View source for Mikrotik and Telekom Malaysia UniFi Setup Using QuickSet - by arpee/soonwai

== Introduction ==
This guide is for beginners to Mikrotik who are looking to setup their router for TM UniFi in Malaysia. Mikrotik RouterOS may look daunting to a newcomer but it's actually quite easy for a basic setup. Look here for the [http://forum.mikrotik.com/viewtopic.php?f=13&t=118566 forum discussion thread.]

Before we begin, here is some information on UniFi. Some of it is technical but don't worry about it if you don't know what a VLAN is.
* [http://unifi.my UniFi] is a FTTH service by [http://www.tm.com.my Telekom Malaysia (TM)] in the country of Malaysia. It delivers triple-play services via fibre or xDSL.
* It bears no relation to Ubiquiti.
* Authentication is by PPPoE username and password.
* Triple-play services are delivered via VLANs.
* VLAN id 500 for Internet.
* VLAN id 600 for HyppTV (IPTV).
* VLAN id 400 for VOIP.
* This guide is specific to UniFi but if your ISP uses a similar system (PPPoE and VLANs), the steps are kinda similar.

== Step-by-Step Configuration - Internet ==
So let's start. We will configure the Internet first. Get the following ready:
* Your '''UniFi username''' which looks like ''myname@unifi'' or ''myname@unifibiz'' for business accounts. 
* Your '''UniFi password''' which, if generated by TM, is usually a case sensitive 13 character alphamumeric string.
* The TM supplied UniFi BTU or Broadband Termination Unit which could be an optical network terminal (ONT) or a xDSL modem.
* A Mikrotik router.

To configure the router, we use either:
* '''winbox''' which is a Windows app. I'll be using this for the guide. Get it from http://www.mikrotik.com/download
* or any modern web browser.

=== Default Configuration ===
One more thing before we start. This guide presumes a router with an out-of-the-box default configuration. This is very important so that we start on the same page and not get confused. If it's not, please reset the router to its default configuration before starting.

See [[Manual:Configuration_Management#Configuration_Reset]] or [[Manual:Reset]] on how to reset your router.

=== Connect the Cables ===
* Connect a cable from Ethernet '''Port 1''' of the BTU to Ethernet '''Port 1''' of the Mikrotik router. The port numbers are important.
* Connect a computer to Ethernet '''Port 2''' of the router.
* Ensure that your computer is set to acquire an IP address automatically.

=== Login to the Mikrotik Router ===
Login to the router using either winbox or a web browser. Using a web browser looks similar. I think you'll figure it out.

Login to the Mikrotik router with the following:
* Default IP address: 192.168.88.1
* Username: admin
* Password: (no password)

=== Quick Set ===
We'll use Quick Set to get a headstart on the configuration.

[[File:TMUnifi01.jpg]]

# Click on Quick Set.


[[File:TMUnifi02.jpg]]

'''Set as Home AP and enter UniFi username & password'''
# Select Home AP.
# Select PPPoE.
# Enter UniFi username and password.
# OK
{{Note | While you're here, also set your wifi to a cooler name and give it a password. }}

=== VLAN 500 ===
[[File:TMUnifi03.jpg]]

# Click Interfaces
# Click VLAN
# Create a new VLAN
# Give it a name e.g.: vlan500
# Set VLAN ID: 500
# Ensure Interface is: ether1-gateway
# OK

=== PPPoE ===
[[File:TMUnifi03.jpg]]

# Click PPP
# Double-click pppoe-out1
# Set Interfaces to vlan500
# OK

That's it.

Internet should be working now.

== Step-by-Step Configuration - HyppTV ==
Next we'll setup HyppTV.

For HyppTV we'll be using Ethernet '''Port 5'''. So connect your HyppTV Set Top Box (STB) to this port.

=== Ethernet Port 5 ===
[[File:TMUnifi05.jpg]]

# Click Interfaces
# Double click ether5-slave-local
# Change Master Port to: none 
# OK

=== VLAN 600 ===
[[File:TMUnifi06.jpg]]

# Click Interfaces
# Click VLAN
# Create a new VLAN
# Give it a name e.g.: vlan600iptv
# Set VLAN ID: 600
# Ensure Interface is: ether1-gateway
# OK

=== Bridge ===
[[File:TMUnifi07.jpg]]

# Click Bridge
# Create a new Bridge
# Give it a name e.g.: unifi.iptv
# OK

=== Bridge Ports ===
[[File:TMUnifi08.jpg]]

# Click Bridge
# Click Ports
# Add a port
# Set Interface to: ether5-slave-local
# Set Bridge to: unifi.iptv (that's the bridge that you just created above)
# Add another port
# Set Interface to: vlan600iptv
# Set Bridge to: unifi.iptv
# OK

And that's it. Remember to plug your HyppTV Set Top Box (STB) into Ethernet Port 5. Switch on your HyppTV STB and enjoy.

== Other ISPs ==
=== Maxis ===
* BTU Ethernet Port 2
* Internet VLAN 621
* Astro IPTV not supported
=== Ohana ===
* BTU Ethernet Port 2
* Internet VLAN 624
=== Others ===
TBD
== We're Done! ==
That's all there is to it. If you have any questions or suggestions, please post to this [http://forum.mikrotik.com/viewtopic.php?f=13&t=118566 thread] in the Mikrotik forums. My forum username is soonwai. My wiki username is arpee.