Manual:Interface/IPIP: Difference between revisions

From MikroTik Wiki
Jump to navigation Jump to search
mNo edit summary
mNo edit summary
Line 1: Line 1:
{{Versions|2.9, v3, v4}}
{{Versions|2.9, v3, v4+}}


<div class=manual>
<div class=manual>


<h2>Summary</h2>
==Summary==
<p><b>Sub-menu:</b> <code>/interface ipip</code></p>
<p id="shbox"><b>Sub-menu:</b> <code>/interface ipip</code>
<p><b>Standards:</b> <code>IPIP RFC 2003</code></p>
<br />
<b>Standards:</b> <code>IPIP RFC 2003</code></p>
<br />
<br />
<p>
<p>
Line 18: Line 19:
</p>
</p>


<h2>Properties</h2>
==Properties==


{{Mr-arg-table-h
{{Mr-arg-table-h
Line 61: Line 62:
{{Note | There is no authentication or 'state' for this interface. The bandwidth usage of the interface may be monitored with the monitor feature from the interface menu.}}
{{Note | There is no authentication or 'state' for this interface. The bandwidth usage of the interface may be monitored with the monitor feature from the interface menu.}}


<h2>Setup examples</h2>
==Setup examples==


<p>
<p>

Revision as of 09:07, 30 April 2010

Version.png

Applies to RouterOS: 2.9, v3, v4+

Summary

Sub-menu: /interface ipip
Standards: IPIP RFC 2003


The IPIP tunneling implementation on the MikroTik RouterOS is RFC 2003 compliant. IPIP tunnel is a simple protocol that encapsulates IP packets in IP to make a tunnel between two routers. The IPIP tunnel interface appears as an interface under the interface list. Many routers, including Cisco and Linux based, support this protocol. This protocol makes multiple network schemes possible.

IP tunneling protocol adds the following possibilities to a network setups:

  • to tunnel Intranets over the Internet
  • to use it instead of source routing

Properties

Property Description
local-address (IP; Default: ) IP address on a router that will be used by IPIP tunnel
mtu (integer; Default: 1500) Layer3 Maximum transmission unit
name (string; Default: ) Interface name
remote-address (IP; Default: ) IP address of remote end of IPIP tunnel



Icon-note.png

Note: There is no authentication or 'state' for this interface. The bandwidth usage of the interface may be monitored with the monitor feature from the interface menu.


Setup examples

Suppose we want to add an IPIP tunnel between routers R1 and R2:

Ipip-sample.png

At first, we need to configure IPIP interfaces and then add IP addresses to them.

The configuration for router R1 is as follows:

[admin@MikroTik] interface ipip> add
local-address: 10.0.0.1
remote-address: 22.63.11.6
[admin@MikroTik] interface ipip> print
Flags: X - disabled, R - running
  #    NAME                               MTU   LOCAL-ADDRESS   REMOTE-ADDRESS
  0 X  ipip1                              1480  10.0.0.1        22.63.11.6

[admin@MikroTik] interface ipip> en 0
[admin@MikroTik] interface ipip> /ip address add address 1.1.1.1/24 interface=ipip1

The configuration of the R2 is shown below:

[admin@MikroTik] interface ipip> add local-address=22.63.11.6 remote-address=10.
0.0.1
[admin@MikroTik] interface ipip> print
Flags: X - disabled, R - running
  #    NAME                               MTU   LOCAL-ADDRESS   REMOTE-ADDRESS
  0 X  ipip1                              1480  22.63.11.6      10.0.0.1

[admin@MikroTik] interface ipip> enable 0
[admin@MikroTik] interface ipip> /ip address add address 1.1.1.2/24 interface=ipip1

Now both routers can ping each other:

[admin@MikroTik] interface ipip> /ping 1.1.1.2
1.1.1.2 64 byte ping: ttl=64 time=24 ms
1.1.1.2 64 byte ping: ttl=64 time=19 ms
1.1.1.2 64 byte ping: ttl=64 time=20 ms
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 19/21.0/24 ms
[admin@MikroTik] interface ipip>

[ Top | Back to Content ]