RFC 1771 -> RFC 4271
Standards and Technologies:
- RFC 4271 Border Gateway Protocol 4
- RFC 4456 BGP Route Reflection
- RFC 1965 Autonomous System Confederations for BGP
- RFC 1997 BGP Communities Attribute
- RFC 2385 TCP MD5 Authentication for BGPv4
- RFC 3392 Capabilities Advertisement with BGP-4
- RFC 2918 Route Refresh Capability
- RFC 2858 Multiprotocol Extensions for BGP-4
- RFC 2545 Use of BGP-4 Multiprotocol Extensions for IPv6 Inter-Domain Routing
/routing bgp instance
|as (integer: 0..65535; Default: )||BGP autonomous system number|
|client-to-client-reflection (yes | no; Default: yes)||in case this instance is a route reflector: whether to redistribute routes learned from one routing reflection client to other clients|
|cluster-id (IP address; Default: )||in case this instance is a route reflector: cluster ID of the router reflector cluster this instance belongs to. This attribute helps to recognize routing updates that comes from another route reflector in this cluster and avoid routing information looping. Note that normally there is only one route reflector in a cluster; this case 'cluster-id' does not need to be configured and BGP router ID is used instead|
|confederation (integer: 0..65535; Default: )||in case of BGP confederations: autonomous system number that identifies the [local] confederation as a whole|
|confederation-peers (integer: 0..65535; Default: )||in case of BGP confederations: list of BGP peers internal to the [local] confederation|
|ignore-as-path-len (yes | no; Default: no)||whether to ignore AS_PATH attribute in BGP route selection algorithm|
|name (string; Default: "")||BGP instance name|
|out-filter (string; Default: "")||the output routing filter used by all BGP peers belonging to this instance|
|redistribute-connected (yes | no; Default: no)||if enabled, this BGP instance will redistribute the information about connected routes, i.e., routes to the networks that can be directly reached|
|redistribute-ospf (yes | no; Default: no)||if enabled, this BGP instance will redistribute the information about routes learned by OSPF|
|redistribute-other-bgp (yes | no; Default: no)||if enabled, this BGP instance will redistribute the information about routes learned by other BGP instances|
|redistribute-rip (yes | no; Default: no)||if enabled, this BGP instance will redistribute the information about routes learned by RIP|
|redistribute-static (yes | no; Default: no)||if enabled, the router will redistribute the information about static routes added to its routing database, i.e., routes that have been created using the '/ip route add' command on the router|
|router-id (IP address; Default: 0.0.0.0)||the BGP Router ID (for this instance). If not specified, BGP will use one of router's IP addresses.|
/routing bgp peer
|address-families (ip | ipv6 | l2vpn | vpnv4; Default: ip)||list of address families about which this peer will exchange routing information. The remote peer must support (they usually do) BGP capabilities optional parameter to negotiate any other families than IP|
|hold-time (time; Default: )|| specifies the BGP Hold Time value to use when negotiating with peers.
According to the BGP specification, if router does not receive successive KEEPALIVE and/or UPDATE and/or NOTIFICATION messages within the period specified in the Hold Time field of the OPEN message, then the BGP connection to the peer will be closed. The minimal hold-time value of both peers will be actually used (note that the special value 0 or 'infinity' is lower than any other values)
|in-filter (string; Default: "")||name of the routing filter that is applied to the incoming routing information|
|instance (string; Default: )||the instance this peer belongs to|
|interface (string | unspecified; Default: unspecified)||if specified, then outgoing connection will be made using only this interface; important if you want to run BGP using IPv6 link-local addresses|
|max-prefix-limit (integer; Default: )||maximum number of prefixes to accept from a specific peer. When this limit is exceeded, TCP connection between peers is tear down|
|max-prefix-restart-time (time 1 minute .. 10 days | infinity; Default: infinity)|| minimum time interval after which peers can reestablish BGP session.
|multihop (yes | no; Default: no)|| specifies whether the remote peer is more than one hop away.
This option affects outgoing nexthop selection as described in RFC 4271 (for EBGP only, excluding EBGP peers local to the confederation).
It also affects
|name (string; Default: )||the name of the peer|
|nexthop-choice (default | force-self | propagate; Default: default)|| Affects the outgoing NEXT_HOP attribute selection. Note that nexthops set in filters always takes precedence. Also note that nexthop is not changed on route reflection, expect when it's set in filter.
|out-filter (string; Default: "")||name of the routing filter that is applied to the incoming routing information|
|remote-address (IP address; Default: )||address of the remote peer|
|remote-as (integer: 0..65535; Default: )||AS number of the remote peer|
|route-reflect (yes | no; Default: no)||specifies whether this peer is route reflection client|
|tcp-md5-key (string; Default: "")||key used to authenticate the connection with TCP MD5 signature as described in RFC 2385|
|ttl (integer: 1..255 | default; Default: default)|| Time To Leave, the hop limit for TCP connection. For example, if 'ttl=1' then only single
hop neighbors will be able to establish the connection. This property only affects EBGP peers.
|update-source (IP address | interface name; Default: )|| If address is specified, this address is used as the source address of the outgoing TCP connection.
If interface name is specified, an address belonging to the interface is used as described.
Read only status properties:
|remote-id (IP address)||BGP router ID of the remote end|
|local-address (IP address)||local address used for TCP connection|
|uptime (time)||how long the connection has been in established state|
|prefix-count (integer)||number routing prefixes received from this peer currently in routing table|
|updates-sent (integer)||total number of reachable routing prefixes advertised|
|updates-received (integer)||total number of reachable routing prefixes received|
|withdrawn-sent (integer)||total number of withdrawn routing prefixes advertised|
|withdrawn-received (integer)||total number of withdrawn routing prefixes received|
|remote-hold-time (time)||hold time value offered by the remote end|
|used-hold-time (time)||negotiated hold time value|
|used-keepalive-time (time)||negotiated keepalive message interval (used-hold-time / 3)|
|state (idle | connect | active | opensent | openconfirm | established)||BGP protocol state|
/routing bgp advertisements
Read only information about outgoing routing information currently advertised.
This information is calculated dynamically after 'print' command is issued. As a result, it may not correspond to the information that at the exact moment has been sent out. Especially if in case of slow connection, routing information prepared for output will spend long time in buffers. 'advertisements print' will show as things should be, not as they are!
|prefix (IP prefix)||the NLRI prefix sent out|
|nexthop (IP address)||the NEXT_HOP attribute value sent out|
|as-path (string)||the AS_PATH attribute value sent out|
|origin (igp | egp | incomplete)||the ORIGIN attribute value sent out|
|local-pref (integer)||the LOCAL_PREF attribute value sent out|
|med (integer)||the MULTI_EXIT_DISC attribute value sent out|
|atomic-aggregate (yes | no)||the ATOMIC_AGGREGATE attribute value sent out|
|aggregator (IP address)||the AGGREGATOR attribute value sent out|
|originator-id (IP address)||the ORIGINATOR_ID attribute value sent out|
|cluster-list (string)||the CLUSTER_LIST attribute value sent out|
|peer (string)||the peer this information is advertised to|
/routing bgp network
BGP network configuration. BGP Networks is a list of IP prefixes to be advertised.
instance (name) - the instance this network belongs to network (IP prefix) - the aggregate prefix synchronize (yes | no; default: no) - install a route for this network only when there are some IGP routes falling under the range of this network
/routing bgp aggregate
BGP allows the aggregation of specific routes into one route with. This menu ('/routing bgp aggregate') allows to specify which routes you want to aggregate, and what attributes to use for the route created by aggregation.
advertise-filter (name; default: "") - name of the filter chain used to select the routes from which to inherit attributes attribute-filter (name; default: "") - name of the filter chain used to set the attributes of the aggregate route inherit-attributes (yes | no; default: yes) - whether to inherit BGP attributes from aggregated routes instance (name) - the instance this aggregate belongs to prefix (IP prefix) - the aggregate prefix summary-only (yes | no; default: yes) - whether to suppress advertisements of all routes that fall within the range of this aggregate suppress-filter (name; default: "") - name of the filter chain used to select the routes to be suppressed *status* routes-used (read-only: integer) - aggregated route statistics. in console: list of route console IDs used; in winbox: number of routes used. Notes: Terminology: aggregated routes - all routes, that fall within the range of this aggregate; they possibly are suppressed; aggregate route - route created by aggregation. Each aggregate will only affect routes coming from peers that belong to it's instance. 'suppress-filter' is useful only if 'summary-only=no'; 'advertise-filter' is useful only if 'inherit-attributes=yes' If result 'attribute-filter' match 'reject' or 'discard', the aggregate route is not created.
/routing bgp vpnv4-route