Manual:Reset: Difference between revisions

From MikroTik Wiki
Jump to navigation Jump to search
m (Protected "Password reset" [edit=sysop:move=sysop])
No edit summary
(34 intermediate revisions by 8 users not shown)
Line 1: Line 1:
RouterOS password can only be reset by reinstalling the router, or using the reset jumper (or jumper hole) in case the hardware is RouterBOARD. For RouterBOARDS just close the jumper and boot the board until the configuration is cleared. For some RouterBOARDs there is not a jumper, but a jumper hole - just put a metal object into the hole, and boot the board.
__TOC__


{{ Note | RouterOS password can only be reset by reinstalling the router or using the reset button (or jumper hole) in case the hardware is RouterBOARD.
For X86 devices, only complete reinstall will clear the password, along with other configuration. For RouterBOARD devices, several methods exist, depending on our model. }}
== Reset from RouterOS ==
If you still have access to your router and want to recover its default configuration, then you can:
*) run the command '''"/system reset-configuration"''' from command line interface
*) do it from '''System -> Reset Configuration''' menu in the graphical user interface.
== Using reset button ==
RouterBOARD devices are fitted with a reset button which has several functions:
* '''Loading the backup RouterBOOT loader'''<br/>Hold this button before applying power, release after three seconds since powering, to load backup boot loader. This might be necessary if the device is not operating because of a failed RouterBOOT upgrade. When you have started the device with the backup loader, you can either set RouterOS to ''force backup loader'' in the RouterBOARD settings or have a chance to reinstall the failed RouterBOOT from a ".fwf" file  (total '''3 seconds''')
* '''Resetting the RouterOS configuration''' <br/>Hold this button until LED light starts flashing, release the button to reset RouterOS configuration to default.
* '''Enabling CAPs mode''' <br/>To connect this device to a wireless network managed by CAPsMAN, keep holding the button for 5 more seconds, LED turns solid, release now to turn on CAPs mode.
* '''Starting the RouterBOARD in Netinstall mode'''<br/>Or keep holding the button for 5 more seconds until LED turns off, then release it to make the RouterBOARD look for Netinstall servers. You can also simply keep the button pressed until the device shows up in the Netinstall program on Windows.
{{ Note | You can also do the previous three functions without loading the backup loader, simply push the button immediately after you apply power. You might need the assistance of another person to push the button and also plug the power supply at the same time}}
===How to reset configuration===
1) unplug the device from power
2) press and hold the button right after applying power
''Note: hold the button until LED will start flashing''
3) release the button to clear configuration.
{{Note | If you wait until LED stops flashing, and only then release the button - this will instead launch Netinstall mode, to reinstall RouterOS.}}
[[File:262 hi res.png]]
== Jumper hole reset ==
All RouterBOARD current models are also fitted with a reset jumper hole. Some devices might need opening of the enclosure, RB750/RB951/RB751 have the jumper hole under one of the rubber feet of the enclosure.
'''Using''': Close the jumper with a metal screwdriver, and boot the board until the configuration is cleared.


[[Image:Resethole.jpg]]
[[Image:Resethole.jpg]]
[[File:Passw.jpg]]
== Jumper reset for older models ==


The '''below''' image shows the location of the Reset Jumper on older RouterBOARDs like RB133C:
The '''below''' image shows the location of the Reset Jumper on older RouterBOARDs like RB133C:
Line 8: Line 55:
[[Image:CRW 5184.jpg]]
[[Image:CRW 5184.jpg]]


Note: Don't forget to remove the jumper after configuration has been reset, or it will be reset every time you reboot.
{{ Note | Don't forget to remove the jumper after the configuration has been reset, or it will be reset every time you reboot.}}


[[Category:RouterBOARD]]
[[Category:Routerboard|Passwordreset]]
[[Category:Manual]]
[[Category:Manual|Passwordreset]]

Revision as of 11:02, 5 May 2020

Icon-note.png

Note: RouterOS password can only be reset by reinstalling the router or using the reset button (or jumper hole) in case the hardware is RouterBOARD. For X86 devices, only complete reinstall will clear the password, along with other configuration. For RouterBOARD devices, several methods exist, depending on our model.


Reset from RouterOS

If you still have access to your router and want to recover its default configuration, then you can:

  • ) run the command "/system reset-configuration" from command line interface
  • ) do it from System -> Reset Configuration menu in the graphical user interface.

Using reset button

RouterBOARD devices are fitted with a reset button which has several functions:

  • Loading the backup RouterBOOT loader
    Hold this button before applying power, release after three seconds since powering, to load backup boot loader. This might be necessary if the device is not operating because of a failed RouterBOOT upgrade. When you have started the device with the backup loader, you can either set RouterOS to force backup loader in the RouterBOARD settings or have a chance to reinstall the failed RouterBOOT from a ".fwf" file (total 3 seconds)
  • Resetting the RouterOS configuration
    Hold this button until LED light starts flashing, release the button to reset RouterOS configuration to default.
  • Enabling CAPs mode
    To connect this device to a wireless network managed by CAPsMAN, keep holding the button for 5 more seconds, LED turns solid, release now to turn on CAPs mode.
  • Starting the RouterBOARD in Netinstall mode
    Or keep holding the button for 5 more seconds until LED turns off, then release it to make the RouterBOARD look for Netinstall servers. You can also simply keep the button pressed until the device shows up in the Netinstall program on Windows.
Icon-note.png

Note: You can also do the previous three functions without loading the backup loader, simply push the button immediately after you apply power. You might need the assistance of another person to push the button and also plug the power supply at the same time


How to reset configuration

1) unplug the device from power

2) press and hold the button right after applying power

Note: hold the button until LED will start flashing

3) release the button to clear configuration.

Icon-note.png

Note: If you wait until LED stops flashing, and only then release the button - this will instead launch Netinstall mode, to reinstall RouterOS.


262 hi res.png


Jumper hole reset

All RouterBOARD current models are also fitted with a reset jumper hole. Some devices might need opening of the enclosure, RB750/RB951/RB751 have the jumper hole under one of the rubber feet of the enclosure.

Using: Close the jumper with a metal screwdriver, and boot the board until the configuration is cleared.

Resethole.jpg

Passw.jpg

Jumper reset for older models

The below image shows the location of the Reset Jumper on older RouterBOARDs like RB133C:

CRW 5184.jpg

Icon-note.png

Note: Don't forget to remove the jumper after the configuration has been reset, or it will be reset every time you reboot.