Manual:Interface/PPPoE

From MikroTik Wiki
< Manual:Interface
Revision as of 11:52, 20 July 2009 by Normis (talk | contribs) (New page: The PPPoE (Point to Point Protocol over Ethernet) protocol provides extensive user management, network management and accounting benefits to ISPs and network administrators. Currently PPPo...)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search
The printable version is no longer supported and may have rendering errors. Please update your browser bookmarks and please use the default browser print function instead.

The PPPoE (Point to Point Protocol over Ethernet) protocol provides extensive user management, network management and accounting benefits to ISPs and network administrators. Currently PPPoE is used mainly by ISPs to control client connections for xDSL and cable modems as well as plain Ethernet networks. PPPoE is an extension of the standard Point to Point Protocol (PPP). The difference between them is expressed in transport method: PPPoE employs Ethernet instead of serial modem connection.

Generally speaking, PPPoE is used to hand out IP addresses to clients based on the username (and workstation, if desired) authentication as opposed to workstation only authentication, when static IP addresses or DHCP are used. It is adviced not to use static IP addresses or DHCP on the same interfaces as PPPoE for obvious security reasons.

MikroTik RouterOS can act as a RADIUS client - you can use a RADIUS server to authenticate PPPoE clients and use accounting for them.

A PPPoE connection is composed of a client and an access concentrator (server). The client may be any computer that has the PPPoE client protocol support installed. MikroTik RouterOS supports both - client and access concentrator sides of PPPoE. The PPPoE client and server work over any Ethernet level interface on the router - wireless 802.11 (Aironet, Cisco, WaveLan, Prism, Atheros), 10/100/1000 Mbit/s Ethernet, RadioLan and EoIP (Ethernet over IP tunnel). MPPE 40bit RSA and MPPE 128bit RSA encryption is supported.

Multilink PPP (MP) is supported in order to provide MRRU (the ability to transmit full-sized 1500 and larger packets) and bridging over PPP links (using Bridge Control Protocol (BCP) that allows to send raw Ethernet frames over PPP links). This way it is possible to setup bridging without EoIP. The bridge should either have an administratively set MAC address or an Ethernet-like interface in it, as PPP links do not have MAC addresses.

Note that when RADIUS server is authenticating a user with CHAP, MS-CHAPv1 or MS-CHAPv2, the RADIUS protocol does not use shared secret, it is used only in authentication reply. So if you have a wrong shared secret, RADIUS server will accept the request. You can use /radius monitor command to see bad-replies parameter. This value should increase whenever a client tries to connect.

Supported connections

  • MikroTik RouterOS PPPoE client to any PPPoE server (access concentrator)
  • MikroTik RouterOS server (access concentrator) to multiple PPPoE clients (clients are avaliable for almost all operating systems and most routers)

PPPoE Client

Quick Setup Guide

To configure MikroTik RouterOS to be a PPPoE client

Just add a pppoe-client:

/interface pppoe-client add name=pppoe-user-mike user=user password=passwd interface=wlan1 service-name=internet disabled=no

To configure MikroTik RouterOS to be an Access Concentrator (PPPoE Server)

Add an address pool for the clients from 10.1.1.62 to 10.1.1.72, called pppoe-pool:

/ip pool add name="pppoe-pool" ranges=10.1.1.62-10.1.1.72

Add PPP profile, called pppoe-profile where local-address will be the router's address and clients will have an address from pppoe-pool:

/ppp profile add name="pppoe-profile" local-address=10.1.1.1 remote-address=pppoe-pool

Add a user with username mike and password 123:

/ppp secret add name=user password=passwd service=pppoe profile=pppoe-profile

Now add a pppoe server:

/interface pppoe-server server add service-name=internet interface=wlan1 default-profile=pppoe-profile

Specifications

  • Packages required: ppp
  • License required: Level1 (limited to 1 interface) , Level3 (limited to 200 interfaces) , Level4 (limited to 200 interfaces) , Level5 (limited to 500 interfaces) , Level6 (unlimited)
  • Submenu level: /interface pppoe-server, /interface pppoe-client
  • Standards and Technologies: PPPoE (RFC 2516)
  • Hardware usage: PPPoE server may require additional RAM (uses approx. 9KiB (plus extra 10KiB for packet queue, if data rate limitation is used) for each connection) and CPU power. Maximum of 65535 connections is supported.

Additional Resources

Links for PPPoE documentation:

PPPoE Clients:

  • RASPPPoE for Windows 95, 98, 98SE, ME, NT4, 2000, XP, .NET


PPPoE Client Setup

Submenu level: /interface pppoe-client

Property Description

  • ac-name (text; default: "") - this may be left blank and the client will connect to any access concentrator that offers the "service" name selected
  • add-default-route (yes | no; default: no) - whether to add a default route automatically
  • allow (multiple choice: mschap2, mschap1, chap, pap; default: mschap2, mschap1, chap, pap) - the protocol to allow the client to use for authentication
  • dial-on-demand (yes | no; default: no) - connects to AC only when outbound traffic is generated and disconnects when there is no traffic for the period set in the idle-timeout value
  • interface (name) - interface the PPPoE server can be reached through
  • max-mru (integer; default: 1460) - Maximum Receive Unit. The optimal value is the MRU of the interface the tunnel is working over decreased by 40 (so, for 1500-byte Ethernet link, set the MRU to 1460 to avoid fragmentation of packets)
  • max-mtu (integer; default: 1460) - Maximum Transmission Unit. The optimal value is the MTU of the interface the tunnel is working over decreased by 40 (so, for 1500-byte Ethernet link, set the MTU to 1460 to avoid fragmentation of packets)
  • mrru (integer: 512..65535; default: disabled) - maximum packet size that can be received on the link. If a packet is bigger than tunnel MTU, it will be split into multiple packets, allowing full size IP or Ethernet packets to be sent over the tunnel
  • disabled - disable MRRU on this link
  • name (name; default: pppoe-out1) - name of the PPPoE interface
  • password (text; default: "") - a user password used to connect the PPPoE server
  • profile (name) - default profile for the connection
  • service-name (text; default: "") - specifies the service name set on the access concentrator. Leave it blank unless you have many *services and need to specify the one you need to connect to
  • use-peer-dns (yes | no; default: no) - whether to set the router's default DNS to the PPP peer DNS (i.e. whether to get DNS settings from the peer)
  • user (text; default: "") - a user name that is present on the PPPoE server

Notes

Note for Windows. Some connection instructions may use the form where the "phone number", such as "MikroTik_AC\mt1", is specified to indicate that "MikroTik_AC" is the access concentrator name and "mt1" is the service name.

Specifying MRRU means enabling MP (Multilink PPP) over single link. This protocol is used to split big packets into smaller ones. Under Windows it can be enabled in Networking tag, Settings button, "Negotiate multi-link for single link connections". Their MRRU is hardcoded to 1614. This setting is usefull to overcome PathMTU discovery failures. The MP should be enabled on both peers.

Example

To add and enable PPPoE client on the ether1 interface connecting to the AC that provides testSN service using user name user with the password passwd:

[admin@RemoteOffice] interface pppoe-client> add interface=ether1 service-name=testSN user=user password=passwd disabled=no
[admin@RemoteOffice] interface pppoe-client> print
Flags: X - disabled, R - running
 0  R name="pppoe-out1" max-mtu=1480 max-mru=1480 mrru=disabled interface=ether1
      user="user" password="passwd" profile=default service-name="testSN"
      ac-name="" add-default-route=no dial-on-demand=no use-peer-dns=no
      allow=pap,chap,mschap1,mschap2
[admin@RemoteOffice] interface pppoe-client>

Monitoring PPPoE Client

Command name: /interface pppoe-client monitor

Property Description

  • ac-mac (MAC address) - MAC address of the access concentrator (AC) the client is connected to
  • ac-name (text) - name of the AC the client is connected to
  • encoding (text) - encryption and encoding (if asymmetric, separated with '/') being used in this connection
  • mru (read-only: integer) - effective MRU of the link
  • mtu (read-only: integer) - effective MTU of the link
  • service-name (text) - name of the service the client is connected to
  • status (text) - status of the client
  • dialing - attempting to make a connection
  • verifying password... - connection has been established to the server, password verification in progress
  • connected - self-explanatory
  • terminated - interface is not enabled or the other side will not establish a connection
  • uptime (time) - connection time displayed in days, hours, minutes and seconds

Example

To monitor the pppoe-out1 connection:

[admin@MikroTik] interface pppoe-client> monitor pppoe-out1

       status: "connected"
       uptime: 6s
    idle-time: 6s
     encoding: "MPPE128 stateless"
 service-name: "testSN"
      ac-name: "MikroTik"
       ac-mac: 00:0C:42:04:00:73
          mtu: 1480
          mru: 1480

[admin@MikroTik] interface pppoe-client> PPPoE Server Setup (Access Concentrator)

Submenu level: /interface pppoe-server server Description

The PPPoE server (access concentrator) supports multiple servers for each interface - with differing service names. Currently the throughput of the PPPoE server has been tested to 160 Mb/s on a Celeron 600 CPU. Using higher speed CPUs, throughput should increase proportionately.

The access concentrator name and PPPoE service name are used by clients to identity the access concentrator to register with. The access concentrator name is the same as the identity of the router displayed before the command prompt. The identity may be set within the /system identity submenu.

Note that if no service name is specified in WindowsXP, it will use only service with no name. So if you want to serve WindowsXP clients, leave your service name empty.

Property Description

  • authentication (multiple choice: mschap2 | mschap1 | chap | pap; default: mschap2, mschap1, chap, pap) - authentication algorithm
  • default-profile (name; default: default) - default user profile to use
  • interface (name) - interface, which the clients are connected to
  • keepalive-timeout (time; default: 10) - defines the time period (in seconds) after which the router is starting to send keepalive *packets every second. If no traffic and no keepalive responses has came for that period of time (i.e. 2 * keepalive-timeout), not *responding client is proclaimed disconnected.
  • max-mru (integer; default: 1480) - Maximum Receive Unit. The optimal value is the MTU of the interface the tunnel is working over *decreased by 20 (so, for 1500-byte Ethernet link, set the MTU to 1480 to avoid fragmentation of packets)
  • max-mtu (integer; default: 1480) - Maximum Transmission Unit. The optimal value is the MTU of the interface the tunnel is working over decreased by 20 (so, for 1500-byte Ethernet link, set the MTU to 1480 to avoid fragmentation of packets)
  • max-sessions (integer; default: 0) - maximum number of clients that the AC can serve

0 - unlimited

  • mrru (integer: 512..65535; default: disabled) - maximum packet size that can be received on the link. If a packet is bigger than tunnel MTU, it will be split into multiple packets, allowing full size IP or Ethernet packets to be sent over the tunnel
  • disabled - disable MRRU on this link
  • one-session-per-host (yes | no; default: no) - allow only one session per host (determined by MAC address). If a host will try to establish a new session, the old one will be closed
  • service-name (text) - the PPPoE service name

=Notes

The default keepalive-timeout value of 10 is OK in most cases. If you set it to 0, the router will not disconnect clients until they explicitly log out or the router is restarted. To resolve this problem, the one-session-per-host property can be used.

Security issue: do not assign an IP address to the interface you will be receiving the PPPoE requests on.

Specifying MRRU means enabling MP (Multilink PPP) over single link. This protocol is used to split big packets into smaller ones. Under Windows it can be enabled in Networking tag, Settings button, "Negotiate multi-link for single link connections". Their MRRU is hardcoded to 1614. This setting is usefull to overcome PathMTU discovery failures. The MP should be enabled on both peers.

Example

To add PPPoE server on ether1 interface providing ex service and allowing only one connection per host:

[admin@MikroTik] interface pppoe-server server> add interface=ether1 service-name=ex one-session-per-host=yes
[admin@MikroTik] interface pppoe-server server> print
Flags: X - disabled
  0 X service-name="ex" interface=ether1 mtu=1480 mru=1480 mrru=disabled
      authentication=mschap2,mschap,chap,pap keepalive-timeout=10
      one-session-per-host=yes max-sessions=0 default-profile=default
[admin@MikroTik] interface pppoe-server server>

PPPoE Server

Submenu level: /interface pppoe-server

There are two types of interface (tunnel) items in PPTP server configuration - static users and dynamic connections. An interface is created for each tunnel established to the given server. Static interfaces are added administratively if there is a need to reference the particular interface name (in firewall rules or elsewhere) created for the particular user. Dynamic interfaces are added to this list automatically whenever a user is connected and its username does not match any existing static entry (or in case the entry is active already, as there can not be two separate tunnel interfaces referenced by the same name). Dynamic interfaces appear when a user connects and disappear once the user disconnects, so it is impossible to reference the tunnel created for that use in router configuration (for example, in firewall), so if you need a persistent rules for that user, create a static entry for him/her. Otherwise it is safe to use dynamic configuration. Note that in both cases PPP users must be configured properly - static entries do not replace PPP configuration.

Property Description

  • encoding (read-only: text) - encryption and encoding (if asymmetric, separated with '/') being used in this connection
  • mru (read-only: integer) - client's MRU
  • mtu (read-only: integer) - client's MTU
  • name (name) - interface name
  • remote-address (read-only: MAC address) - MAC address of the connected client
  • service (name) - name of the service the user is connected to
  • uptime (read-only: time) - shows how long the client is connected
  • user (name) - the name of the connected user (must be present in the user darabase anyway)

Example

To view the currently connected users:

[admin@MikroTik] interface pppoe-server> print
Flags: X - disabled, D - dynamic, R - running 
 #     NAME       USER      SERVICE   REMOTE... ENCODING  UPTIME
 0  DR <pppoe-ex> user      ex        00:0C:... MPPE12... 40m45s
[admin@MikroTik] interface pppoe-server>

To disconnect the user ex:

[admin@MikroTik] interface pppoe-server> remove [find user=ex]
[admin@MikroTik] interface pppoe-server> print
[admin@MikroTik] interface pppoe-server>

Application Examples

PPPoE in a multipoint wireless 802.11g network

In a wireless network, the PPPoE server may be attached to an Access Point (as well as to a regular station of wireless infrastructure). Either our RouterOS client or Windows PPPoE clients may connect to the Access Point for PPPoE authentication. Further, for RouterOS clients, the radio interface may be set to MTU 1600 so that the PPPoE interface may be set to MTU 1500. This optimizes the transmission of 1500 byte packets and avoids any problems associated with MTUs lower than 1500. It has not been determined how to change the MTU of the Windows wireless interface at this moment.

Let us consider the following setup where the MikroTik Wireless AP offers wireless clients transparent access to the local network with authentication:

First of all, the wireless interface should be configured:

[admin@PPPoE-Server] interface wireless> set 0 mode=ap-bridge \
   frequency=2442 band=2.4ghz-b/g ssid=mt disabled=no
[admin@PPPoE-Server] interface wireless> print
Flags: X - disabled, R - running 
 0 X  name="wlan1" mtu=1500 mac-address=00:0C:42:18:5C:3D arp=enabled
      interface-type=Atheros AR5413 mode=ap-bridge ssid="mt" frequency=2442
      band=2.4ghz-b/g scan-list=default antenna-mode=ant-a wds-mode=disabled
      wds-default-bridge=none wds-ignore-ssid=no default-authentication=yes
      default-forwarding=yes default-ap-tx-limit=0 default-client-tx-limit=0
      hide-ssid=no security-profile=default compression=no
[admin@PPPoE-Server] interface wireless>

Now, configure the Ethernet interface, add the IP address and set the default route:

[admin@PPPoE-Server] ip address> add address=10.1.0.3/24 interface=Local
[admin@PPPoE-Server] ip address> print
Flags: X - disabled, I - invalid, D - dynamic
 #   ADDRESS            NETWORK         BROADCAST       INTERFACE
 0   10.1.0.3/24        10.1.0.0        10.1.0.255      Local
[admin@PPPoE-Server] ip address> /ip route
[admin@PPPoE-Server] ip route> add gateway=10.1.0.1
[admin@PPPoE-Server] ip route> print
Flags: X - disabled, A - active, D - dynamic, 
C - connect, S - static, r - rip, b - bgp, o - ospf, m - mme, 
B - blackhole, U - unreachable, P - prohibit 
 #      DST-ADDRESS        PREF-SRC        G GATEWAY         DISTANCE INTER...
 0 ADC  10.1.0.0/24        10.1.0.3                          0        Local
 1 A S  0.0.0.0/0                          r 10.1.0.1        1        Local
[admin@PPPoE-Server] ip route> /interface ethernet
[admin@PPPoE-Server] interface ethernet> set Local arp=proxy-arp
[admin@PPPoE-Server] interface ethernet> print
Flags: X - disabled, R - running
 #    NAME                                   MTU   MAC-ADDRESS       ARP
 0  R Local                                  1500  00:0C:42:03:25:53 proxy-arp
[admin@PPPoE-Server] interface ethernet>

We should add PPPoE server to the wireless interface:

[admin@PPPoE-Server] interface pppoe-server server> add interface=wlan1 \
   service-name=mt one-session-per-host=yes disabled=no
[admin@PPPoE-Server] interface pppoe-server server> print
Flags: X - disabled
 0   service-name="mt" interface=wlan1 max-mtu=1480 max-mru=1480 mrru=disabled
     authentication=pap,chap,mschap1,mschap2 keepalive-timeout=10
     one-session-per-host=yes max-sessions=0 default-profile=default
[admin@PPPoE-Server] interface pppoe-server server>
Finally, we can set up PPPoE clients:

[admin@PPPoE-Server] ip pool> add name=pppoe ranges=10.1.0.100-10.1.0.200
[admin@PPPoE-Server] ip pool> print
 # NAME                                         RANGES
 0 pppoe                                        10.1.0.100-10.1.0.200
[admin@PPPoE-Server] ip pool> /ppp profile
[admin@PPPoE-Server] ppp profile> set default use-encryption=yes \
   local-address=10.1.0.3 remote-address=pppoe
[admin@PPPoE-Server] ppp profile> print
Flags: * - default
 0 * name="default" local-address=10.1.0.3 remote-address=pppoe
     use-compression=no use-vj-compression=no use-encryption=yes only-one=no
     change-tcp-mss=yes

 1 * name="default-encryption" use-compression=default
     use-vj-compression=default use-encryption=yes only-one=default
     change-tcp-mss=default
[admin@PPPoE-Server] ppp profile> .. secret
[admin@PPPoE-Server] ppp secret> add name=w password=wkst service=pppoe
[admin@PPPoE-Server] ppp secret> add name=l password=ltp service=pppoe
[admin@PPPoE-Server] ppp secret> print
Flags: X - disabled
 #   NAME        SERVICE CALLER-ID PASSWORD  PROFILE            REMOTE-ADDRESS
 0   w           pppoe             wkst      default            0.0.0.0
 1   l           pppoe             ltp       default            0.0.0.0
[admin@PPPoE-Server] ppp secret>

Thus we have completed the configuration and added two users: w and l who are able to connect to Internet, using PPPoE client software.

Note that Windows XP built-in client supports encryption, but RASPPPOE does not. So, if it is planned not to support Windows clients older than Windows XP, it is recommended not to require encryption. In other case, the server will accept clients that do not encrypt data.

Troubleshooting

I can connect to my PPPoE server. The ping goes even through it, but I still cannot open web pages

Make sure that you have specified a valid DNS server in the router (in /ip dns or in /ppp profile the dns-server parameter).

The PPPoE server shows more than one active user entry for one client, when the clients disconnect, they are still shown and active

Set the keepalive-timeout parameter (in the PPPoE server configuration) to 10 if You want clients to be considered logged off if they do not respond for 10 seconds.

Note that if the keepalive-timeout parameter is set to 0 and the only-one parameter (in PPP profile settings) is set to yes then the clients might be able to connect only once. To resolve this problem one-session-per-host parameter in PPPoE server configuration should be set to yes

My Windows XP client cannot connect to the PPPoE server

You have to specify the "Service Name" in the properties of the XP PPPoE client. If the service name is not set, or it does not match the service name of the MikroTik PPPoE server, you get the "line is busy" errors, or the system shows "verifying password - unknown error"

I want to have logs for PPPoE connection establishment

Configure the logging feature under the /system logging facility and enable the PPP type logs