Manual:Interface/W60G

From MikroTik Wiki
< Manual:Interface
Revision as of 10:40, 22 December 2017 by Normis (talk | contribs)
Jump to navigation Jump to search
Version.png

Applies to RouterOS: v6.41

Summary

Package: system

802.11ad implementation capable of providing Gigabit Ethernet speeds over wireless network.

Extend your Gigabit network over a transparent AES encrypted wireless 60GHz link without usual wired or wireless network problems.

General interface properties

Sub-menu: /interface w60g

Icon-warn.png

Warning: Devices comes in pre-configured, connected pairs. Manual configuration is optional


Property Description
arp (disabled | enabled | proxy-arp | reply-only; Default: enabled) Read more >>
arp-timeout (auto | integer; Default: auto) ARP timeout is time how long ARP record is kept in ARP table after no packets are received from IP. Value auto equals to the value of arp-timeout in /ip settings, default is 30s
comment (string; Default: ) Short description of the interface
disabled (yes | no; Default: yes) Whether interface is disabled
frequency (58320 | 60480 | 62640 | auto; Default: auto) Frequency used in communication (Only active on master device)
l2mtu (integer [0..65536]; Default: 1600) Layer2 Maximum transmission unit
mac-address (MAC; Default: ) MAC address of the radio interface
mode (master | slave | sniff; Default: master) Operation mode
mtu (integer [0..65536]; Default: 1500) Layer3 Maximum transmission unit
name (string; Default: wlan60-1) Name of the interface
password (string; Default: randomly generated) Password used for AES encryption
isolate-slaves (yes | no; Default: yes) Don't allow communication between connected clients (from RouterOS 6.41rc4)
put-slaves-in-bridge (; Default: ) Put newly created slave interfaces in this bridge (from RouterOS 6.41rc4)
ssid (string (0..32 chars); Default: value of System Identity) SSID (service set identifier) is a name that identifies wireless network

Slave interface properties

Icon-warn.png

Warning: Master device requires License level 4 (click for more information) to support more than one connected client


From RouterOS 6.41rc4 - Point To Multi Point experimental support is added.

There are several important changes and improvements in later versions

Connected clients are treated as individual interfaces, after successful connection new slave interface is created.

After update default configuration still works - newly created slave interface is moved to default bridge.

It is possible to apply different settings for each client: add them in different bridges, provide IP addresses from different subnets.


Property Description
parent (string; Default: wlan60-*) Parent interface name
put-in-bridge (none | parent | bridge-name; Default: parent) Add slave interface to specific bridge
remote-address (MAC; Default: matches master interface MAC) MAC address of master interface, slave is connecting to

Scan

Scan command searches for and displays available AP(s) in the frequency range supported by the W60G interface.

Using scan command the interface operation is disabled (wireless link is disconnected during the scan operation)

Currently it is impossible to do background scans.

Monitor

/interface w60g monitor wlan60-1

Monitor provides connection status, currently used frequency, remote device MAC address, MCS and signal quality percentage. It's preferable to run monitor for easy device set up and alignment.


Troubleshooting and Recommendations

Physical Properties

Atmospheric attenuation for the wireless frequencies used in 802.11ad standard is very high, this should be taken in account before deploying links.

The Wireless Wire kit have been tested in distances up to 200 meters. For stability and full speed availability this kit is recommended for distances up to 100 meters.

Devices are equipped with phase array 60° beamforming antennas, that can help signal find the way around objects in short distances but it's still vital to keep the line of sight clear on higher distances.

Configuration Reset For Wireless Wire

Reset button has same functionality as on other devices, explained in detail here

5 second button hold on startup (USR LED light starts flashing) - resets to password protected state.

10 second button hold on startup (USR LED turns solid after flashing) - completely removes configuration.

Icon-warn.png

Warning: After complete removal of configuration, only mac-telnet connection may be established