MikroTik SFP module compatibility table

This document clarifies compatibility between MikroTik made SFP modules and MikroTik RouterBOARD hardware.

Model	S-RJ01	S-85DLC05D	S-31DLC20D	S-3553LC20D	S+85DLC03D	S+31DLC10D	S+2332LC10D	SFP+ 1m/3m DAC
CCR1072-1G-8S+	+	+	+	+	+	+	+	+
CCR1036-12G-4S	+	+	+	+	+	+	+	+
CCR1036-8G-2S+	+	+	+	+	+	+	+	+
CCR1016-12S-1S+	+ *	+ *	+ *	+ *	+	+	+	+
CCR1009-8G-1S-1S+	+ *	+	+	+	+	+	+	+
CRS125-24G-1S	+	+	+	+	+	+	+	+
CRS226-24G-2S+	-	+ *	+ *	+ *	+	+	+
CRS212-1G-10S-1S+	+ *	+ *	+ *	+ *	+	+	+	+
CRS210-8G-2S+	-	+ *	+ *	+ *	+	+	+	+
CRS112-8G-4S	+	+	+	+	+	+	+	+
CRS109-8G-1S	+	+	+	+	+	+	+	+
RB260GS	+	+	+	+	+	+	+	+
RB2011	+	+	+	+	+	+	+	+
RB922/921	+	+	+	+	+	+	+	+
RB953GS	+	+	+	+	+	+	+	+
FTC	+	+	+	+	+	+	+	+

Legend:
Color codes:	Not supported	Check notes below

• NOTES:
  • CCR1009-8G-1S-1S+ -- SFP+1 interface does not support rj45 SFP modules. SFP1 interface however will work just fine with this type of transceiver.
  • CCR1016-12S-1S+ / CRS212-1G-10S-1S+ -- SFP+1 interface does not work on any other link speed than 10G (does not support 1.25G fiber optic transceivers)
  • CRS226 / CRS210 -- Only SFP+1 interface supports SFP 1.25G fiber optic transceivers, SFP+2 works only with 10G transceivers/links.

S-RJ01

Table that states in what link rates if mounted in specific MikroTik devices S-RJ01 module will be able to work.

Model	1000	100	10
RB922	+	+	+
RB921	+	+	+
RB953	+/+	+/-	+/-
RB2011	+	-	-
FTC	+	-	-
CRS112	+	+	+
CRS125/CRS109	+	+	+
CRS212	+	+	+
CRS226/CRS210	-	-	-
CCR1009	+/+	+/+	+/+
CCR1016-12S-1S+	+	+	+
CCR1036-12G-4S	+	+	+
CCR1036-8G-2S+	+	+	+
CCR1072-1G-8S+	+	+	+

Notes:

• Rate works fine: +
• Rate does not work: -

• RB953: SFP2/SFP1
• CCR1009: SFP+/SFP

Note: All results taken from test scenarios where SFP or SFPplus interface is configured in auto-negation enabled and devices version no lower than RouterOS v6.32