Supported Hardware

This page should be edited by the user community to reflect their tested hardware and version used.

See also: Device driver list in manual

Terminals

Vendor	Model	ROS version	Result
HP	t5510	> 5.x	Works OK. Boot from CF card connected to PATA (small, notebook). USB, COM and ethernet works. In routing ~40 Mb/s. PCI not tested, but should works.

Motherboards

Vendor	Model	ROS version	Result
Asrock	Intel 82801G chipset	3.0-3.14	Bad performance, locks up under heavy load, supports multi cpu, PATA not supported, integrated ethernet not recognized. Maybe it's just Asrock bad motherboard don't know if the problem is in intel 82801G chipset tested on 2 motherboards, never tested on 2.9.x
ASUS	P8H67-V (Intel® H67(B3), 3xPCI, 4xPCI-E)	5.XX	Don't work. "Kernel Panic". Mikrotik has not driver compatibility with this motherboard.
ASUS	P5B-Deluxe (Intel P965, 3xPCI, 3xPCI-E)	3.13	Works fine on Intel Core 2 Duo E6400. Not supported PATA controller. Both integrated Gigabit NIC (Marvell Yukon 88E8056 & 88E8001) works fine but only at 100Mbps.
ASUS	P5B-V (Intel P965, 3xPCI, 4xPCI-E)	3.13	Works fine on Intel Dual Core E2180. Not supported PATA controller. Integrated Gigabit NIC Marvell Yukon 88E8001 works fine but only at 100Mbps. Winbox via MAC = problem, disconnects after 3 seconds. Winbox via IP no problem.
ASUS	P5KC (Intel P35, 3x PCI, 3xPCI-E)	3.10	Not supported PATA controller (JMicron JMB363), ROS can boot from USB flash drive; internal ethernet not recognized.
ASUS	P5GC-MX/1333 (2x PCI)	3.7	Works great for pentium dual-core e2160, hdd pata and sata, 1,5gb ram dual channel mode, except the attansic l2 ethernet onboard card is not recognized.
ASUS	P5GC (6xPCI)	2.9.39	Ethernet recognized but not working
ASUS	P7P55D PRO	4.5	Works ok, PATA controller (JMicron JM363) and internal Ethernet successfully recognized.
ASUS	P6T SE	4.0	RouterOS boots and works with SATA disk set to 'IDE compatibility mode'.
ASUS	A7V133-C	3.0 beta 7	Works fine
ASUS	A7V600-X	3.25	Works fine
EPoX	EP-4VKMI	3.16 - 3.24	Works fine.
EPoX	8RDA+	3.6	Work fine including integrated ethernet
Intel	D815EGEW	2.9.x	Excellent performance under 2.9. Not tested under v3. Onboard Ethernet Works perfectly.
Intel	D845GVSRL	3.7, 3.1, 2.9	Very Stable, used for 4 years
Intel	D945GCCRL	2.9.43 & 3.0 beta 5	Ethernet & DoM not recognized
Intel	D945GCLF2	3.23	4 core's, 2gb ram, 32gb ssd, no problems.
Intel	D945GCPE	3.0 beta 9	Work fine including integrated ethernet
Intel	D945GCNL	3.11	Works fine but integrated ethernet (just disable) goes up and down on reboots multi-cpu= yes. shared IRQ for PCI devices, decrease nic performace.
Intel	D945GNT	2.9.45	Works fine
Intel	DG33FB	3.7	Works fine, Ethernet but not working (IRQ 9), set in BIOS Security/XD Tegnology to disable
Intel	DG950	2.9.42	Ethernet not recognized
Intel	DG965SWH	3.0 beta 9	Works fine, but only with SATA not IDE
Intel	DH67BLB3	5.14	Works Great with i7-2600k processor
Intel	DP55WG	4.6	multi-cpu smp works great, onboard NIC not supported by RouterOS 4.6 yet though, must use pci/pci express nics
Intel	DQ965GFEKR (D41676)	3.7, 3.4	Works fine on 3.7/3.4 if multi-cpu=no, BUT 3.5-3.7 fail to boot with E4600 processor and multi-cpu=yes
Intel	S3210SHLC	4.2	Boot from USB stick. Work fine for my PPPoE server. Up to 1300 users with summary 200Mbit traffic.
Intel	D945GZT-M	3.0rc4	Works fine
Chaintech	AADF950	3.0 beta 5	Works fine
Abit	KT7E	3.0 beta 7	Works fine
ECS	nForce3-A	3.6	Work fine including integrated ethernet
ECS	P4M800PRO-M478	2.9.43	No Apparent Problems, Disabled any unneeded devices in the BIOS
Abit	BE6	2.9.43	Works
VIA	EPIA-MII12000	2.9.42	Locks up under heavy load across wireless
Supermicro	5015M-MR	2.9.28	Motherboard is PDSMi w dual core
Supermicro	PDSBM-LN2+	2.9.51 & 3.16	http://forum.mikrotik.com/viewtopic.php?f=1&t=28184
Supermicro	PDSMi-LN4+	2.9.51, 3.13, 3.20	Very stable even with dual-cores enabled.
Gigabyte	GA-41M-ES2L	3.28	Works fine; CPU Intel Core2 Dual 2.7GHz; 2XRB44GV
Gigabyte	GA-6BXS	2.9.43	Works fine
Gigabyte	GA-8I848P-G	3.6	Work fine including integrated ethernet
Gigabyte	GA-8ST667 rev. 3.0	3.13	Works fine; CPU Intel Celeron 2,4GHz; Chipset SiS 645DX; 5xPCI;
Gigabyte	GA-M720-US3 rev 1.0	4.6	Works fine (downvolted to 1.1V)
Gigabyte	GA-MA790GP-UD4H	3.30	Works fine
Gigabyte	K8-NS-ULTRA	2.9.x-3.7	Excelent work, including both onboard ethernet (100 and 1000 lan)
Gigabyte	GA-MA770-DS3 (rev. 2.0)	3.10	Works fine and extreme stable include onboard LAN, IDE DOM can load normally
	Chipset P35 (Tested Using Gigabyte GA-P35-DS3L & Abit IP35)	3.7	Work fine but only with SATA, not IDE (Include DOM), bellow v3.7 problem with SATA too
Microsoft	Virtual PC 2007	3.7	Installs and and tries to boot.
VMware	Workstation v6.0.3	3.7	Runs Wicked Fast! I have had up to 8 Ethernet interfaces running simultaneously.
VMware	ESXi v4	3.30	Select IDE type for virtual disk - works perfectly!
	Xen 3.2.1 on Intel C2Q	4.x	Installs and runs fine on HVM bootloader using Intel VT technology. Even switches to RouterOS console from Dom0 shell. Ethernet interfaces work perfectly. Do not install xen/kvm RouterOS packages!
DFI	AD73 Pro (Chipset VIA KT266A/VT8233ACD)	2.9.x-3.30	Works fine. All 5 PCI's ocupied with 1 x LAN and 6 x R52H's (3 in RouterBoard11 and 3 in RouterBoard14!)
DFI	AK75-EC (Chipset VIA KT133A/686B)	3.14-3.30	Stable. All PCI's ocupied with LAN, miniPCI-PCI adapters fitted with R5H/R52H's and XR5's
Fujitsu Siemens	Primergy RX100S5	3.1, 3.7, 3.22	Can Install from Netinstall with RAID (LSI) Controller enable. Can't install from CD and Netinstall with only SATA or PATA mode. But NOT RUN
MSI	785GM-E51	4.11	Works fine, booted from USB stick, integrated LAN working

Ethernet chipsets

The lists contain most common ethernet chipset drivers from the Linux kernel.

RouterOS version 5 (Linux 2.6.35):

• e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k6-NAPI
• e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k4
• igb: Intel(R) Gigabit Ethernet Network Driver - version 2.1.0-k2
• bnx2: Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v2.0.15 (May 4, 2010)
• tg3: c:v3.110 (April 9, 2010)
• atl1c: version 1.0.0.2-NAPI
• r8169: Gigabit Ethernet driver 2.3LK-NAPI
• sky2: driver version 1.28

RouterOS version 6 (Linux 3.3.5):

• e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
• e1000e: Intel(R) PRO/1000 Network Driver - 1.5.1-k
• igb: Intel(R) Gigabit Ethernet Network Driver - version 3.2.10-k
• bnx2: Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v2.2.1 (Dec 18, 2011)
• tg3: c:v3.122 (December 7, 2011)
• atl1c: version 1.0.0.2-NAPI
• r8169: Gigabit Ethernet driver 2.3LK-NAPI
• sky2: driver version 1.30

Vendor	Model	ROS version	Result
3Com	3c905B Cyclone 100BaseTX	2.9.51	Works! Extremely reliable, doesn't fully support tagged vlans
3Com	3cSOHO100-TX [Hurricane] (rev: 48)	3.14rc1	Works
3Com	3c905C-TX/TX-M [Tornado] (rev: 120)	2.9.51	Works! Extremely reliable, doesn't fully support tagged vlans
3Com	3c905C-TX/TX-M [Tornado] (rev: 116)	2.9.51	Works! Extremely reliable, doesn't fully support tagged vlans
3Com	3c905B-FX Fast Etherlink XL FX 100baseFx [Cyclone] (rev: 0)	2.9.43	Works but no link in Winbox and no Graph in Dude !!!!
Adaptec	ANA-6944A/TX Quad 10/100MBit	>=3.20	Works
Broadcom	BCM5715	v5 / v6	v5 - Works like a charm. v6 - Possible problems with traffic (loss/drops), due to driver version.
Compaq	NC3122 Fast Ethernet Server Adapter	3.30	recognized but not working
Intel	S82557 10/100MBit	2.9.43	works
Intel	PWLA8391GT PRO1000/GT	3.7, 3.1, 2.9	Extremely Stable, used for years
Intel	PWLA8391GTL PRO1000/GT	3.4	Extremely Stable, used for years
Intel	82575EB & 8257GB	3.15	Added support
Intel	82576 Gigabit ET Quad port	4.5	Not recognized
Intel	82576 Gigabit Dual Port (e1g42et)	5.8	Works
Intel	82572EI (EXPI9300PTBLK)	4.5, 4.6	Works
Intel	82572GI (EXPI9400PTBLK)	4.5, 5.14	Works
Intel	82574L (EXPI9301CT)	5.14	Supported in ROS 5 / Works
Intel	82571EB (EXPI9404PT) QUAD COPPER	4.6, 5.14	Works
Intel	S82557/S82555 10/100 Mbit TX	2.9.50 / 3.16	Works Stable! FCC ID:EJMNPDSPD035
Intel	PRO 1000 MT	2.9.51	Works
Intel	82541GI/PI Gigabit Ethernet Controller (rev: 5)	2.9.49	Working but with high traffic (>100M) and many packets makes drops
Intel	10Gbit Ethernet PCI Express	3.17	Works
Intel	82557/8/9 Ethernet Pro 100 (rev: 5)/Dual ports(Two ports/2-port)/RJ-45"	4.10	Works, fine!
Intel	82599ES - Intel X520 series adapters	5.x & 6.x	Works, fine! Note: has SFP transceiver vendor restrictions: http://www.intel.com/support/network/adapter/pro100/sb/CS-030612.htm
D-Link	DFE-528TX rev. E1	3.13	Works
D-Link	DFE-580TX 4-port	3.0 beta 5	Bad card, not recommended. Hangs router
D-Link	DFE-530/538TX	2.9.43 - 3.x	Works well, no apparent problems.
D-Link	DUB-E100 USB	3.18	added support, reported to be working
Marvell	88E8001 Gigabit Ethernet Controller (rev: 20)	3.13	Works
Marvell	88E8056	3.6	reported to be working with some BIOS setting enabled
DECchip	21143 (ZYNX ZX410 4-port cPCI)	2.9.51	Working
Realtek	RTL-8169 Gigabit Ethernet x4 (rev: 16)	3.0-3.11	Working Extremely reliable, used 4 mounts
Realtek	RTL8111 (10/100/1000Mbit)	3.10	Seems to be working only in older RouterOS v3 releases, v3.10 and before.
Realtek	RTL8111C, RTL8111DL (10/100/1000Mbit)	4.6 - 4.11	Working
Realtek	RTL8139C+	3.14	Works
Realtek	RTL8139D	3.x	Some work, others don't. Check for yourself.
Realtek	RTL-8139/8139C/8139C+ (rev: 16)	4.9 & 4.10	Works, fine!
Realtek	RTL-8029(AS) (rev: 0)"	4.9 & 4.10	Works, fine!
StarTech	ST10000SPEX4 - 4 Port PCIe Gigabit Ethernet Network Card	6.7	Works, great!
ZNYX	ZX346Q	3.27	Works
VIA	VT6102 [Rhine-II] (rev: 67)"	4.9 & 4.10	Works, fine!
Silicon Integrated Systems [SiS]	191 Gigabit Ethernet Adapter (rev: 2)	6.28	Works, fine!

x86 Systems

Model	ROS version	Result
Dell Optiplex GX1	2.9.x-3.0	Intel onboard/cpu 450-600Mhz, eth:3com, best for wirless stations; uptime over 200d, no problems at all.
Compaq Presario 2282	2.9.43	With 3c905 [Boomerang], no apparent problems
Dell GX100	2.9.x - 3.7	Intel onboard, 2 free pci, Intel cpu
Dell GX240	2.9.x - 3.7	Intel onboard, 2 free pci, Intel cpu, IDE HDD.
Dell GX260	2.9.x - 3.7	Intel onboard, 2 free pci, Intel cpu, IDE HDD.
Dell GX270	2.9.x - 3.7	Intel onboard, 2 free pci, Intel cpu. IDE HDD.
Dell GX280	2.9.x - 3.7	Intel onboard, 2 free pci, Intel cpu, SATA HDD.
Dell Dimension XPS GEN 3	2.9.x	Lan Onboard, 4 free pci, Intel cpu , SATA HDD ( Excellent Stability )
Dell Inspiron Desktop 518	2.9.x - 3.7	After netinsall stuck on "loading system"
Dell PowerEdge 860	3.x	1U Rackmount, 2x Broadcom Gigabit onboard, 1x Intel CPU (many options), 1 PCI/1 PCIe or 2 PCIe riser options, SATA HDD ONLY. (some issues with floppy netinstall)
Dell PowerEdge R200	>= 3.19 recommended	Severe stability and clock issues with non-current ROS. Works like a top on 3.19 though. Also, if using an SATA-to-CF converter, the license key for the CF card in an R200 will only transfer to other R200's without Mikrotik reissuing it.
Dell PowerEdge R210	5.1 - 5.6	1U Rackmount. Half-depth (39cm) chassis. Dual port on-board Broadcom 5716 Gigabit Ethernet controllers. Single CPU on Intel 3420 Motherboard Chipset. Works OK and stable, once installed. Some issues with NetInstall - PXE boot works OK but install can't continue (says waiting for drivers...). Tested with Intel Gigabit ET Quad Port Server Adapter - works perfectly. - With Processador Intel E3-1220 and Broadcom NetXtreme II 5709 Gigabit NIC w/TOE & iSOE,Quad Port, Copper, PCIe-4 works fine.
Dell PowerEdge R310	5.0rc7	1U Rackmount. 2 x on-board Broadcom 5716 Gigabit Ethernet controllers. Single CPU on Intel 3420 Motherboard Chipset. Works OK and stable, once installed. Some issues with NetInstall - PXE boot works OK but install can't continue (says waiting for drivers...). Tested with Intel Gigabit ET Quad Port Server Adapter - works perfectly.
Dell PowerEdge 2950	3.x	2U Rackmount, Optional Redundant Power Supplies, 2x Broadcom Gigabit onboard, 2x Intel CPU (many options), 2- 8xPCIe & 1- 4xPCIe Standard (other risers available), SATA HDD ONLY, 2x internal USB - MUST SPECIAL ORDER WITHOUT RAID CONTROLLER. (some issues with floppy netinstall)}
HP Proliant DL380 G5	3.17	Works, but only if installed from CDROM (Netinstall to Windows mounted HDD causes issues)
HP Proliant ML110 G7	5.20	Works, installed from CD-ROM
Asus EEE PC 701	3.x	SFF Laptop, 1x10/100 ethernet (Not detected), Stock Wireless unsupported (AR5007E In Mini-PCIX slot), 630/900Mhz processor, 512MB RAM, 4GB SSD (Not detected), USB2.0 Bootable, SDHC Reader functions as a USB Stick
Dell PowerEdge SC1425	3.x	Rackmount, Intel Xeon 2.8 1MB 800FSB, 1024MB DDR2 PC3200 ECC, 2x Intel 82541GI Gigabit Ethernet, HD150gb SATA, USB works, very stable
Fujitsu Siemens Primergy RX100S5	3.7, 3.22	Can Install from Netinstall with RAID (LSI) Controller enable. Can't install from CD and Netinstall with only SATA or PATA mode. But NOT RUN
Toshiba Magnia SG20	2.9.44	CPU Celeron, VIA chipsets, onboard LAN Realtek and Intel, IDE HDD, PCMCIA tested with Orinoco Silver, miniPCI LT WinModem not work
Advantech FWA-3800	4.11, 4.17, 5.14	CPU Intel Core2 Duo 2,93GHz, 2GB RAM DDR2, 6 x Intel 1Gbps PCIe NIC, 1U size, works good as a BGP router. If you have troubles with MT 5.x on it, try to reset BIOS (by battery remove). Enable ACPI in the BIOS. It is disabled by default in Power Management Setup menu. Without this system does not boot (MT 5.x).
SuperMicro SYS-5015A-EHF-D525	5.18	CPU Intel Atom D525, 2x Intel 82574L 10/100/1000 Ethernet

Embedded Controllers

Model	ROS version	Result
WRAP.1E-2	2.9.51, 3.7	3 Ethernet, 1 miniPCI, 128 MB - Working
WRAP.2E	2.9.51, 3.7, 3.9, 3.10	1 Ethernet, 2 MiniPCI, 128 MB - Work fine
ALIX 2-2	2.9.48	2 Ethernet, 2 miniPCI - Working
Adlink cPCI-6770 Low Power Pentium III	2.9 and 3.0	CompactPCI CPU Module - Working, excellent performance!
Advantech PCA-6751	2.9.49	Working
Soekris 4801-50	2.9.48	3 Ethernet, 128MB, CF 512MB - Working
Soekris 4826-48	3.10	233 Mhz CPU, 128 Mbyte SDRAM, 1 Ethernet, 1 Serial, 256 Mbyte CF Flash, 2 Mini-PCI sockets, PoE. Limited power available/runs only 1 high power card (@26dB) along with another lower power card (@17dB)
Soekris net4801-48/50 + lan1641	3.22	All 7 (3+4) ethernet works, USB works (tested with Huawei 3G modem), extra serial port works. And RouterOS installed on CF card.
ALIX 2C0	2.9,3.0	2 Ethernet, 2 miniPCI ,128Mb 433Mhz Amd Geode- Working Perfect
ALIX 2C1	2.9,3.0	2 Ethernet, 2 miniPCI ,128Mb 433Mhz Amd Geode- Working Perfect
ALIX 2C3	2.9,3.0	2 Ethernet, 2 miniPCI ,256Mb 500Mhz Amd Geode- Working Perfect
ALIX 3C1	2.9,3.0	2 Ethernet, 2 miniPCI ,128Mb 433Mhz Amd Geode- Working Perfect
ALIX 3C2	2.9,3.0	2 Ethernet, 2 miniPCI ,256Mb 500Mhz Amd Geode- Working Perfect
ALIX 2D13	5.2	3 Ethernet, 1 miniPCI ,256Mb 500Mhz Amd Geode- Working Perfect

3G cards and modems

Vendor	Model	Tested RouterOS version	Comments	Format
AirPrime/Sierra	PC 5220!	v3.x and higher		PCMCIA
Alcatel	One Touch X020X USB (aka Longcheer WM66; Nuton NT36HD; MWalker mbd 100hu; Novacom GNS-3.5G White, SU-8200U; MTE MW610?)	v5.10 and higher	Config like Option_Globetrotter_HSDPA_USB_Modem Connected to Internet, Did not test Speed + Reliability (Alcatel OT X020X on x86) (data 0, info channel: 2)	USB
AnyData	ADU-E100A (aka "USB Wireless HSDPA/UMTS 2.1GHz GSM/GPRS/EGPRS 900/17000MHz/CDMA 1x EVDO Rev.A")	v3.x and higher		USB
AnyData	ADU-500A USB (aka "USB Wireless HSDPA/UMTS 2.1GHz GSM/GPRS/EGPRS 900/1800MHz/CDMA 1x EVDO Rev.A")	v3.x and higher		USB
AnyData	ADU-E630WH ( aka "USB Wireless HSDPA/UMTS 2.1GHz GSM/GPRS/EGPRS 900/17000MHz/CDMA 1x EVDO Rev.A")	v6.x and higher		USB
Audiovox	PC5220 CDMA Dual Band 1XEV-DO PC Card	v3.x and higher		PCMCIA
C-motech	CNU-680 CDMA 1x EV-DO 450Mhz USB Modem (used by Triatel) [1]	v3.x and higher		USB
Dell	5520	v3.x and higher		MiniPCI-E
Dell	Wireless 5530 HSPA	v6.1 and higher	Data channel 0, Info channel 0, init: AT+CFUN=1 (needs manualy change profile by command AT*ENAP=1,1)	MiniPCI-E
Ericsson	Ericsson_F3507g_Mobile_Broadband_Module [2]	v3.x and higher	Set init string AT+CFUN=1, data channel and info channel to 3.	MiniPCI-e
Huawei	E226 USB modem,	v3.x and higher		USB
Huawei	E3531 USB modem,	v6.24 and higher		USB
Huawei	E220 USB modem, E200BIS [3]	v3.x and higher		USB
Huawei	E169 USB modem (used by Tele2) [4]	v3.x and higher		USB
Huawei	E180 USB modem	v3.x and higher		USB
Huawei	E1553 USB modem	v3.x and higher		USB
Huawei	E1550 [5]	v3.x and higher		USB
Huawei	E1762 USB Modem	v5.14 and higher	Locks up occasionally on 433UAH. Need to unplug to reset.	USB
Huawei	E372 (USB)	v5.15< and	Videotron Canada: Data channel 0 , Info channel 0, APN ihvm.videotron, Phone = *99# , Dial = ATDT. another operator: After inserting command: AT^SETPORT="A1,A2;1,2,3,7" in huawei terminal, modem starts working with info channel = 1 (when internet connected), Tested in v6.26<	USB
Siemens	M20	v3.x and higher
Huawei	E620;	v3.x and higher		PCMCIA
Kyocera	KPC650	v3.x and higher		PCMCIA
Nokia	CS-17 (USB)	v5.0 and higher	Data channel=2, info channel=4	USB
Nokia	CS-18 (USB) Rogers Canada	5.12 and higher	Data channel=1, Info channel =1, APN= internet.com, Phone = *99# , Dial = ATDT , pap , Tested on rb-751 and rb-493	USB
Novatel	EU740	v3.x and higher		MiniPCI-e
Novatel	EU870 [6]	v3.x and higher		MiniPCI-e
Novatel	MIFI 2372 Bell Canada	v5.12 and higher	Data Channel=0 , Info Channel= 0, APN = pda2.bell.ca , Phone = *99# , Dial = ATDT , pap, Tested on Rb-750UP and RB-493	USB
Novatel	EV620 CDMA/EV-DO	v3.x and higher		MiniPCI-e
Novatel	Merlin ES620 / Merlin ES720 / Ovation U720 [7]	v3.x and higher		USB
Novatel	Merlin ES620	v3.x and higher
Novatel	Merlin S720 (HSDPA) [8]	v3.x and higher		PCMCIA
Novatel	Merlin XU870 HSDPA/3G [9]	v3.x and higher		ExpressCard
Novatel	U720 Wireless CDMA Modem	v4.5 and higher		USB
Novatel	U730 (Wireless HSDPA Modem) [10]	v3.x and higher		PCMCIA
Novatel	Wireless CDMA card	v3.x and higher
Option Fusion	UMTS Quad-GPRS	v3.x and higher		PCMCIA
Option Globetrotter	HSDPA USB aka Teltonika ModemUSB/H7.2 (U3G150) [11]	v3.x and higher		USB
Option Globetrotter	Probably most of the cards needing the HSO driver on Linux, tested: HSDPA USB (Globetrotter iCon 225 [12]	v5.12	Option_Globetrotter_HSDPA_USB_Modem see Workaround for Globetrotter devices offering no modem interface	USB
Option	Qualcomm 3G WCDMA Model M00201-10886 (GTM378) [13]	v3.x and higher		miniPCI-e
Option	Qualcomm 3G CDMA Model M00301 (GTM380) [14]	v3.x and higher	Set data channel and info channel to 3.	miniPCI-e
Option	Qualcomm 3G CDMA Model M00401 (GTM382) [15]	v3.x and higher		miniPCI-e
Ericsson	3G F3607gw miniPCI-e	v3.x and higher	Set data channel and info channel to 2, set init string AT+CFUN=1	miniPCI-e
Sierra Wireless	Aircard 595 [16]	v3.x and higher		PCMCIA
Sierra Wireless	Aircard 595U USB Sprint Card [17]	v3.x and higher		USB
Sierra Wireless	USB 306	v5.9 and higher	Data & Info Channel 2. For Telecom NZ use APN internet.telecom.co.nz and Phone number *99#
Sierra Wireless	USB 308 or AT&T Shockwave [18]	v5.0rc11 and higher	AT Commands are sent through Data Channel 2 or 3.	USB
Sierra Wireless	AirCard 312U [19]	v5.2 and higher		USB
Sierra Wireless	AirCard 580 [20]	v3.x and higher		PCMCIA
Sierra Wireless	AirCard 595 [21]	v3.x and higher		PCMCIA
Sierra Wireless	AirCard 597E [22]	v3.x and higher		ExpressCard
Sierra Wireless	AirCard 875 [23]	v3.x and higher		PCMCIA
Sierra Wireless	AirCard 880 [24]	v3.x and higher		PCMCIA
Sierra Wireless	AirCard 880 E [25]	v3.x and higher		ExpressCard
Sierra Wireless	AirCard 881 [26]	v3.x and higher		PCMCIA
Sierra Wireless	AirCard 881 E [27]	v3.x and higher		ExpressCard
Sierra Wireless	EM5625 [28]	v3.x and higher		MiniPCI-e
Sierra Wireless	MC5720 [29]	v3.x and higher		MiniPCI-e
Sierra Wireless	MC5725 [30]	v3.x and higher		MiniPCI-e
Sierra Wireless	MC8705 [31]	v5.1 and higher		MiniPCI-e
Sierra Wireless	MC8755 [32]	v3.x and higher
Sierra Wireless	MC8755 for Europe [33]	v3.x and higher		MiniPCI-e
Sierra Wireless	MC8765 [34]	v3.x and higher		MiniPCI-e
Sierra Wireless	MC8775 [35]	v3.x and higher		MiniPCI-e
Sierra Wireless	MC8780 [36]	v3.x and higher		MiniPCI-e
Sierra Wireless	MC5725 [37]	v3.x and higher		MiniPCI-e
Sierra Wireless	MC5727 [38]	v3.x and higher		MiniPCI-e
Sierra Wireless	MC8785	v3.x and higher		MiniPCI-e
Sierra Wireless	MC8790 [39]	v3.x and higher	Few models do not send echo for input commands, modem does not work properly.	MiniPCI-e
Sierra Wireless	MC8792 [40]	v5.2 and higher	Info works only in channel 3. Channels 4 and 5 has limited AT set. datachannel=4, infochannel=3	MiniPCI-e
Sierra Wireless	MC8781 [41]	v3.x and higher		MiniPCI-e
Sierra Wireless	598 (Sprint) USB [42]	v3.x and higher		USB
Sierra Wireless	MP3G - EVDO	v3.x and higher
Sierra Wireless	MP3G - UMTS/HSPA	v3.x and higher
Sierra Wireless	Compass 885 (USB) [43]	v3.x and higher		USB
Silicon Labs	MobiData GPRS USB Modem	v3.x and higher		USB
Sprint	U301/301U 4G wireless card [44]	v4.6 and higher	C-MOTECH Co, FW301DOWMX, QUALCOMM Patch 33504--Tested with v4.11 on RB433UAH, Data CH=1 Info CH=3 Phone #777 for Sprint in US	USB
Sprint	U300/300U 4G wireless card [45]	v4.6 and higher	C-MOTECH Co, FW301DOWMX, QUALCOMM Patch 33504	USB
Franklin	M600 3G/4G wireless card [46]	v5.x and higher	only 3G mode	MiniPCI-e
Verizon	Express Network PC5220 (AirPrime 5220)	v3.x and higher
ZTE	AC8700	v3.x and higher
ZTE	MF620 / MF622 [47]	v3.x and higher		USB
ZTE	MF620 / MF622 (3G) [48]	v3.x and higher		USB
ZTE	MF100 [49]	v5.11 and higher	Set info channel = 1, data channel = 2	USB
ZTE	MF110 [50]	v6.28 and higher	Set info channel = 2, data channel = 2, Dial command=ATM1L3DT	USB
ZTE	MF680 [51]	v5.4 and higher	Used by 3 in Sweden. Set data chanel to 1	USB
ZTE	MF668 [52]	v4.5 and higher	for Rogers Wireless (Canada) Set APN: isp.apn and Info & Data Channel to 1	USB
T-Mobile (Germany)	Web´n´Walk Box Micro (Huawei E220) [53]	v3.x and higher		USB
Vodafone (Germany)	Easybox 2 (Huawei E220) [54]	v3.x and higher		USB
	Surfbox Mini (Huawei E220) [55]	v3.x and higher		USB
E-Plus & Base (Germany)	USB Minimodem (Huawei E220) [56]	v3.x and higher		USB
Huawei	E600	v3.x and higher		PCMCIA
Novatel	Merlin V640/XV620 [57]	v3.x and higher		ExpressCard
Novatel	Merlin V620/S620 [58]	v3.x and higher		PCMCIA
Novatel	Merlin EX720/V740/X720 [59]	v3.x and higher		ExpressCard
Novatel	Merlin V720/S720/PC720 [60]	v3.x and higher		PCMCIA
Novatel	Merlin XU870 HSDPA/3G [61]	v3.x and higher		ExpressCard
Novatel	X950D [62]	v3.x and higher		ExpressCard
Novatel	ES620/ES720/U720/USB720	v3.x and higher		USB
Novatel	E725/E726 [63]	v3.x and higher		MiniPCI-e
Vodafone	EU740/Novatel non-Vodafone EU740	v3.x and higher		MiniPCI-e
Vodafone	K3565/Huawei E160 [64]	v3.x and higher		USB
Novatel	EU850D/EU860D/EU870D [65]	v3.x and higher		MiniPCI-e
Novatel	MC930D/MC950D [66]	v3.x and higher		USB
Novatel	MC727/U727 [67]	v3.x and higher		USB
Novatel	Expedite EV620 CDMA/EV-DO	v3.x and higher		MiniPCI-e
Novatel	Expedite EU740 HSDPA/3G, Dell Wireless 5500 Mobile/Dell Wireless 5505 Mobile	v3.x and higher		MiniPCI-e
Novatel	Expedite E720 CDMA/EV-DO	v3.x and higher		MiniPCI-e
Novatel	Expedite ET620 CDMA/EV-DO	v3.x and higher		PCMCIA
Onda	H600/ZTE MF330	v3.x and higher
Onda	MDC525UP		Not supported	USB
Onda	MT833UP (opt. ext. antenna)	v5.6 and higher	Set info channel = 1, data channel = 0	USB
Onda	MT835UP (opt. ext. antenna)	v5.21 and higher	Set info channel = 1, data channel = 0	USB
	BP3-USB & BP3-EXT HSDPA	v3.x and higher		USB
ZTE	MY 39 (MSM 6500 based) [68]	v3.x and higher		PCMCIA
Cricket	A600	v3.x and higherRouterB
Globetrotter	HSDPA Modem Option N.V.	v3.x and higher
Sony Ericsson	MD300	v3.x and higher
ZTE	MF 626 [69]	v3.x and higher		USB
ZTE	MF 627 [70]	v3.x and higher		USB
Pantech / UTStarcom	UM175	v3.x and higher		USB
Novatel	U760 [71]	v3.x and higher		USB
ZTE	K3565-Z [72]	v4.4 and higher	Revision: BD_P673A2V1.0.0B09	USB
Novatel	Expedite EV620	v4.5 and higher		MiniPCI-e
Novatel	MC760 VMU [73]	v4.5 adn higher		USB
Franklin Wireless	FW300DOWMX	v4.5 and higher
Huawei	EC1260	v4.5 and higher		USB
Vodafone	K3520-Z [74]	v4.6 and higher		USB
Vodafone	K3765 [75]	v4.6 and higher		USB
Telstra	3G Elite	v5.x and higher		USB
Vodafone	Huawei K4505	v5.x and higher	Data-channel=0 Info-channel=3	USB
Vertex	VW 110	v5.x and higher
ZTE	MF112 [76]	v5.x and higher	Power issues on mipsbe boards	USB
Huawei	ET127	v5.x and higher		3G
Huawei	EC1261	v5.x and higher		USB
Huawei	E173 [77]	v5.x and higher		USB
ZTE	MF190 [78]	v5.x and higher	Data channel=3 and info Channel=1	USB
ZTE	MF102 [79]	v5.x and higher	Works! Possible that need to change data channel=2 and info channel=2	USB
Option Globetrotter	GT380	v5.x and higher
Simcom	5220	v5.x and higher
Huawei	K3770	v5.x and higher
Novatel	USB551L (Verizon) [80]	v5.9 and higher	Only 3G support (No LTE support)	UB
Novatel Wireless	MIFI4510		Not supported
ZTE	MC2718 [81]	v5.8 and higher	Possible data-channel=0 info-channel=1 GPS(NMEA)=4	MiniPCI-e
LG-VL600 (Verizon)		Not supported
Huawei	EC156 [82]	v5.8 and higher		USB
Vodafone	K3806 [83]	v5.8 and higher		USB
ZTE	MF-210V [84]	v5.9 and higher		MiniPCI-e
Huawei	E398 [85]	v5.9 and higher		USB
Huawei	E367	v5.11 and higher		USB
Huawei	EM770 [86]	v5.11 and higher		MiniPCI-e
Nokia	E52 (Series 60)	v5.12 and higher	Set Usb mode to "PC Suite" in phone menu, Baud rate - 115200, Ports - 0/0, APN - internet, no modem init string, Dial number - *99#	USB
Nokia	E6 (Series 60)	v5.12 and higher	Set Usb mode to "PC Suite" in phone menu, Ports - 0/0, APN - internet, no modem init string, Dial number - *99#, SMS works(ppp connection has to be disabled, on channel 0)	USB
Nokia	6700 Classic (Series 40)	v5.12 and higher	Set Usb mode to "PC Suite" in phone menu Baud rate - 115200 Ports - 0/0 APN - internet Modem init string - ATZ, Dial number - *99# Phone is charged up through the USB port	USB
Alcatel	X220S [87]	v5.13 and higher		USB
	MO835UP	v5.14 and higher		USB
Nokia	Datacard CS-11 & CS-15	v5.14 and higher		USB
ZTE	MF821	v5.15 and higher		USB
Huawei	K4510 [88]	v5.15 and higher		USB
Huawei	E173s	v5.15 and higher		USB
Huawei	E352		Supported, if you remove the PIN and change the Data-channel to '2'. Info-channel is '0'.	USB
Option3G	Mini-PCI model GTM661W		Not supported	USB
Option	225	v5.15 and higher		USB
ZTE	AC682		might not work	USB
ZTE	AX320	v5.15 and higher		USB
ZTE	AC5730	v6.x		USB
ZTE	MF 652	v5.15 and higher		USB
Vodafone Huawei	K-4605	v5.15 and higher		USB
Huawei	E353	v5.15 and higher	Some revisions might not work.	USB
CELOT	CT-680	v5.16 and higher		USB
Huawei / ZTE	669T [89]	v5.8 and higher	Info/data =1 and 2 worked	USB
Huawei / ZTE	MF195 [90]	v5.18 (maybe 5.17, but 5.16 not worked)	Info/data =1 worked	USB
Haier	CE81B	v5.21		USB
Huawei	E1731	v5.21 and higher		USB
Huawei	EM820W [91]	v5.11 and higher	Data channel=0, Info channel=2, Keep info channel open	MiniPCI-e
Alcatel	X221L [92]	v5.20 and higher		USB
Telecom	NZ T-Stick ZTE MF-181	v6.0rc13	Data Channel=2, Info Channel=2, APN internet.telecom.co.nz, PHONE=*99#. Tested ok for both data and SMS on CCR1016-12G	USB
Huawei	MU609 mPCIe [93]	v6.0	Data channel=4, Info channel=2, Keep info channel open	MiniPCI-e
Huawei	ME909u-521 [94]	v6.0	Data channel=4, Info channel=2, Keep info channel open	MiniPCI-e
Quectel	UC15	v6.xx	Works	MiniPCI-e
Quectel	UC20	v6.xx	Works (Data channel=3, Info channel=2)	MiniPCI-e
ZTE	MF193		Not supported! vendor-id="0x19d2" device-id="0x2000"	USB
D-Link	DWM-221 (A1)		Not supported! This revision uses unsupported QMI interface. vendor-id="0x12d1" device-id="0x1573"	USB
SIMcom	SIM5360 [[95]]	v6.xx	Works! Using PPP interface (data-channel-2,info-channel-3), vendor-id="0x05c6" device-id="0x9000"	MiniPCI-e / USB w/ converter

* - Currently MikroTik RouterOS works with PPP 3G modems over serial interfaces, 4G modems with IP drivers are not supported.

4G LTE cards

LTE should be configured under the new "/interface lte" menu

Model	Tested RouterOS version	Comments	Format
BandRich C501 [96]	v5.25 and v6.0		USB
Sierra Wireless MC7710/MC7700 [97]	v5.25 and v6.0	If modem uses firmware 3.5 it should be upgraded to 3.5.23.2 firmware release in order to work in RouterOS correctly again.	MiniPCI-e
Yota LU150 [98]	v5.22 and v6.4	Some settings are ignored. Works in Russian markets.	USB
Yota WLTUBA-107 [99]	v6.0	Some settings are ignored. Works in Russian markets.	USB
Yota wifi modem [100]	v6.7	Some settings are ignored. Works in Russian markets.	USB
Vodafone K4305 [101]	v6.7	Some settings are ignored.	USB
Android usb tethering interface	v6.7	Some settings are ignored.	USB
ZTE MF823 [102]	v6.8	Some settings are ignored.	USB
Vodafone K4201-Z [103]	v6.8	Some settings are ignored.	USB
ZTE MF827 [104]	v6.8	Some settings are ignored.	USB
Huawei E3272 [105]	v6.8	Some settings are ignored. There are multiple versions of this modem. Looks like only modem with device-id="0x14db" works as LTE interface.	USB
Huawei MU609 [106]	v6.11		MiniPCI-e
Huawei MU709s-2 [107]	v6.28		MiniPCI-e
Huawei ME909u-521 [108]	v6.11		MiniPCI-e
SIMcom SIM7100	v6.xx(ppp) v7.xx (LTE)	Works! PPP interface (data-channel-2,info-channel-3). And starting with v7.xx it will support LTE interface. vendor-id="0x1e0e" device-id="0x9001"	MiniPCI-e / USB w/ converter
Sierra wireless MC7354	v7.xx	Works! LTE interface and PPP interface	MiniPCI-e

Memory cards

NB! New flash cards need always formatting!

Legend:

• V - works
• X - doesn't work
• ? - not tested
• NA - not available for this RB

Model	Type	RB600	RB1000	RB433AH	RB450G	R493G
PQI 4GB 120x HiSpeed	CF	X	?	NA	?	?
2GB Transcend 133x	CF	X	?	NA	?	?
2GB Kingston 133x (Elite Pro, code CF/2GB-S2)	CF	V	?	NA	?	?
4GB Kingston 133x (Elite Pro)	CF	?	V	NA	?	?
4GB Kingston CF/4GBIN	CF	X	?	NA	?	?
8GB A-Data Speedy G08GNMC7B0095	CF	V	V	NA	?	?
16GB A-Data Speedy	CF	V	V	NA	?	?
4GB Apacer Photo Steno IV 300X	CF	X	X	NA	?	?
1GB Sandisk Ultra II BB05024GA	CF	V	V	NA	?	?
2GB Sandisk Ultra II	CF	?	V	NA	?	?
8GB Sandisk Ultra II	CF	?	V	NA	?	?
8GB SanDisk Extreme III (200X,30MB/s)	CF	?	V	NA	?	?
2.5GB Seagate ST1 (ST625211CF)	CF microdrive	V	V	NA	?	?
8GB Seagate ST1	CF microdrive	V	V	NA	?	?
64MB Nokia	microSD	NA	NA	?	V	?
512MB Kingston	microSD	NA	NA	V	?	?
1GB Apacer	microSD	NA	NA	V	?	?
1GB Kingston (SDC/1GB)	microSD	NA	NA	?	X	?
2GB Kingston	microSD	NA	NA	X	X	?
2GB Traxdata	microSD	NA	NA	?	V	?
4GB Apacer SDHC (class 6)	microSD	NA	NA	V	X	?
4GB Axiz	microSD	NA	NA	V	?	?
4GB Kingston	microSD	NA	NA	V	?	?
4GB Kingston SDHC (C04G JAPAN class 4)	microSD	NA	NA	V	?	?
4GB Maxell SDHC (class 2) P-series	microSD	NA	NA	?	?	V
4GB Transcend SDHC	microSD	NA	NA	V	?	?
4GB Sandisk Mobile Ultra Micro SDHC (with card reader)	microSD	NA	NA	?	V	?
8GB Sandisk SDHC (0733702482DLE)	microSD	NA	NA	V	V	?
8GB Sandisk Mobile microSDHC (SDSDQ-8192-A11M)	microSD	NA	NA	?	V	?
8GB Sandisk Mobile Ultra SDHC (Class 6)	microSD	NA	NA	?	V	?
8GB Kingston SDHC (Class 4)	microSD	NA	NA	V	X	?
8GB ADATA micro SDHC (AUSDH8GCL6) (Class 6)	microSD	NA	NA	?	V	?
16GB Sandisk micro SDHC (SDSDQ-16384-P36M) class 2	microSD	NA	NA	NA	X	?
16GB Sandisk micro SDHC (0835B03279DQ) class 2	microSD	NA	NA	V	V	?
2GB Sandisk micro SDHC class 2	microSD	NA	NA	NA	X	V
4GB Sandisk Mobile microSDHC (SDSDQM-004G-B35S) class 4	microSD	NA	NA	?	X	X
2GB Transcend microSD (TS2GUSD) class not stated	microSD	NA	NA	?	X	?

Note: Pushing the "Kingston SDHC 8GB card" all the way into the socket caused the card not to work properly! It had to be pulled out ~1mm for it to work!

802.11a/b/g wireless cards

Model	Form factor	Platform	ROS	Result
RouterBOARD R52 [109]	miniPCI	ALL	ALL	Natively supported!
RouterBOARD R52H [110]	miniPCI	ALL	ALL	Natively supported!
TechnicLan TMP-5414A	miniPCI	All RouterBOARDs	2.9 / 3.x / 4.x	Perfect, Stable
Compex WLM54AG-20	miniPCI	RB1xx / RB3xx / RB4xx / RB5xx / RB6xx / x86	2.9 / 3.x / 4.x	Perfect, Stable
Compex WLM54A-26	miniPCI	RB1xx / RB3xx / RB4xx / RB5xx / RB6xx / x86	2.9 / 3.x / 4.x	Perfect, Stable
SparkLAN WMIA-165G	miniPCI	RB1xx / RB3xx / RB4xx / RB5xx / RB6xx / x86	2.9 / 3.x / 4.x	Perfect, Stable
SparkLAN WMIA-166AG	miniPCI	RB1xx / RB3xx / RB4xx / RB5xx / RB6xx / x86	2.9 / 3.x / 4.x	Perfect, Stable
SparkLAN WMIA-166AGH	miniPCI	RB1xx / RB3xx / RB4xx / RB5xx / RB6xx / x86	2.9 / 3.x / 4.x	Perfect, Stable
Alfa AWPCI 085 H	miniPCI	RB1xx/RB333/RB4xx/x86	2.9&3.x	All just perfect
TP-Link TL-WN550/551	PCI	x86	2.9&3.x	Perfect 19dB rated, stable at 21
TP-Link TL-WN650/651	PCI	x86	2.9&3.x	Perfect 19dB rated, stable at 21. Unstable with compression activated
D-Link AG530 a/b/g (both rev.A1 and A2)	PCI	x86	2.9&3.x	Perfect. Works perfect, in both 2.4 and 5.x GHz
D-Link DWL-G510	PCI	x86	only 2.9.x tested	Perfect. Tested Rev A1
D-Link DWL-G520	PCI	x86	2.9.x & 3.x	Works well.
D-Link DWL-G520+A/RaLink 2591 Chipset	PCI	x86	4.9	NOT Work!
Gigabyte b/g GN-WI01GT	miniPCI-e	x86	3.x	Works also in RouterBOARDs with miniPCI-e slot
Senao NL-2511CD EXT2	PCMCIA	x86&rb230	only 2.9x tested	Perfect. Just about the most sensitive card i used, in the good sense. Only 11b.
Planet WL-8310	PCI	x86	only 2.9.x tested	Perfect. Stability.
Netgear WG311T 108	PCI	x86	only 2.9x tested	Perfect. stability
SMC SMCWPCIT-G	PCI	x86	3.x tested	Perfect on A/B/G.
Wistron DCMA-81	miniPCI	x86,rb	2.9.xx, 3.xx	Perfect on A/B/G with or without compression.
Wistron DCMA-82	miniPCI	rb	3.xx	Works on some RB, but on 2/3 of my RB433 it causes the board to reboot when enabled. Many other people have had similar experiences. Not recommended. Maybe OK on 133
Senao NMP-8602	miniPCI	x86&rb411	2.9x,3.x tested	Perfect on a/b/g
Dbii F20	miniPCI	RB411 & RB433	3.x tested	Perfect on B/G, too thick for 3 in rb433
Dbii F50	miniPCI	RB411 & RB433	3.x tested	Perfect on A, too thick for 3 in rb433
Dbii F20-PRO	miniPCI	RB411 & RB433	3.x tested	Perfect on B/G, too thick for 3 in rb433
Dbii F50-PRO	miniPCI	RB411 & RB433	3.x tested	Perfect on A, too thick for 3 in rb433
TP-Link TL-WN751ND]	PCI	x86	v5.xx, v6.xx	Not Working!
TP-Link TL-WN851ND]	PCI	x86	v5.xx, v6.xx	Working
TP-Link TL-WN881ND]	PCI-e	x86	v5.xx, v6.xx	v5.xx NOT working not appear in interfaces, v6.x working (6.1 unstable after scan stop working in client or manual scan, set to AP-bridge mode working ok)
XR2	miniPCI	RB433	3.x	works
XR5	miniPCI	RB433, x86	3.x	works
SR9	miniPCI	RB433	3.x	works
SR9	miniPCI	RB411 & RB433	3.x	works
Valemount KXS30SG	miniPCI	RB433	3.2 & 4.2 tested	B/G only, no A. Big heat sink means card should be installed on highest mount when other cards being used. High power consumption can cause power problems, otherwise works perfectly.
Zcomax XG-650	miniPCI	RB112 & RB433	4.2 & 4.6	Not working (driver doesnt work / exist). It has a TI TNETW1130GVF chipset.
AR5BMB5	miniPCI	RB411,x86	3.xx, 4.3	Not working. Atheros chipset.

802.11n wireless cards

Model	Form factor	ROS	Result
RouterBOARD R2N	miniPCI	4.0b3	works
RouterBOARD R52N	miniPCI	4.0b3	works
RouterBOARD R5H	miniPCI	v4	works
SparkLAN WMIA-198N	miniPCI	4x, 5x	Works
Compex WLM200N5-23	miniPCI	4.0b3	Works
Compex WLM200NX	miniPCI	4.0b3	Works
Dbii F52N-PRO	miniPCI	5.1	Works
TP-Link Wireless N (2T2R)	miniPCI	4.0b3	Works
Ubiquiti	miniPCI	4.0b3	Works
Ubiquiti	miniPCI	4.0b3	Works

USB wireless cards

Model	Form factor	ROS	Result
802 b/g/n AR9271	USB	5.0rc4	works
802 b/g/n AR9271 Ubiquiti WiFiStation	USB	5.8 x86	works on N but causes reboot on G
802 b/g/n AR9271 ALFA AWUS036NHA	USB	5.14 x86	works
802 b/g/n AR9170 NETGEAR WN111v2	USB	5.16 x86	Don't recognize

T1/E1

Model	Form factor	Platform	ROS	Result
Farsite FarSync TE1	PCI	x86	3.15	supported

Note: Since v3.15 RouterOS doesn't support any Sync/T1/E1 cards except select Farsite models

GPS

Model	Connection	Platform	ROS	Result
EXAMPLE	USB	x86	3.30	supported

Storage controllers (SAS/SCSI)

Basic RAID support added in RouterOS v5

Brand	Model	Motherboard	RouterOS	Works	Type
HP	Smart Array E200i	x86	v5rc1	No	SCSI
3ware	3w-9xxx	x86	v5rc8	Yes	SCSI
Areca	arcmsr	x86	v5rc8	Yes	SCSI
Megaraid	Megaraid (some Dell servers)	x86	v5rc8	Yes	SCSI

LCD panels

Brand	Model	Motherboard	RouterOS	Works / Doesn't
Crystalfontz	CFA-633v1.5	x86	v5RC10	Works
Crystalfontz	CFA-633v1.3	x86	v5RC7-RC10	Didn't work

USB storage

Note: USB storage device that does not require special drivers or is compatible to work with generic USB storage drivers will work. Devices include external hard drives, USB flash drives

Brand	Model	Works / Doesn't
generic	USB flash drive	Works
Kingston	DataTraveler 2GB	Works

SFP modules

Brand	Model	Rate	Connector/Cable type	Wavelength	Tested with	Works / Doesn't
MikroTik	S-85DLC05D	1,25G	Dual LC, MM	850	CCR/RB2011	Natively supported
MikroTik	S-31DLC20D	1,25G	Dual LC, SM	1310	CCR/RB2011	Natively supported
MikroTik	S-35LC20D	1,25G	LC, SM	T1310nm/R1550nm	CCR/RB2011	Natively supported
MikroTik	S-53LC20D	1,25G	LC, SM	T1550nm/R1310nm	CCR/RB2011	Natively supported
Finisar	FCLF-8521-3	10/100/1000	RJ45, Cat6	-	RB2011LS-IN	Works!
Finisar	FCLF-8521-3-MD	10/100/1000	RJ45, Cat6	-	RB2011LS-IN	Works!
Finisar	FTRJ8519P1BNL-B1	10/100/1000 1.25 Gb/s 1000Base-SX Ethernet & Dual Rate 1.063/2.125 Gb/s Fibre Channel	LC, MM	850	RB2011LS-IN	Works!
Finisar	FTLF8519P2BNL	10/100/1000 1.25 Gb/s 1000Base-SX Ethernet & Dual Rate 1.063/2.125 Gb/s Fibre Channel	LC, MM	850	RB2011LS-IN	Works!
Unica	SFP-1.25G-T	1000M	RJ45, Cat6	-	RB2011LS-IN	Works!
Dell	FTLX8571D3BCL	1,25G	LC, MM	850	RB2011LS-IN	Works!
Unica	GP-3124-L2CD-C	1,25G	LC, MM	1310	RB2011LS-IN	Works!
Cisco	SFP-10G-LR	10G	LC/PC, SM	1310	RB2011LS-IN	Works!
Cisco	GLC-T	1.25G	RJ45, Cat6	-	RB2011LS-IN	Works!
Cisco	GLC-SX-MM	1000BASE-SX SFP transceiver module for MMF, 1.25G	LC/PC, MM	850	RB2011LS-IN	Works!
6COM	6C-SFP-T	10/100/1000	RJ45, Cat6	-	RB2011LS-IN	Works!
6COM	6C-WDM-0210BSD	1,25G	Bi-Di SC, SM	1550/1310	RB2011LS-IN	Works!
6COM	6C-WDM-0210ASD	1,25G	Bi-Di SC, SM	1310/1550	RB2011LS-IN	Works!
6COM	6C-SFP-0310D	1,25G	LC, MM	1310	RB2011LS-IN	Works!
6COM	6C-SFP-0301D	1,25G	LC, MM	850	RB2011LS-IN	Works!
Ingellen	INSP-T(10/100/1000)	10/100/1000	RJ45, Cat6	-	RB2011LS-IN	Works!
Ingellen	INSPL-53-BX	1,25G	Bi-Di LC, MM	1550/1310	RB2011LS-IN	Works!
Ingellen	INSPL-35-BX	1,25G	Bi-Di LC, MM	1310/1550	RB2011LS-IN	Works!
Ingellen	INSP -LX-SM	1,25G	LC, MM/SM	1310	RB2011LS-IN	Works!
Ingellen	INSP-SX-MM	1,25G	LC, MM	850	RB2011LS-IN	Works!
AXCEN	AXGT-R1T4-05I1	10/100/1000	RJ45, Cat6	-	RB2011LS-IN	Works!
AXCEN	AXGD-37А4-0531	1,25G	Bi-Di LC, MM	1550/1310	RB2011LS-IN	Works!
AXCEN	AXGD-16А4-0531	1,25G	Bi-Di LC, MM	1310/1550	RB2011LS-IN	Works!
AXCEN	AXGD-1354-0531	1,25G	LC, MM	1310	RB2011LS-IN	Works!
AXCEN	AXGD-5854-0511	1,25G	LC, MM	850	RB2011LS-IN	Works!
TP-Link	TL-SM311LS	1,25G	LC, SM	1310	RB2011LS-IN	Works!
TP-Link	TL-SM311LM	1,25G	LC, MM	850	CCR1036 12G-4S	Works!
OPTIC	OPTIC-SFP-3524S-02-SC	1,25G	BiDi SC, SM	TX1310/RX1550	RB2011UAS-RM, RB260GS	Works!
OPTIC	OPTIC-SFP-5324S-02-SC	1,25G	BiDi SC, SM	TX1550/RX1310	RB2011UAS-RM, RB260GS	Works!
OPTIC	OPTIC-SFP-S1203-L3302-LC	1,25G	BiDi LC, SM	TX1310/RX1550	RB2011UAS-RM, RB260GS	Works!
OPTIC	OPTIC-SFP-S1205-L3302-LC	1,25G	BiDi LC, SM	TX1550/RX1310	RB2011UAS-RM, RB260GS	Works!
ROBOFiber	SFP-7120-55	1,25G	LC, SM	1550nm	CCR1036-12G-4S, RB2011	Works!
ROBOFiber	SFP-7120-WA - SFP-7120-WB	1,25G	LC, MM	Tx:1490/Rx:1550nm - Tx:1550nm/Rx:1490nm	CCR, RB2011	Works!

USB serial adapters

Note: when USB serial port is connected RouterOS might attach serial console on the port. Before using it for something else, disable the console on the interface

Brand	Model	Works / Doesn't
	USB U209-000-R Serial-Port	Works
	FT232RL chipset	Works
Gembird	Prolific Technology Inc. (USB-Serial Controller)	Works

USB Ethernet

Note: see if device works with one of these linux kernel modules. If yes, it will be possible to use it on RouterOS

RouterOS on x86 have these modules enabled

• USB_PEGASUS
• USB_RTL8150
• USB_USBNET
• USB_NET_AX8817X
• USB_NET_CDCETHER
• USB_HSO

RouterOS on mips have these modules enabled:

• USB_NET_MCS7830
• USB_NET_AX8817X
• USB_NET_CDCETHER
• USB_HSO
• USB_USBNET

AX88178 (USB2.0 Gigabit Ethernet) recognized but not working.