enabled if at least two ports form a loop</td>
 +
</tr>
 +
<tr>
 +
    <td><var><b>protocol-mode</b></var> (<em>none | rstp | stp</em>; Default:<b> none</b>)</td>
 +
    <td></td>
 +
</tr>
 +
<tr>
 +
    <td><var><b>transmit-hold-count</b></var> (<em>integer: 1..10</em>; Default:<b> 6</b>)</td>
 +
    <td></td>
 
</tr>
 
</tr>

Revision as of 14:01, 27 January 2010

Summary

Sub-menu: /interface bridge

Standards: IEEE801.1D


Ethernet-like networks (Ethernet, Ethernet over IP, IEEE802.11 in ap-bridge or bridge mode, WDS, VLAN) can be connected together using MAC bridges. The bridge feature allows the interconnection of hosts connected to separate LANs (using EoIP, geographically distributed networks can be bridged as well if any kind of IP network interconnection exists between them) as if they were attached to a single LAN. As bridges are transparent, they do not appear in traceroute list, and no utility can make a distinction between a host working in one LAN and a host working in another LAN if these LANs are bridged (depending on the way the LANs are interconnected, latency and data rate between hosts may vary).

Network loops may emerge (intentionally or not) in complex topologies. Without any special treatment, loops would prevent network from functioning normally, as they would lead to avalanche-like packet multiplication. Each bridge runs an algorithm which calculates how the loop can be prevented. STP and RSTP allows bridges to communicate with each other, so they can negotiate a loop free topology. All other alternative connections that would otherwise form loops, are put to standby, so that should the main connection fail, another connection could take its place. This algorithm exchange configuration messages (BPDU - Bridge Protocol Data Unit) periodically, so that all bridges would be updated with the newest information about changes in network topology. STP selects root bridge which is responosible for network reconfiguration, such as blocking and opening ports of the other bridges. The root bridge is the bridge with lowest bridge ID.

Bridge Interface Setup

Sub-menu: /interface bridge

To combine a number of networks into one bridge, a bridge interface should be created (later, all the desired interfaces should be set up as its ports). One MAC address will be assigned to all the bridged interfaces (the smallest MAC address will be chosen automatically).

Properties

Property Description
admin-mac (MAC address; Default: )
ageing-time (time; Default: 00:05:00) How long a host information will be kept in the bridge database
arp (disabled | enabled | proxy-arp | reply-only; Default: enabled) Address Resolution Protocol setting
auto-mac (yes | no; Default: yes)
forward-delay (time; Default: 00:00:15) Time which is spent during the initialization phase of the bridge interface (i.e., after router startup or enabling the interface) in listening/learning state before the bridge will start functioning normally
l2mtu (integer; read-only) Layer2 Maximum transmission unit. Read more>>
max-message-age (time; Default: 00:00:20) How long to remember Hello messages received from other bridges
mtu (integer; Default: 1500) Maximum Transmission Unit
name (text; Default: bridgeN) Name of the bridge interface
priority (integer: 0..65535; Default: 32768) Bridge interface priority. The priority argument is used by Spanning Tree Protocol to determine, which port remains enabled if at least two ports form a loop
protocol-mode (none | rstp | stp; Default: none)
transmit-hold-count (integer: 1..10; Default: 6)