Manual:LCD TouchScreen

From MikroTik Wiki
Jump to navigation Jump to search

Applies to RouterOS: v5.19+


RouterBOARD 2011U and CCR series devices are equipped with a resistive touchscreen, for quick access to device stats and simple configuration options. Touchscreen requires pressure against the surface to register a touch, therefore light swipes and quick/short taps might not get registered (as opposed to a capacitive touchscreen commonly found on phones). If you find trouble operating the screen with your finger, you can also try a stylus, or opposite end of a pen.

General Configuration

Sub-menu: /lcd

LCD Touch screen is configurable from the /lcd console menu.

Property Description
enabled (yes | no; Default: yes) Turns LCD touchscreen backlight on or off
backlight-timeout (time interval: 5m..2h | never; Default: 30m) Time after which LCD touchscreen is turned off
read-only-mode (yes | no; Default: yes) Enables or disables Read-Only mode
current-interface (string; Default: ) Physical interface which is displayed first in Stats screen
time-interval (min | hour | daily | weekly; Default: min) Time interval of current-interface statistics in Stats screen
all-interface-mode (rx | tx; Default: tx) Displayed statistics of interfaces in All Interface Stats screen

Available functions:

  • recalibrate - Starts LCD touchscreen calibration process;
  • take-screenshot - Takes BMP image of currently displayed LCD screen.

LCD Touchscreen Calibration

Before the LCD touchscreen can be used, it needs to be calibrated at least once. After the first successful calibration, data is stored on the router. If no calibration values are present, calibration process will start automatically.

During the calibration/recalibration you must touch 4 points drawn on the screen. Three of the points are used to calculate calibration variables and the 4th point is used to test whether the calibration was successful. If calibration is unsuccessful, calibration variables are not saved. At the end (after touching 4th point) a message is displayed with the calibration result.

LCD screens/modes

Graph Screen

Graph screen shows single interface graphs for RX and TX. Values are updated from right to left (newest to oldest). Info that is shown: RX/TX rate, packets, drops, errors.

Interface name is shown at the bottom right, it is trimmed if it's too long (last characters are cut off). The top right corner shows the time interval for the values. Following time values are available:

  • Min (Minute) - shows values for the last minute. Unit = second. Vertical line separates first 30 seconds. Total values: 30 + 24;
  • Hour - shows values for the last hours. Unit = 5 minutes. Vertical lines separate 1 hour. Total values: 12 + 12 + 3;
  • Daily - shows values for the last days. Unit = hour. Vertical lines separate 1 day. Total values: 12 + 12 + 3;
  • Weekly - shows values for the last weeks. Unit = day. Vertical lines separate 1 week. Total values: 7 + 7 + 4;


  • Tap - tapping the finger against the touch screen without moving it too much.
    • If a tap lands into the top right corner of the screen (square box 1/4 of the screen height), info time interval is changed: Min -> Hour -> Daily -> Weekly -> Min...
    • Otherwise a tap cycles through graph info: rate -> packets -> drops -> errors -> rate...
  • Swipe/Drag - while holding the finger down, move in any direction. The changes should be highlighted during the drag.
    • Down - Select All Interface graph screen
      • Left - Next interface
      • Right - Previous interface

All interface graph screen

All interface graph screen shows single info (RX or TX Rate, packets, errors, drops) for all interfaces. Values are updated every second. The goal of this screen is to see how values are related to each other for a single interface.


  • Tap on the top left corner changes TX/RX.
  • Swipe/drag changes are highlighted.
    • Up - Back (to Graph screen).
    • Left/Right - select info type: Rate, Packets, Errors, Drops.


Allows setting a PIN code number, to protect sensitive menus on the LCD screen. The PIN number will be asked if you add an IP address, or Reset the router. Default PIN is 1234

Available properties:

  • pin-number - the PIN protection code (default is 1234)
  • hide-pin-number - whether to show the typed numbers on the screen, or hide them with asterisks

See Also

[ Top | Back to Content ]