Manual:System/Resource
Applies to RouterOS: v3, v4 +
Summary
General
Sub-menu level: /system resource
General resource menu shows overall resource usage and router statistics like uptime, memory usage, disk usage, version etc.
It also has several sub-menus for more detailed hardware statistics like PCI, IRQ and USB.
[admin@RB1100test] /system resource> print
uptime: 2w1d23h34m57s
version: "5.0rc1"
free-memory: 385272KiB
total-memory: 516708KiB
cpu: "e500v2"
cpu-count: 1
cpu-frequency: 799MHz
cpu-load: 9%
free-hdd-space: 466328KiB
total-hdd-space: 520192KiB
write-sect-since-reboot: 1411
write-sect-total: 70625
bad-blocks: 0.2%
architecture-name: "powerpc"
board-name: "RB1100"
platform: "MikroTik"
Properties
All properties are read-only
| Property | Description |
|---|---|
| architecture-name (string) | CPU architecture. Can be powerpc, x86, mipsbe or mipsle. |
| bad-blocks (percent) | Shows percentage of bad blocks on the NAND. |
| board-name (string) | RouterBOARD model name |
| cpu (string) | Cpu model that is on the board. |
| cpu-count (integer) | Number of CPUs present on the system. Each core is separate CPU, Intel HT is also separate CPU. |
| cpu-frequency (string) | Current CPU frequency. |
| cpu-load (percent) | Percentage of used CPU resources. Combines all CPUs. Per-core CPU usage can be see in CPU submenu |
| free-hdd-space (string) | Free space on hard drive or NAND |
| free-memory (string) | Unused amount of RAM |
| platform (string) | Platform name, usually it is "MikroTik" |
| total-hdd-space (string) | Size of the hard drive or NAND |
| total-memory (string) | Amount of installed RAM |
| uptime (time) | Time interval passed since boot-up. |
| version (string) | Installed RouterOS version number. |
| write-sect-since-reboot (integer) | Number of sector writes in HDD or nand since router was last time rebooted. |
| write-sect-total (integer) | Number of sector writes in total. |
CPU
Sub-menu level: /system resource cpu
This submenu shows per-cpu usage, as long as IRQ and Disk usage.
[admin@RB1100test] /system resource cpu> print CPU LOAD IRQ DISK 0 5% 0% 0% [admin@RB1100test] /system resource cpu>
Properties
Read-only properties
| Property | Description |
|---|---|
| cpu (integer) | Identification number of CPU which usage is shown. |
| load (percent) | CPU usage in percents |
| irq (percent) | IRQ usage in percents |
| disk (percent) | Disk usage in percents |
IRQ
Sub-menu level: /system resource irq
Menu shows all used IRQs on the router. It is possible to set up IRQ load balancing on mulicore systems by assigning IRQ to specific core.
IRQ assignments are done by hardware and cannot be changed from RouterOS. For example, if all Ethernets are assigned to one IRQ, then you have to deal with hardware: upgrade motherboards BIOS, reassign IRQs manually in BIOS, if none of above helps then change the hardware.
Properties
| Property | Description |
|---|---|
| cpu (auto | integer; Default: ) | Specifies which CPU is assigned to the IRQ.
|
Read-only properties
| Property | Description |
|---|---|
| active-cpu (integer) | Shows active CPU in multicore systems. |
| count (integer) | Number of interrupts. On ethernet interfaces interrupt=packet. |
| irq (integer) | IRQ identification number |
| users (string) | Process assigned to IRQ |
IRQ Load Balancing
USB
Sub-menu level: /system resource usb
This menu displays all available USB controllers on the board. Menu is available only if at least one USB controller is present.
[admin@MikroTik] /system resource usb> print detail 0 device="2:1" name="RB400 EHCI" serial-number="rb400_usb" vendor-id="0x1d6b" device-id="0x0002" speed="480 Mbps" ports=2 usb-version="2.00" 1 device="1:1" name="RB400 OHCI" serial-number="rb400_usb" vendor-id="0x1d6b" device-id="0x0001" speed="12 Mbps" ports=2 usb-version="1.10"
Properties
| Property | Description |
|---|---|
| device (string) | |
| device-id (hex) | Hexadecimal device ID |
| name (string) | Descriptive name of the device retrieved from driver |
| ports (integer) | How many ports are supported by usb controller |
| serial-number (string) | |
| speed (string) | Max USB speed that can be used (480Mbps for USBv2 and 12Mbps for USBv1) |
| usb-version (string) | Identifies max spported USB version |
| vendor (string) | Device manufacturer's name. |
| vendor-id (hex) | Hexadecimal vendor ID |
PCI
Sub-menu level: /system resource pci
PCI submenu shows the information about all PCI devices on the board
[admin@RB1100test] /system resource pci> print # DEVICE VENDOR NAME IRQ 0 06:00.0 Attansic Technology Corp. unknown device (rev: 192) 18 1 05:00.0 Freescale Semiconductor Inc MPC8544 (rev: 17) 0 2 04:00.0 Attansic Technology Corp. unknown device (rev: 192) 17 3 03:00.0 Freescale Semiconductor Inc MPC8544 (rev: 17) 0 4 02:00.0 Attansic Technology Corp. unknown device (rev: 192) 16 5 01:00.0 Freescale Semiconductor Inc MPC8544 (rev: 17) 0 6 00:00.0 Freescale Semiconductor Inc MPC8544 (rev: 17) 0
Properties
All properties are read-only
| Property | Description |
|---|---|
| category (string) | PCI device type, for example ethernet controller |
| device (string) | |
| device-id (hex) | Hexadecimal device ID |
| io (hex-hex) | I/O memory range |
| irq (integer) | IRQ asigned to the device |
| memory (hex-hex) | Memory range |
| name (string) | Descriptive name of the device retrieved from driver |
| vendor (string) | Device manufacturer's name. |
| vendor-id (hex) | Hexadecimal vendor ID |