PPTP is a secure tunnel for transporting IP traffic using PPP. PPTP encapsulates PPP in virtual lines that run over IP. PPTP incorporates PPP and MPPE (Microsoft Point to Point Encryption) to make encrypted links. The purpose of this protocol is to make well-managed secure connections between routers as well as between routers and PPTP clients (clients are available for and/or included in almost all OSs including Windows).
Multilink PPP (MP) is supported in order to provide MRRU (the ability to transmit full-sized 1500 and larger packets) and bridging over PPP links (using Bridge Control Protocol (BCP) that allows to send raw Ethernet frames over PPP links). This way it is possible to setup bridging without EoIP. The bridge should either have an administratively set MAC address or an Ethernet-like interface in it, as PPP links do not have MAC addresses.
PPTP includes PPP authentication and accounting for each PPTP connection. Full authentication and accounting of each connection may be done through a RADIUS client or locally.
MPPE 40bit RC4 and MPPE 128bit RC4 encryption are supported.
PPTP traffic uses TCP port 1723 and IP protocol GRE (Generic Routing Encapsulation, IP protocol ID 47), as assigned by the Internet Assigned Numbers Authority (IANA). PPTP can be used with most firewalls and routers by enabling traffic destined for TCP port 1723 and protocol 47 traffic to be routed through the firewall or router.
PPTP connections may be limited or impossible to setup though a masqueraded/NAT IP connection. Please see the Microsoft and RFC links listed below for more information.
|add-default-route (yes | no; Default: no)||Whether to add PPTP remote address as a default route.|
|allow (mschap2 | mschap1 | chap | pap; Default: mschap2, mschap1, chap, pap)||Allowed authentication methods.|
|connect-to (IP; Default: )||Remote address of PPTP server|
|dial-on-demand (yes | no; Default: no)|
|disabled (yes | no; Default: yes)||Whether interface is disabled or not. By default it is disabled|
|max-mru (integer; Default: 1460)||Maximum Receive Unit. Max packet size that PPTP interface will be able to receive without packet fragmentation.|
|max-mtu (integer; Default: 1460)||Maximum Transmission Unit. Max packet size that PPTP interface will be able to send without packet fragmentation.|
|mrru (disabled | integer; Default: disabled)||Maximum packet size that can be received on the link. If a packet is bigger than tunnel MTU, it will be split into multiple packets, allowing full size IP or Ethernet packets to be sent over the tunnel.
|name (string; Default: )||Descriptive name of the interface.|
|password (string; Default: "")||Password used for authentication.|
|profile (name; Default: default-encryption)||Used PPP profile.|
|user (string; Default: )||User name used for authentication.|
This example demonstrates how to set up PPTP client with username "pptp-hm", password "123" and server 10.1.101.100
[admin@dzeltenais_burkaans] /interface pptp-client>add name=pptp-hm user=pptp-hm password=123 \ \... connect-to=10.1.101.100 disabled=no [admin@dzeltenais_burkaans] /interface pptp-client> print detail Flags: X - disabled, R - running 0 name="pptp-hm" max-mtu=1460 max-mru=1460 mrru=disabled connect-to=10.1.101.100 user="pptp-hm" password="123" profile=default-encryption add-default-route=no dial-on-demand=no allow=pap,chap,mschap1,mschap2
[admin@dzeltenais_burkaans] /interface pptp-client> monitor 0 status: "connected" uptime: 7h24m18s idle-time: 6h21m4s encoding: "MPPE128 stateless" mtu: 1460 mru: 1460
This sub-menu shows interfaces for each connected PPTP clients. If interface is not explicitly added, it will appear as dynamic interface.
/interface pptp-server server