From MikroTik Wiki
Jump to navigation Jump to search

Applies to RouterOS: v6.41


Package: system,wireless

802.11ad implementation capable of providing Gigabit Ethernet speeds over wireless network.

Extend your Gigabit network over a transparent AES encrypted wireless 60GHz link without usual wired or wireless network problems.

General interface properties

Sub-menu: /interface w60g


Warning: Wireless Wire kit devices comes in pre-configured, connected pairs. Manual configuration is optional


Warning: In RouterOS versions older than 6.41 operating modes are called Master and Slave

Property Description
arp (disabled | enabled | proxy-arp | reply-only; Default: enabled) Read more >>
arp-timeout (auto | integer; Default: auto) ARP timeout is time how long ARP record is kept in ARP table after no packets are received from IP. Value auto equals to the value of arp-timeout in /ip settings, default is 30s
comment (string; Default: ) Short description of the interface
disabled (yes | no; Default: yes) Whether interface is disabled
frequency (58320 | 60480 | 62640 | auto; Default: auto) Frequency used in communication (Only active on master device)
l2mtu (integer [0..65536]; Default: 1600) Layer2 Maximum transmission unit
mac-address (MAC; Default: ) MAC address of the radio interface
mode (ap-bridge | bridge | sniff | station-bridge; Default: ap-bridge) Operation mode
mtu (integer [0..65536]; Default: 1500) Layer3 Maximum transmission unit
name (string; Default: wlan60-1) Name of the interface
password (string; Default: randomly generated) Password used for AES encryption
isolate-stations (yes | no; Default: yes) Don't allow communication between connected clients (from RouterOS 6.41)
put-stations-in-bridge (; Default: ) Put newly created slave interfaces in this bridge (from RouterOS 6.41)
ssid (string (0..32 chars); Default: value of System Identity) SSID (service set identifier) is a name that identifies wireless network

Station interface properties


Warning: Master device requires License level 4 (click for more information) to support more than one connected client

From RouterOS 6.41 - Point To Multi Point support is added.

There are several important changes and improvements in later versions. Please upgrade to latest version!

Connected clients are treated as individual interfaces, after successful connection new station interface is created.

After update default configuration still works - newly created station interface is moved to default bridge.

It is possible to apply different settings for each client: add them in different bridges, provide IP addresses from different subnets.

Sub-menu: /interface w60g station

Property Description
parent (string; Default: wlan60-*) Parent interface name
put-in-bridge (none | parent | bridge-name; Default: parent) Add slave interface to specific bridge
remote-address (MAC; Default: matches master interface MAC) MAC address of master interface, station is connecting to


Scan command searches for and displays available AP(s) in the frequency range supported by the W60G interface.

Using scan command the interface operation is disabled (wireless link is disconnected during the scan operation)

Currently it is impossible to do background scans.


/interface w60g monitor wlan60-1

Monitor provides connection status, currently used frequency, remote device MAC address, MCS and signal quality percentage. It's preferable to run monitor for easy device set up and alignment.

Point to Multi Point setup example

There are three different versions of wAP60G devices currently available:

  • Wireless Wire kit
  • wAP 60G
  • wAP 60G AP

Hardware wise devices are identical, but there are some limitations -

wAP 60G AP is designed for Access Point usage in PtMP (Point to Multi Point) setups, but can be also used as PtP (Point to Point) or as Station device. It's already equipped with level4 license for more than one connected client support More about Licenses

Wireless Wire kit and wAP60G devices comes with level3 license - license upgrade is needed to unlock more than one connected client in Access Point mode, but devices can connect to Access Points as regular Station devices.


Warning: Before configuration, make sure devices are running latest software versions: How to upgrade

Minimal configuration for transparent wireless link is matching SSID, and bridge containing Wireless and Ethernet interfaces.

In current example we will look at usage case where wAP60G AP is used as Access Point, wAP60G and Wireless Wire kit devices are used as Station devices, forming 4 unit network.


Warning: It's recommended to change IP addresses to avoid connection issues to the devices

wAP60G AP units come pre-configured with WISP Bridge default configuration

SSID and bridge between Wireless and Ethernet interfaces is already configured. It's recommended to set up Wireless password and change SSID. If device has been reset, You can also set correct mode and enable interface.

One liner that does all previously mentioned steps:

/interface w60g set wlan60-1 password="put_your_safe_password_here" ssid="put_your_new_ssid_here disabled=no mode=ap-bridge"

Wireless Wire and wAP60G units come pre-configured with PTP Bridge default configuration. Wireless Wire devices have already randomly generated matching SSID and Wireless password. Bridge device (Master or Access point device with one connected client support) needs Wireless mode change to station-bridge.

One liner that can be used to set devices in client mode:

/interface w60g set wlan60-1 password="put_your_safe_password_here" ssid="put_your_new_ssid_here" disabled=no mode=station-bridge

Troubleshooting and Recommendations

Physical Properties

Atmospheric attenuation for the wireless frequencies used in 802.11ad standard is very high, this should be taken in account before deploying links.

The Wireless Wire kit have been tested in distances up to 200 meters. For stability and full speed availability this kit is recommended for distances up to 100 meters.

Devices are equipped with phase array 60° beamforming antennas, that can help signal find the way around objects in short distances but it's still vital to keep the line of sight clear on higher distances.

SNMP OIDs for monitoring

From RouterOS>=6.42rc6 SNMP support for W60G interface monitoring is added

For main interfaces:  integer  Frequency  integer  MCS  integer  Signal quality  integer  tx-sector integer  rx-sector

station interfaces will be numbered forward starting from this point  integer  Frequency

Configuration Reset For Wireless Wire

Reset button has same functionality as on other devices, explained in detail here

5 second button hold on startup (USR LED light starts flashing) - resets to password protected state.

10 second button hold on startup (USR LED turns solid after flashing) - completely removes configuration.


Warning: After complete removal of configuration, only mac-telnet connection may be established