Manual:MPLS L2VPN vs Juniper

From MikroTik Wiki
Jump to navigation Jump to search

Summary

This article describes the basic setup of Point-to-Point L2VPN with Juniper J-series routers.

Configuration

Consider network setup as ilustrated below:

L2circuit-juniper.png

We will be setting up the layer 2 connection between the CE and PE routers as well as the MPLS and L2VPN between PE routers. The layer 2 link between the CE and PE routers will be an Ethernet VLAN circuit.


Set up VLANs

CE1 and CE2 routers:

/interface vlan
  add vlan-id=600 name=vlan1 disabled=no interface=ether1


PE1 (RouterOS):

No configuration currently is needed, later we will bridge VPLS tunnel.


PE2 (JunOS):

interfaces {
    fe-0/0/1 {
        vlan-tagging;
        encapsulation vlan-ccc;
        unit 1 {
            encapsulation vlan-ccc;
            vlan-id 600;
        }
    }
}

Set up IP connection, OSPF and LDP

CE1:

/ip address add address=192.168.88.1/24 interface=vlan1

CE2:

/ip address add address=192.168.88.2/24 interface=vlan1


PE1 (RouterOS):

/interface bridge 
  add name=loopback

/ip address
  add address=192.168.168.2/24 interface=ether3
  add address=10.255.11.31/32 interface=loopback

/routing ospf network
  add area=backbone disabled=no network=192.168.168.0/24
  add area=backbone disabled=no network=10.255.11.31/32

/mpls ldp
  set enabled=yes lsr-id=10.255.11.31 transport-address=10.255.11.31

/mpls ldp interface
  add interface=ether3

P (RouterOS):

/interface bridge 
  add name=loopback

/ip address
  add address=10.0.11.23/24 interface=ether1
  add address=192.168.168.1/24 interface=ether2
  add address=10.255.11.23/32 interface=loopback

/routing ospf network
  add area=backbone disabled=no network=10.0.11.0/24
  add area=backbone disabled=no network=192.168.168.0/24
  add area=backbone disabled=no network=10.255.11.23/32

/mpls ldp
  set enabled=yes lsr-id=10.255.11.23 transport-address=10.255.11.23

/mpls ldp interface
  add interface=ether1
  add interface=ether2


PE2 (JunOS):

interfaces {
    fe-0/0/0 {
        unit 0 {
            family inet {
                address 10.0.11.201/24;
            }
            family mpls;
        }
    }
    lo0 {
        unit 0 {
            family inet {
                address 10.255.11.201/32;
            }
        }
    }
}

protocols {
    mpls {
        interface fe-0/0/0.0;
        interface lo0.0;

    }

    ospf {
        export [ export-connected originate ];
        area 0.0.0.0 {
            interface fe-0/0/0.0;
            interface lo0.0 {
                passive;
            }
        }
    }
    ldp {
        egress-policy connected-only;
        transport-address 10.255.11.201;
        interface all;
    }
}

Finally we need to define policy options to advertise label binding for Loopback prefix:

policy-options {
    prefix-list loopback-prefix {
        10.255.11.201/32;
    }
    policy-statement connected-only {
        from {
            prefix-list loopback-prefix;
        }
        then accept;
    }
}

Set up L2VPN

PE1 (RouterOS):

/interface vpls
  add cisco-style=yes cisco-style-id=5 name=junos-l2circuit pw-type=tagged-ethernet \
    remote-peer=10.255.11.201

/interface bridge add name=vpn
/interface bridge port
  add interface=ether5 bridge=vpn
  add interface=junos-l2circuit bridge=vpn

PE2 (JunOS):

protocol {
    l2circuit {
        neighbor 10.255.11.31 {
            interface fe-0/0/1.1 {
                virtual-circuit-id 5;
            }
        }
    }
}

Verify Operation

Verify if LDP neighbors are found and forwarding table is created:

PE1:

[admin@10.0.11.31] /mpls ldp neighbor> print 
Flags: X - disabled, D - dynamic, O - operational, T - sending-targeted-hello, 
V - vpls 
 #      TRANSPORT       LOCAL-TRANSPORT PEER                       SEN
 0 DO   10.255.11.23    10.255.11.31    10.255.11.23:0             no 
 1 DOTV 10.255.11.201   10.255.11.31    10.255.11.201:0            yes
[admin@10.0.11.31] /mpls forwarding-table> print 
Flags: L - ldp, V - vpls, T - traffic-eng 
 #   IN-LABEL      OUT-LABELS  DESTINATION                    I NEXTHOP        
 0   expl-null    
 1 L 17            3396        10.255.11.201/32               e 192.168.168.1  
 2 L 19                        10.255.11.23/32                e 192.168.168.1  
 3 L 23            3390        10.5.101.0/24                  e 192.168.168.1  
 4 V 29                        junos-l2circuit        

PE2:

juniper@J4300> show ldp neighbor   
Address            Interface          Label space ID         Hold time
10.255.11.31       lo0.0              10.255.11.31:0           42
10.0.11.23         fe-0/0/0.0         10.255.11.23:0           13

See Also