Manual:Interface/VLAN: Difference between revisions

From MikroTik Wiki
Jump to navigation Jump to search
(added link to more examples)
 
 
(7 intermediate revisions by 3 users not shown)
Line 29: Line 29:
<center>[[Image:image12003.gif]]</center>
<center>[[Image:image12003.gif]]</center>


{{ Note | The IEEE 802.1Q standard has reserved VLAN IDs with special use cases, the following VLAN IDs should not be used in generic VLAN setups: 0, 1, 4095 }}


==Q-in-Q==
==Q-in-Q==
Line 84: Line 85:
==Setup examples==
==Setup examples==


<br />
===Layer2 VLAN examples===
'''VLANs on Mikrotik environment are also described here:''' [http://wiki.mikrotik.com/wiki/Vlans_on_Mikrotik_environment VLANs with bridging] <br />
 
<br />
There are multiple possible configurations that you can use, but each configuration type is designed for a special set of devices since some configuration methods will give you the benefits of the built-in switch chip and gain larger throughput. Check the [[ Manual:Basic_VLAN_switching | Basic VLAN switching]] guide to see which configuration to use for each type of device to gain maximum possible throughput and compatibility, the guide shows how to setup a very basic VLAN trunk/access port configuration.
 
There are some other ways to setup VLAN tagging or VLAN switching, but the recommended way is to use [[ Manual:Interface/Bridge#Bridge_VLAN_Filtering | Bridge VLAN Filtering]]. Make sure you have not use any [[ Manual:Layer2_misconfiguration | known Layer2 misconfigurations]].
 
===Layer3 VLAN examples===


===Simple Example===
====Simple VLAN routing====


Lets assume that we have several MikroTik routers connected to a hub. Remember that a hub is an OSI physical layer device (if there is a hub between routers, then from L3 point of view it is the same as an Ethernet cable connection between them). For simplification assume that all routers are connected to the hub using ether1 interface and has assigned IP addresses as illustrated in figure below. Then on each of them the VLAN interface is created.
Lets assume that we have several MikroTik routers connected to a hub. Remember that a hub is an OSI physical layer device (if there is a hub between routers, then from L3 point of view it is the same as an Ethernet cable connection between them). For simplification assume that all routers are connected to the hub using ether1 interface and has assigned IP addresses as illustrated in figure below. Then on each of them the VLAN interface is created.
Line 182: Line 187:
</pre>
</pre>


===Create 'trunks' and implement routing between VLANs===
====InterVLAN routing====


If separate VLANs are implemented on a switch, then a router is required to provide communication between VLANs.
If separate VLANs are implemented on a switch, then a router is required to provide communication between VLANs.
Line 248: Line 253:
[[Category:VPN|V]]
[[Category:VPN|V]]
[[Category:Interface|V]]
[[Category:Interface|V]]
[[Category:Bridging and switching]]

Latest revision as of 07:58, 19 October 2018

Version.png

Applies to RouterOS: v3, v4+

Summary

Sub-menu: /interface vlan
Standards: IEEE 802.1Q

Virtual Local Area Network (VLAN) is a Layer 2 method that allows multiple Virtual LANs on a single physical interface (ethernet, wireless, etc.), giving the ability to segregate LANs efficiently.

You can use MikroTik RouterOS (as well as Cisco IOS, Linux and other router systems) to mark these packets as well as to accept and route marked ones.

As VLAN works on OSI Layer 2, it can be used just as any other network interface without any restrictions. VLAN successfully passes through regular Ethernet bridges.

You can also transport VLANs over wireless links and put multiple VLAN interfaces on a single wireless interface. Note that as VLAN is not a full tunnel protocol (i.e., it does not have additional fields to transport MAC addresses of sender and recipient), the same limitation applies to bridging over VLAN as to bridging plain wireless interfaces. In other words, while wireless clients may participate in VLANs put on wireless interfaces, it is not possible to have VLAN put on a wireless interface in station mode bridged with any other interface.

802.1Q

The most commonly used protocol for Virtual LANs (VLANs) is IEEE 802.1Q. It is a standardized encapsulation protocol that defines how to insert a four-byte VLAN identifier into Ethernet header. (see Figure 12.1.)

File:Image12001.gif

Each VLAN is treated as a separate subnet. It means that by default, a host in a specific VLAN cannot communicate with a host that is a member of another VLAN, although they are connected in the same switch. So if you want inter-VLAN communication you need a router. RouterOS supports up to 4095 VLAN interfaces, each with a unique VLAN ID, per interface. VLAN priorities may also be used and manipulated.

When the VLAN extends over more than one switch, the inter-switch link has to become a 'trunk', where packets are tagged to indicate which VLAN they belong to. A trunk carries the traffic of multiple VLANs; it is like a point-to-point link that carries tagged packets between switches or between a switch and router.

File:Image12003.gif
Icon-note.png

Note: The IEEE 802.1Q standard has reserved VLAN IDs with special use cases, the following VLAN IDs should not be used in generic VLAN setups: 0, 1, 4095


Q-in-Q

Original 802.1Q allows only one vlan header, Q-in-Q on the other hand allows two or more vlan headers. In RouterOS Q-in-Q can be configured by adding one vlan interface over another. Example:

/interface vlan
add name=vlan1 vlan-id=11 interface=ether1
add name=vlan2 vlan-id=12 interface=vlan1

If any packet is sent over 'vlan2' interface, two vlan tags will be added to ethernet header - '11' and '12'.

Properties

Property Description
arp (disabled | enabled | proxy-arp | reply-only; Default: enabled) Address Resolution Protocol mode
interface (name; Default: ) Name of physical interface on top of which VLAN will work
l2mtu (integer; Default: ) Layer2 MTU. For VLANS this value is not configurable. Read more>>
mtu (integer; Default: 1500) Layer3 Maximum transmission unit
name (string; Default: ) Interface name
use-service-tag (yes | no; Default: ) 802.1ad compatible Service Tag
vlan-id (integer: 4095; Default: 1) Virtual LAN identifier or tag that is used to distinguish VLANs. Must be equal for all computers that belong to the same VLAN.


Icon-note.png

Note: MTU should be set to 1500 bytes same as on Ethernet interfaces. But this may not work with some Ethernet cards that do not support receiving/transmitting of full size Ethernet packets with VLAN header added (1500 bytes data + 4 bytes VLAN header + 14 bytes Ethernet header). In this situation MTU 1496 can be used, but note that this will cause packet fragmentation if larger packets have to be sent over interface. At the same time remember that MTU 1496 may cause problems if path MTU discovery is not working properly between source and destination.


Setup examples

Layer2 VLAN examples

There are multiple possible configurations that you can use, but each configuration type is designed for a special set of devices since some configuration methods will give you the benefits of the built-in switch chip and gain larger throughput. Check the Basic VLAN switching guide to see which configuration to use for each type of device to gain maximum possible throughput and compatibility, the guide shows how to setup a very basic VLAN trunk/access port configuration.

There are some other ways to setup VLAN tagging or VLAN switching, but the recommended way is to use Bridge VLAN Filtering. Make sure you have not use any known Layer2 misconfigurations.

Layer3 VLAN examples

Simple VLAN routing

Lets assume that we have several MikroTik routers connected to a hub. Remember that a hub is an OSI physical layer device (if there is a hub between routers, then from L3 point of view it is the same as an Ethernet cable connection between them). For simplification assume that all routers are connected to the hub using ether1 interface and has assigned IP addresses as illustrated in figure below. Then on each of them the VLAN interface is created. File:Image12004.gif

Configuration for R2 and R4 is shown below:

R2:

[admin@MikroTik] /interface vlan> add name=VLAN2 vlan-id=2 interface=ether1 disabled=no

[admin@MikroTik] /interface vlan> print 
Flags: X - disabled, R - running, S - slave 
 #    NAME                  MTU   ARP        VLAN-ID INTERFACE                
0 R  VLAN2                 1500  enabled    2       ether1


R4:

[admin@MikroTik] /interface vlan> add name=VLAN2 vlan-id=2 interface=ether1 disabled=no

[admin@MikroTik] /interface vlan> print 
Flags: X - disabled, R - running, S - slave 
 #    NAME                  MTU   ARP        VLAN-ID INTERFACE                
0 R  VLAN2                 1500  enabled    2       ether1


The next step is to assign IP addresses to the VLAN interfaces.

R2:

 [admin@MikroTik] ip address> add address=10.10.10.3/24 interface=VLAN2
 [admin@MikroTik] ip address> print
 Flags: X - disabled, I - invalid, D - dynamic
   #   ADDRESS            NETWORK         BROADCAST       INTERFACE
   0   10.0.1.4/24        10.0.1.0        10.0.1.255      ether1
   1   10.20.0.1/24       10.20.0.0       10.20.0.255     pc1
   2   10.10.10.3/24      10.10.10.0      10.10.10.255    vlan2

 [admin@MikroTik] ip address>

R4:

 [admin@MikroTik] ip address> add address=10.10.10.5/24 interface=VLAN2
 [admin@MikroTik] ip address> print
 Flags: X - disabled, I - invalid, D - dynamic
   #   ADDRESS            NETWORK         BROADCAST       INTERFACE
   0   10.0.1.5/24        10.0.1.0        10.0.1.255      ether1
   1   10.30.0.1/24       10.30.0.0       10.30.0.255     pc2
   2   10.10.10.5/24      10.10.10.0      10.10.10.255    vlan2

[admin@MikroTik] ip address>


At this point it should be possible to ping router R4 from router R2 and vice versa:

 "Ping from R2 to R4:"

 [admin@MikroTik] ip address> /ping 10.10.10.5

 10.10.10.5 64 byte ping: ttl=255 time=4 ms

 10.10.10.5 64 byte ping: ttl=255 time=1 ms

 2 packets transmitted, 2 packets received, 0% packet loss

 round-trip min/avg/max = 1/2.5/4 ms


 "From R4 to R2:"
 
 [admin@MikroTik] ip address> /ping 10.10.10.3
 10.10.10.3 64 byte ping: ttl=255 time=6 ms
 10.10.10.3 64 byte ping: ttl=255 time=1 ms
 2 packets transmitted, 2 packets received, 0% packet loss
 round-trip min/avg/max = 1/3.5/6 ms

To make sure if VLAN setup is working properly, try to ping R1 from R2. If pings are timing out then VLANs are successfully isolated.

 
 "From R2 to R1:"

 [admin@MikroTik] ip address> /ping 10.10.10.2
 10.10.10.2 ping timeout
 10.10.10.2 ping timeout
 3 packets transmitted, 0 packets received, 100% packet loss

InterVLAN routing

If separate VLANs are implemented on a switch, then a router is required to provide communication between VLANs. Switch works at OSI layer 2 so it uses only Ethernet header to forward and does not check IP header. For this reason we must use the router that is working as a gateway for each VLAN. Without a router, a host is unable to communicate outside of its own VLAN. Routing process between VLANs described above is called inter-VLAN communication.

To illustrate inter-VLAN communication, we will create a trunk that will carry traffic from three VLANs (VLAN2 and VLAN3, VLAN4) across a single link between a Mikrotik router and a manageable switch that supports VLAN trunking. File:Image12005.gif

Each VLAN has its own separate subnet (broadcast domain) as we see in figure above:

  • VLAN 2 – 10.10.20.0/24;
  • VLAN 3 – 10.10.30.0/24;
  • VLAN 4 – 10.10.40.0./24.

VLAN configuration on most switches is straightforward, basically we need to define which ports are members of the VLANs and define a 'trunk' port that can carry tagged frames between the switch and the router.

"Configuration example on MikroTik router:"

"Create VLAN interfaces:"

/interface vlan
add name=VLAN2 vlan-id=2 interface=ether1 disabled=no
add name=VLAN3 vlan-id=3 interface=ether1 disabled=no
add name=VLAN4 vlan-id=4 interface=ether1 disabled=no

"Add IP addresses to VLANs:"

/ip address 
add address=10.10.20.1/24 interface=VLAN2
add address=10.10.30.1/24 interface=VLAN3
add address=10.10.40.1/24 interface=VLAN4

RouterOS /32 and IP unnumbered addresses

In RouterOS, to create a point-to-point tunnel with addresses you have to use address with a network mask of '/32' that effectively brings you the same features as some vendors unnumbered IP address.

There are 2 routers RouterA and RouterB where each is part of networks 10.22.0.0/24 and 10.23.0.0/24 respectively and to connect these routers using VLANs as a carrier with the following configuration:

Slash32.png

RouterA:

 /ip address add address=10.22.0.1/24 interface=ether1
 /interface vlan add interface=ether2 vlan-id=1 name=vlan1
 /ip address add address=10.22.0.1/32 interface=vlan1 network=10.23.0.1
 /ip route add gateway=10.23.0.1 dst-address=10.23.0.0/24

RouterB:

 /ip address add address=10.23.0.1/24 interface=ether1
 /interface vlan add interface=ether2 vlan-id=1 name=vlan1
 /ip address add address=10.23.0.1/32 interface=vlan1 network=10.22.0.1
 /ip route add gateway=10.22.0.1 dst-address=10.22.0.0/24


[ Top | Back to Content ]